Stealth BBEUZ460 User manual

4
User Manual BBEUZ4 Series
High Power Building Amplifier
Mobile
Signal Amplifier
RX/TX
MULTI BAND 60-70dB
60-70dB 4 Band
GSM,HSPA,CDMA,LTE, LTE A
2G, 3G, 3G+, 4G, 4G+
4 Band
Stealth Z4 4G LTE
60 -70dB
High Power Building Amplifiers
Z460 Z465 Z472
MULTI BAND
stealth
tech
®
model shown: BBEUZ460
Smoothtalker.com
Building
[e-mail]
In 2001 SmoothTalker produced the rst digital mobile Mobile signal Amplier
in North America with FCC and ICAN approval. We continue to lead with the
most powerful and intelligent Ampliers in the world.
Our dynamic adaptive proprietary algorithms make them very network friendly.
We call it STEALTH TECH technology.
Band 1
Band 3
Band 8
Band 20
1800MHz
900MHz
800MHz
2100MHz
Smoothtalker.com
stealth
tech
®
Automatic power
control protects the
Mobile Network
RE Directive 2014/53/EU
Certified Compliant
For Inquires please contact Us
[e-mail]
Contact information for Amplier registration:
Some providers have set up web-sites for Amplier registration. If you don’t see
your provider on this list, please contact your provider for information on how
to register your Amplier.
AT&T: https://securec45.securewebsession.com/attsignalAmplier.com/
Verizon: http://www.verizonwireless.com/solutions-and-services/accessories/
register-signal-Amplier/
T-mobile: https://www.signalAmplierregistration.com/
Sprint: https://www.sprint.com/legal/fcc_Ampliers.html
Us Mobile: http://www.usMobile.com/usMobile/support/fcc-Amplier-registration.jsp
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and
have your provider’s consent.
WARNING. E911 location information may not be provided or may be inaccurate
for calls served by using this device.
The antenna for the device has a 10 meter above ground maximum antenna height limitation when the
device is used with a handset that covers the 1710-1755 MHz band. Violation of this rule could be subject
to potential FCC enforcement action for noncompliance.
This device may be operated ONLY in a xed location for in-building use.
Operational description:
To comply with FCC NPS (Network Protection Standard) requirements: NPS and other compliance/
safeguard features for AGC and anti-oscillation have been implemented. NPS and other compliance/
safeguard features are defaulted to be “On”(in operation). NPS and other compliance/safeguard features
can not be eld recongured, disabled or removed. This Amplier is not user programmable, does not need
ne tuning or adjustment, does not require professional installation. Most wireless providers consent to
the use of signal Ampliers. Some providers may not consent to the use of this device on their network.
If you are unsure, contact your provider.
3
If you need help pls contact [e-mail] and we will help
you determine your cell tower location and get you setup.
3
If you need help pls contact [e-mail] and we will help
you determine your cell tower location and get you setup.
1) Installation:
Connect the inside antenna and the outside antenna as shown in Fig. 1, Pg. 4.
2) Outside antenna:
a) Place outside antenna outside of the house in the area that has the best signal.
b) If outside location is unavailable, place the outdoor antenna on a window with
the best signal.
3) Inside Antenna: Connect the inside antenna as shown in Fig. 1, Pg. 4.
4) Separation: Increase the distance of the outside and inside antenna as much as
possible to maximize coverage and avoid gain reduction.
5) Power: Connect the power supply to the Amplier and turn it on.
6) Coverage: Use your cell phone to determine if coverage is OK. If coverage is not
adequate, please look at the Green and Orange lights to determine if the
Amplier has automatically turned down its gain per LED Gain Chart on Pg. 6.
If so pls try to separate or move antennas as per explantion on Pg. 5/6.
Important: Use only the power supply included with the Amplier. Connecting any other power supply at any
time will result in damage to the Amplier and will void the warranty. Do not turn on the power switch until
ALL cables have been screwed or plugged into the Amplier or you can cause damage to the Amplier.
Optional Dual Inside Antenna Installation (Fig. 2)
(Additional parts required which are not included in Amplier kit
See page 2 for list of approved equipment )
1) Choose a splitter model for your needs. For 2 interior antennas use a 2 way
splitter and for 3 interior antennas use a 3 way splitter etc…
2) Mount the interior antennas in the areas which need Mobile coverage
3) Evenly distribute the antennas throughout the oors and areas to cover
4) Turn on Amplier unit and check signal strength improvement as needed
1) Choose a splitter model for your needs. For 2 interior antennas use a 2 way
splitter and for 3 interior antennas use a 3 way splitter etc…
2) Mount the interior antennas in the areas which need Mobile coverage
3) Evenly distribute the antennas throughout the oors and areas to cover
4) Turn on Amplier unit and check signal strength improvement as needed
Typical Installation (Fig. 1 )
(All parts are included in Amplier kit.)
Optional Dual Inside Antenna Installation (Fig. 2 )
(Additional parts required which are not included in Amplier kit.)
Fig. 1
Fig. 2

Band Frequency
RX High Power Attenuation
Oscillation Attenuation
Orange LED
Green LED
Hp Att
Osc Att
Understanding the LED Indicators
The LED lights on the Amplier face plate indicate the operating gain state
of the Amplier.
