steel Genesi GK120 User manual

INSTRUCTION MANUAL
Exhaust / recirculating hood
GB

Contents 1
GENERAL SAFETY GUIDELINES............................................................................... 3
ELECTRICAL SAFETY................................................................................................. 3
PROPER USE .............................................................................................................. 4
ECOLOGICAL DISPOSAL ........................................................................................... 4
REFERENCE STANDARDS ........................................................................................ 4
COMPONENTS ............................................................................................................ 5
DIMENSIONS ............................................................................................................... 6
ASSEMBLY .................................................................................................................. 7
Minimum distance from cooktop.............................................................................. 7
Removing the chimney from the hood (GK and AK hoods only) .............................8
Removing the metallic filters...............................................................................8
Removing the chimney ....................................................................................... 8
Hood assembly ........................................................................................................ 9
Chimney assembly ................................................................................................ 10
Refitting the metallic filters..................................................................................... 10
Plastic reducer ....................................................................................................... 10
ELECTRICAL CONNECTIONS .................................................................................. 11
TEST........................................................................................................................... 11
OPERATION............................................................................................................... 12
Electronic control panel ......................................................................................... 12
On/off button ..................................................................................................... 12
Increase button ................................................................................................. 12
Decrease button ............................................................................................... 12
Intensive operation ........................................................................................... 12
Timed switch-off and filter saturation alarm ...................................................... 12
Light button ....................................................................................................... 12
TIPS............................................................................................................................ 13
Exhaust hood with outside discharge ....................................................................13
Recirculating range hood with filter ....................................................................... 13
CLEANING OF THE HOOD ....................................................................................... 14
Charcoal filters....................................................................................................... 14
Metal grease-trapping filters .................................................................................. 14
Cleaning the stainless steel surfaces ....................................................................14
Cleaning the polished surfaces ............................................................................. 14
Cleaning the inside of the appliance...................................................................... 14
Cleaning the control panel ..................................................................................... 14
LAMP REPLACEMENT .............................................................................................. 15
ACCESSORIES ON REQUEST ................................................................................. 16
Coloured edge (type GK hoods only) ....................................................................16
Active charcoal filters............................................................................................. 16
Models with square filter (type K hoods) ..........................................................16
Models with round filter (type GK and AK hoods).............................................16
TROUBLESHOOTING................................................................................................ 17

2 General informations
Thank you for choosing this
product...
... dedicated to real lovers of cooking.
Our goal has always been to promote a culture
of good taste, attention to detail, and a refined,
stylish design for the kitchen.
This appliance's power, reliability, ease of use
and easy cleaning, teamed with its elegant
appearance, make it one of a kind. Its
exceptional performance is comparable only
with professional equipment because it is
designed with solid criteria aimed at
productivity, safety and ergonomics and is built
with superior quality materials.
It is our sole desire to share with you our
passion for cooking with art, style and
elegance.
Manual sections
General information. Product presentation, structure of
the use manual, explanation of the symbols used and
important notices on operator safety, product integrity
and the validity of the warranty.
Warnings. General regulations regarding the safety of
operators and correct appliance use.
Installation. Instructions for the qualified technician in
charge of installing, connections, commissioning and
testing the appliance.
Use. Description of controls, switching on the appliance
and tips.
Cleaning and Maintenance. Recommended cleaning
procedures and useful advice for ensuring the appliance
continues to work efficiently and look good over time.
Special maintenance. Maintenance, repairs and
checks to be carried out only when required and with the
assistance of a qualified technician.
Accessories. Description, installation and use of the
accessories supplied with the equipment or on request.
Symbols used
Important note. Failure to comply may cause
danger that may jeopardise the user's health and
the integrity of the equipment.
Correct procedure. Compliance is strongly
recommended.
Original spare parts. The use of original spare
parts ensures the equipment performs reliably
over time.
Disclaimer
• This equipment is designed for domestic use only, not
for professional use.
• The use in a professional setting or any other use
considered improper cause the immediate decline of
the guarantee.
• The appliance meets the conformity requirements of
current EC standards.
• This manual is an integral part of the purchased
product, It should be preserved for the product’s entire
lifespan.
• Before using the product, we recommend carefully
reading this manual and all the instructions it contains.
• These instructions are valid solely for the countries the
symbols of which are shown on the cover page.
• The appliance must be installed by qualified personnel
in accordance with current regulations.
• The manufacturer is not liable for any inaccuracies in
this booklet resulting from printing or transcription
errors. The manufacturer reserves the right to modify
its products as it considers necessary or in the interests
of the user, without compromising their essential safety
and operating characteristics.

