StarTech.com ADJ-TABLET-STAND-W User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support
Manual Revision: June 20, 2022 4:53 PM
Product Diagram (ADJ-TABLET-STAND-W)
Front View
Component Function
1Clamp
• For up to 12.9 in Tablets. Holders on either side
support the Tablet in place
• Width range from 5 to 8 in (12.8 to 22.4 cm)
• Maximum thickness 0.4 in (1.1 cm)
• Allow to rotate 360°, up and down, and side to side
2Rotation Adjustment
Knob
• Varies the Rotation resistance of the Clamp or xes it
on a specic position
3Clamp Tilt
Adjustment Screw • Adjust the Resistance of the Tilt Angle of the Clamp
4Support Arm Tilt
Adjustment Screws
• Adjust the Resistance of the Tilt Angle of the Upper
and Lower sections of the Support Arm
5Support Arm • Supports the weight of the Tablet and provides
Height and Tilt Adjustment
6Mounting Holes • Allow to x the Tablet Stand on a permanent location
7Base • Supports the Assembly in place. Foam Pads at the
bottom protect the desk or table surface
Universal Tablet Desk Stand - White
Package Contents
• Tablet Stand x 1
• 4.2x19 mm Wood Screws x 4
• 3 mm Hex Key x 1
• 5 mm Hex Key x 1
• Quick-Start Guide x 1
Requirements
For the latest manuals, product information, technical specications, and declarations of
conformance, please visit: www.startech.com/ADJ-TABLET-STAND-W
• Phillips head screwdriver
Operation
WARNINGS!
Do not exceed the weight capacity of this product. Overloading this product might
result in injury or property damage. This product can support the following weight: up
to 2.2 lb (1 kg).
When adjusting the tilt or height of this product, ensure that the mounted equipment
is properly secured and the weight is fully supported. Failure to follow these guidelines
may result in property damage and/or personal injury.
When not xed to a surface, always use two hands to ensure a controlled movement
when adjusting the height or tilt angle of this product to prevent tipping it over.
Is recommended to remove any protective case from the Tablet to t properly on the
Holders.
1. Slide the Holders outwards to make enough room to mount the Tablet Vertically
on the Clamp. If the Tablet is Small enough, it can be mounted Horizontally too.
Figure 1
7
6
1
5
2
4
4
3
*Product may vary from image

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or
symbols of third-party companies not related in any way to StarTech.com. Where they occur these references
are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
com, or an endorsement of the product(s) to which this manual applies by the third-party company in question.
StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other
protected names and/or symbols contained in this manual and related documents are the property of their
respective holders.
Warranty Information
This product is backed by a 5-year warranty. For further information on product warranty terms and conditions,
please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors,
employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential,
or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the
product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this
statement may not apply to you.
Safety Measures
• Read the entire manual and ensure the instructions are fully understood before assembling and/or using
this product.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
Mesures de sécurité
• Lisez tout le manuel et assurez-vous que vous comprenez les instructions avant de commencer à assembler et utiliser ce
produit.
安全対策
• 最初に取扱説明書を最後まで読み、本製品の組み立て方をすべて理解してから組み立て作業を始めて下さい。
Misure di sicurezza
• Leggere l’intero manuale e assicurarsi di aver compreso tutte le istruzioni prima di iniziare ad assemblare e a utilizzare
questo prodotto.
Säkerhetsåtgärder
• Läs hela manualen och se till att du förstår instruktionerna innan du börjar montera och använda produkten.
2. Insert one side of the Tablet on one of the Holders. Keep Supporting the weight
of the Tablet .
3. Slide Inwards the remaining Holder to secure the Table in place. Figure 1.
Adjust the Rotation Resistance of the Clamp
1. Rotate Clockwise to Tighten the Resistance Knob at the back of the Clamp. The
right resistance allows the Clamp to rotate 360°, up and down, and side to side
while keeping its position when the Tablet is in use.
Adjust the Tension of the Clamp Tilt
1. Use the 5 mm Hex Key and rotate Clockwise to Increase the Resistance. The
right Resistance allows the Clamp to rotate up and down while keeping its
position when the Tablet is in use.
Adjust the Tension of the Support Arm Tilt
1. Use the 5 mm Hex Key to tune one or two of the Support Arm Tilt Adjustment
Screws. Rotate Clockwise to Increase the Resistance.
Attach the Tablet Stand to a Desk
May need pilot holes before mounting the Tablet Stand.
The supplied Wood Screws may not be suitable if they are longer than the thickness
of the mounting surface.
1. Insert the 4.2x19 mm Wood Screws (x 4) onto the Mounting Holes (x 4) on the
Base.
2. Use a Phillips Head Screwdriver to fasten the 4.2x19 mm Wood Screws to the
Desk or Table.
(Optional) Secure the Support Arm onto the Base
1. If the Screws at the bottom of the Base come loose, use the 3 mm Hex Key to
Tighten them. Rotate Clockwise to Tighten.