The Green and Orange lights indicate the gain status in each operating band
When Both Green and Orange LED's are“SOLID ON” it means that the Amplier
is operating normally with full gain (No Automatic Gain Reduction)
When one or both of the LEDS are ashing (Per the chart on Pg. 6)
it indicates that the gain has been automatically reduced due to either:
A) High RX outside signal level (close to cell tower)
B) Loop Oscillation, caused when the inside antenna is located too close to the
outside antenna.
Band 20 800MHz
Band 8 900MHz
Band 3 1800MHz
Band 1 2100MHz
[e-mail]
LED Lights Explanation and Troubleshooting
Each ash indicates 3dB of gain reduction also known as gain attenuation.
For example: three ashes equals 9dB of attenuation.
Green LED indicates loop oscillation status. When ashing it means reduction of
gain. To improve you need to spread the distance between the inside and outside
antennas. If you spread them far enough away, the Green LED
will become SOLID ON.
Orange LED indicates RX (outside signal) status.
There are 5 Orange LED lights: 700 Mhz Lower, 700 Mhz Upper, 850 Mhz,
1700/2100 Mhz,1900 Mhz ext. LED ON state indicates that the RX (Receive Signal)
function of the band is functioning normally.
LED OFF state indicates that the band is shut down.
When Orange LED is ashing it indicates reduced gain also known as attenuation
of gain. You cannot prevent this condition. It means that the outside signal is very
strong and the Amplier has reduced it's gain in order to protect the closest cell
tower. If the cell tower which is close is the one you are using, then you can ignore
the gain reduction and you will still get enough signal strength to cover your area.
In this case this is the normal operating process.
If the close cell tower is not the one you are using, then you can try to relocate
your outside antenna away from this cell tower and face it or point it to the cell
tower you are using in order to get more gain.
If you need help pls contact [e-mail] and we will help
you determine your cell tower location and get you setup.
Power supply 120V AC/DC
Gain
65
60
24.0
24.0
0.0
0.0
Operating temp
-30 C + 85 C
Dimensions Weight 0.660 kg
L 12.7 x W 12.0 x H 3.2 (cm)
Model
70
24.0
0.0
BBEUZ470
BBEUZ465
BBEUZ460
SPECIFICATIONS Stealth Z4 4G LTE 2G, 3G, 3G+, 4G, 4G+, GSM, HSPA, CDMA, LTE, LTE A
Frequencies MHz
Max Power TX: dBm
Max Power RX: dBm
1
ContentsContents
SRBL1
Power supply Mobile Amplifier
Inside antenna
SEMDA2 SEMOSEMDP1
Optional outside antennas
To comply with European rules, this Amplifier must only be operated with cables, antennas
and coupling devices that have been approved for use with this equipment.
NOTE:
Only one of the outside antennas is included in this kit. All kits include necessary brackets and co-axial cables for assembly.
It is normal for the Amplier to be quite warm while the phone is in use state. All parts shown are not included in all kits.
Please check your model number for more details at smoothtalker.com
6
2
5
LED Lights Status Explanation
ON ON
ON
SLOW FLASHING
SOLID ONSOLID ON
SOLID ON
SOLID ONSLOW FLASHING
FAST FLASHING
OFF
ON/
ORANGE LED
High Power
GREEN LED
Oscilation
Attenuation (Att)
Orange Solid ON = Full Gain & Green Solid ON = Full Gain
Orange Solid ON & Green Slow Flashing = Oscillation Att
Orange O & Green Fast Flashing = Oscillation Shutdown
Orange Slow Flashing & Green Solid ON = RX High Power Att
Each ash indicates up to 3dB of gain reduction also known as gain attenuation.
For example: three ashes equals 9dB of attenuation.
No Flashing = Full Gain
Each Flash = up to 3dB of gain reduction
Each Flash = up to 3dB of gain reduction
Fast Flashing = Amplier shutdown (pls troubleshoot)
For specications of any of the Smoothalker European approved part numbers
listed below visit smoothtalker.com
European requirements prohibit the use of unauthorized Antennas, Cables,
and/or Coupling devices.
You MUST operate this device with approved antennas and cables as specied by
the manufacturer. Antennas MUST be installed at least 8 inches from any person.
You MUST cease operating this device immediately if requested by the European
or a licensed wireless service provider.
Approved Equipment List
ANTENNA CABLES
ACX100X, ACX900X
CBXmaXfe10,20,30,40,50,60
CBNmaNfe10,20,30,40,50,60
CBGmaGfe 10,20,30,40,50,60,70,80,90,100
CBL4maL4fe 10,20,30,40,50,60,70,80,90,100
SPLITTERS
ADCSPN2
ADCSPN3
ADCSPN4
ADCSPG2
ADCSPG3
ADCSPG4
ANTENNAS
SEM2THL, 11THL, 14THL, 26THL series
SRP1X , SRP1XL
SRBL series
SEMD1 series
SEMDA2 series
SEMO series
SEMDP1 series
SEMDY series
SEMDYD series
Smoothtalker®
Stealth Z460 4G LTE
Mobile
Signal Amplifier
High Power
Home/Office - High Power
4 BAND
MULTI BAND
High Power 60dB
RX/TX
BAND FREQUENCY
Hp Att
Osc Att
2G, 3G, 3G+, 4G, 4G+
GSM, HSPA, CDMA, LTE, LTE A
Band 1 2100MHz
Band 3 1800MHz
Band 8 900MHz
Band 20 800MHz
DC 6V Only Outside Antenna
Inside Antenna
stealth
tech
®
2100MHz 1800MHz 900MHz 800MHz