Warnings 3
General safety guidelines
• DO NOT LEAVE PACKING RESIDUE UNATTENDED AROUND
THE HOME.
• SEPARATE OUT THE VARIOUS WASTE MATERIALS AND TAKE
THEM TO THE NEAREST RECYCLING CENTRE.
• THE TECHNICAL SPECIFICATIONS OF THE APPLIANCE ARE
SHOWN ON THE RATING PLATE LOCATED INSIDE THE RANGE
HOOD. MAKE SURE THE MAINS VOLTAGE CORRESPONDS TO
THE VALUES ON THE RATING PLATE.
• INSTALLATION AND SERVICING SHOULD BE CARRIED OUT BY
QUALIFIED PERSONNEL IN ACCORDANCE WITH CURRENT
REGULATIONS.
• DO NOT CONNECT THE APPLIANCE TO FLUES (FROM
BOILERS, FIREPLACES, ETC.).
• ENSURE THERE IS ADEQUATE VENTILATION OF THE ROOM
WHEN THE RANGEHOOD IS USED AT THE SAME TIME AS
APPLIANCES BURNING GAS OR OTHER FUELS. ENSURE THAT
ALL REGULATIONS CONCERNING THE DISCHARGE OF
EXHAUST AIR HAVE BEEN FULFILLED BEFORE YOU USE THE
APPLIANCE.
• ALWAYS ENSURE THE ROOM IS SUFFICIENTLY VENTILATED
WHEN THE EXTRACTOR HOOD AND GAS-FIRED APPLIANCES
ARE USED AT THE SAME TIME.
• BEFORE OPERATING THE APPLIANCE IT IS ESSENTIAL TO
REMOVE THE PROTECTIVE FILM FROM THE INTERIOR AND
EXTERIOR.
• IMMEDIATELY AFTER INSTALLATION, TEST THE APPLIANCE
BRIEFLY USING THE DIRECTIONS FOR USE. IF IT FAILS TO
WORK, CONTACT YOUR NEAREST TECHNICAL SERVICE
CENTRE. NEVER ATTEMPT TO REPAIR THE APPLIANCE.
• THE MAXIMUM WEIGHT OF ANY OBJECT PLACED ABOVE THE
HOOD, OR HUNG TO IT (IF POSSIBLE) MUST NOT EXCEED 1,5
KILOS.
Electrical safety
• THE APPLIANCE MUST BE INSTALLED BY QUALIFIED
PERSONNEL, IN ACCORDANCE WITH THE STANDARDS IN
FORCE. IF THE SUPPLY CORD IS DAMAGED, IT MUST BE
REPLACED BY THE MANUFACTURER, ITS SERVICE AGENT OR
SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A
HAZARD. ANY MODIFICATIONS THAT MAY BE REQUIRED TO
THE ELECTRICAL SYSTEM FOR THE INSTALLATION OF THE
RANGE HOOD MUST ONLY BE MADE BY QUALIFIED
ELECTRICIANS. IT IS DANGEROUS TO MODIFY OR ATTEMPT
TO MODIFY THE CHARACTERISTICS OF THIS SYSTEM. IN THE
EVENT OF MALFUNCTIONS OR IF REPAIRS ARE REQUIRED TO
THE APPLIANCE, DO NOT ATTEMPT TO SOLVE THE PROBLEMS
DIRECTLY. REPAIRS PERFORMED BY UNQUALIFIED PERSONS
MAY CAUSE DAMAGE. FOR ALL REPAIR AND OTHER WORK ON
THE APPLIANCE, CONTACT AN AUTHORISED SERVICE/SPARE
PARTS CENTRE.
• THE EARTH CONNECTION IS OBLIGATORY CONFORMING TO
THE MODALITIES ENVISAGED BY THE SAFETY STANDARDS OF
THE ELECTRICAL WIRING SYSTEM. THE ELECTRICAL SYSTEM
FEATURES AN EARTH CONNECTION IN COMPLIANCE WITH
INTERNATIONAL SAFETY STANDARDS; FURTHERMORE, IT IS
COMPLIANT WITH THE EUROPEAN STANDARD FOR
ELECTROMAGNETIC COMPATIBILITY.
• ALWAYS CHECK THAT ALL THE ELECTRICAL PARTS ARE OFF
WHEN THE APPLIANCE IS NOT BEING USED.
• THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE
AND THE RELATIVE SOCKET MUST BE THE SAME TYPE AND
MUST COMPLY WITH CURRENT STANDARDS. AFTER
INSTALLING THE APPLIANCE MAKE SURE THAT THE PLUG IS
ACCESSIBLE TO ALLOW THE PERIODICAL CHECK-UP. DO NOT
PULL OUT THE PLUG BY PULLING THE CABLE.
• BEFORE DOING ANY WORK INSIDE THE RANGE HOOD,
DISCONNECT THE APPLIANCE FROM THE MAINS POWER
SUPPLY. CHECK THAT THE WIRES INSIDE THE RANGE HOOD
ARE NOT DISCONNECTED OR CUT; IF THIS IS THE CASE,
CONTACT YOUR NEAREST SERVICE CENTRE.
• DO NOT USE REDUCERS, ADAPTERS OR SHUNTS.

