StarVedia IC722z User manual

Download the mCamView Z+ user manual here
http://www.starvedia.com/download.html
STEP 1
mCamView Z+
Download the mCamView Z+ APP
Scan the QR code to download the software “mCamView Z+”
from App Store for iPhone/iPad
or from Android Market for Android devices.
Setup the camera from a Smartphone/Tablet
Requires iOS 6.0 or later
iOS iPhone、iPad
Requires Android 4.0 or Later
Android Smart phone、Tablet
Full HD Z-WAVE Smart Home Kit Quick Installation Guide
STEP 3
Log into the Z-WAVE CAMERA
STEP 4
Add a Z-Wave Device
STEP 5
Add a new room
After a room is added, click the room icon to add Z-Wave
devices into the room. If there are temperature sensor and
humidity sensor in the room, the temperature and humidity
value will be displayed on the room icon.
If there is a camera installed in a room, add that camera
into the room, then the camera video will be displayed for
the room when this room is clicked in the live video display.
a Tap the "ROOM” icon.
b Tap ” ”.
c Tap ”+” to add a new room.
d Name the room.
a
bd
STEP 2
Setup the camera
Please click the “ ” icon on the App and follow the instructions
to setup the camera.
a
b
Tap the camera icon to log into the camera.
Key in the administration account to log in.
The default administration account is “admin”,
the default administration password is empty (leave blank).
After logged in, tap the camera icon to play the live video.
Notice : there are two passwords for the Z-Wave camera,
one is the admonistration password, the other one is the
video play password.
To include(pair) a Z-wave device into the camera :
1.Set the camera into inclusion mode
a.Tap the “DEVICE” icon on the App
b.Tap “ ” and “OK”
c.A “beep” sound is generated by the camera to start the
inclusion mode
2.Set the Z-wave device into inclusion mode
(Please check the user manual of the Z-Wave device to set
the inclusion mode)
3.When the camera recognize the Z-Wave device, a “doo”
and then a success sound will be generated by the camera
Notice : If the device failed to be added to the camera, please check
(1).If the Z-Wave frequency of the device is the same as the camera.
(2).May need to exclude the device first,please tap “-“ under “DEVICE”
to do the exclusion procedure.
c

Default admin user name: admin
Default admin password: (leave blank)
STEP 6
Add a new scene
Each home can create up to 20 scenes, and each scene
consists of IF/THEN/WHEN elements.
“IF” is the conditions that will trigger this scene, up to 6
conditions are allowed in each scene, these conditions
could be “and/or” operated. The “IF” conditions could be
set according to the status of the Z-Wave devices, room
conditions or Z-Wave camera status.
“THEN” is the actions of this scene, up to 6 actions are
allowed in each scene. The “THEN” actions could be the
actions of the Z-Wave devices, room actions or Z-Wave
camera actions.
“WHEN” allows this scene conditions to be checked
always, every day, every week or during some time period.
Quick Installation Guide
What should I do if I have forgotten the password or the ID/Password
card is missing?
Please press the Reset button for five seconds. The camera will reset to the
factory default settings. The default video-play password is ipcam(lowercase).
What should I do if I cannot see the video remotely?
The red LED of the camera should be remain on when the camera is connected to the
Internet. If the red LED is blinking, please double check the network
connection and settings again.
I can see the video in a remote place, but the video quality is not good and
sometimes the video would disconnect and then reconnect again by itself.
It's probably because the internet bandwidth (internet speed) is not big enough.
Please try to apply for a better internet connection from your Internet Service
Provider or decrease the bandwidth setting of the camera.
What is the default admin user name/password?
Q1
Q2
Q3
Q4
Q5
Q3
Where to download the latest mCamView Z+ App?
Please scan the QRCode.
SD Card Recording
* Note: Class 10 micro SD is prerequisite
a Insert the SD card into the camera, the yellow LED on the
camera will be blinking.
b The SD card will start to do the recording once the alarm
notification is triggered. The camera will do 5 second
pre-recording to prevent the loss of the important starting
moment.
c To enable the continuous SD card recording, please enable
it inside the camera settings.
d To playback the recorded video, tap the on the upper
right corner of the App and choose the “SD Card”. Choose
from the camera list and date/time to do the playback.
Ans
Ans
Ans
Ans
Ans
Full HD Z-WAVE Smart Home Kit
Package Contents
FAQs
More FAQs, please visit www.starvedia.com/download.html#faq
aTap "+" to add a scene.
bName the scene.
cDo the scene settings.
For more details, please see the
mCamView Z+ user manual.
STEP 7
Scene Interface
The App will get alarm notification when one of the following events happened.
All the trigger events could be set and be enabled or disabled.
Please refer to the user manual for detailed settings.
[ FRONT ] [ BACK ]
[ TOP ] [ BOTTOM ]
Power Plug 4 in 1 Sensor
a Back to previous page
b Add a scene
c Remove scenes
d Tap to program the scene
e Enable/Disable this scene
f Do the scene actions
g Rename a scene or change its ICON
h Enable/Disable alarm (push) notifications
while this scene is triggered
b c
de
f
g
h
a
Product View
a When the Z-Wave device changed status.
b When the scene is triggered.
c When the camera event is triggered, like the sound or motion detection.
Alarm Notification
ID/Password Card
Power Adapter + Power Extension Cable Power Adapter
or
Ethernet Cable
Anchors
and Screws
QIGCamera