4 Warnings
Proper use
• THE APPLIANCE IS DESIGNED TO BE USED BY ADULTS ONLY.
DO NOT ALLOW CHILDREN TO APPROACH THE APPLIANCE OR
USE IT AS A TOY.
• NEVER COOK ON "OPEN" FLAMES UNDER THE RANGE HOOD.
CHECK DEEP-FRYERS DURING USE: SUPERHEATED OIL MAY
BE FLAMMABLE.
• DO NOT USE METAL SPONGES OR SHARP SCRAPERS ON THE
EXTERNAL SURFACES. FOR CLEANING USE NORMAL NON-
ABRASIVE PRODUCTS, WITH WOODEN OR PLASTIC UTENSILS
IF NECESSARY. RINSE THOROUGHLY AND DRY WITH A SOFT
CLOTH.
• CARRY OUT MAINTENANCE ON THE FILTERS AS AND WHEN
RECOMMENDED IN THE RELEVANT SECTION OF THIS MANUAL
REGARDING HOOD MAINTENANCE AND CLEANLINESS.
Ecological disposal
• THE PRODUCT PACKING IS MADE OF NON-POLLUTING,
ENVIRONMENT FRIENDLY AND RECYCLABLE MATERIALS.
DISPOSE OF THE PACKING CORRECTLY AT RECYCLING AND
DISPOSAL CENTRES.
• THE SYMBOL INDICATES THAT THIS APPLIANCE MAY NOT
BE TREATED AS HOUSEHOLD WASTE. INSTEAD IT SHALL BE
HANDED OVER TO THE APPLICABLE COLLECTION POINT FOR
THE RECYCLING OF ELECTRICAL AND ELECTRONIC
EQUIPMENT. FOR MORE DETAILED INFORMATION ABOUT
RECOVERY AND RECYCLING OF THIS PRODUCT, PLEASE
CONTACT YOUR LOCAL CITY OFFICE, YOUR HOUSEHOLD
WASTE DISPOSAL SERVICE OR THE SHOP WHERE YOU
PURCHASED THE PRODUCT.
Reference standards
• THIS PRODUCT CONFORMS TO THE REQUIREMENTS OF THE
FOLLOWING EUROPEAN DIRECTIVES:
• 2006/95/CE FOR "LOW VOLTAGE".
• 2004/108/CE FOR "ELECTROMAGNETIC DISTURBANCE".
• 2002/95/CE (ROHS - REDUCTION OF HAZARDOUS
SUBSTANCES) ON RESTRICTING THE USE OF HAZARDOUS
SUBSTANCES IN MANUFACTURING MATERIALS.
• 2002/96/CE, WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT (WEEE). BY ENSURING THIS PRODUCT IS
DISPOSED OF CORRECTLY, YOU WILL HELP PREVENT
POTENTIAL NEGATIVE CONSEQUENCES FOR THE
ENVIRONMENT AND HUMAN HEALTH, WHICH COULD
OTHERWISE BE CAUSED BY INAPPROPRIATE WASTE
HANDLING OF THIS PRODUCT.

Installation 5
Components
The packing contains the following components:
• an extraction/filtration hood;
• a chimney complete with extension;
• one or two wall mounting bars, depending on hood
type;
• two or four 8 mm toggle bolts with screws, depending
on hood type;
• four 6 mm toggle bolts with screws;
• ten self-tapping screws;
• plastic reducer with 12 cm diameter;
• this use manual.
12 cm
12 cm
12 cm
MANUALE D’USO
MANUALE D’USO
MANUALE D’USO
K
GK
AK

6 Installation
Dimensions
200
550 - 1100
300 - 600
300 - 600
400
500
200
400
500
700 / 900 / 1000 / 1172
580
350
350
260
260
250
300
550
500
700 / 900 / 1000 / 1200
700 / 900 / 1000 / 1200
Type K
Type GK
Type AK

Installation 7
Assembly
Minimum distance from cooktop
The minimum distance between the gas cooktop and
the bottom of the hood must be at least 750 mm. If the
gas cooktop manual specifies a greater distance, this
should be taken into account.
At horizontal sections, the pipe must be slightly tilted
upwards (about +10%) to allow the extracted air to exit
more easily.
Keep the number of bends to a minimum and check that
pipes are the minimum essential length.
A
G
B
C
D
E
F
A
G
B
C
D
E
F
750 mm 750 mm
Exhaust hood with outside discharge Recirculating range hood with filter
A TOP SECTION C FUME EXHAUST E HOOD UNIT G COOKING UNIT
B CENTER SECTION D FAN EXHAUST F METAL FILTERS

8 Installation
Removing the chimney from the hood
(GK and AK hoods only)
In "type K" hoods, the chimney is packed next to
the hood; in "type GK" hoods, the chimney is
secured in the interior compartment and turned
90°(fig. 1); in "type AK" hoods, the chimney is
secured in the interior compartment, in a central
position in front of the suction motor (fig. 2).
Removing the metallic filters
• Lower the splines "A1" and pull the filters "A"
downwards.
• Keeping the filters tilted down, remove them by pulling
out.
The connector "B" is now accessible. In "type GK"
and "type AK" hoods (figure 2), the connector "B"
should be released from the suction motor to allow
the removal of the plastic reducer "E".
Removing the chimney
• Unscrew the screws "C" to free the chimney "D".
• Take out the chimney "D", complete with extension,
from the hood compartment.
B
C
D
D
C
A
A
C
C
E
A1
12 cm
Fig.1
Fig.2

Installation 9
Hood assembly
• Rest the mounting bar "A" against the wall, at a height
determined by the sum of the 750 mm distance from the
cooktop + the "h" value relating to the relevant model of
hood.
• "Type K" hood: h = 520 mm
• "Type GK" hood h = 357 mm
• "Type AK" hood: h = 413 mm
• Check the horizontal alignment with a spirit level and
mark the 2 holes to be drilled at the ends of the bar.
• Drill the holes, insert 2 x 8 mm dia. screw anchors, and
fasten the bar using the corresponding screws.
• Hook the range hood to the support bar.
• Adjust the alignment of the range hood using the
screws on the brackets. The top screw “B” adjust the
distance from the wall, the bottom screw “C” adjust the
height.
• Fasten the bottom of the hood to the wall with the
screws and two 6 mm bolts using the holes "F".
• For extractor hoods: connect pipe "E" (not supplied)
coming from the duct hole to union "D".
520 mm750 mm
750 mm
750 mm 357 mm
413 mm
A
AA
AA
B
C
h
750 mm
E
D
A
F

10 Installation
Chimney assembly
• Move part "G" towards the hood until fully inserted.
• Screw part "G" to the hood using the self-tapping
screws "N".
• Slide the telescopic component "H" to reach the
required height.
• Mark the wall at the position of the two holes "Q" in the
mounting bar "L".
• Lower the telescopic component "H" and remove the
mounting bar "L" by unscrewing the two screws "M".
• Move the mounting bar "L" to the wall in line with the
previously marked holes.
• Use a spirit level to check the horizontal alignment and
drill the holes.
• Insert two 6 mm toggle bolts and fasten the mounting
bar "L" to the wall.
• Screw the telescopic component "H" to the mounting
bar "L" with the screws "M".
If previously disconnected, reconnect the
connector "B" to the suction motor.
Refitting the metallic filters
Reposition the filters by introducing first the guides "P"
into the rear slots, then push the filters up and lock them
in position by closing the splines "A".
Plastic reducer
The motor exhaust union has a diameter of 15 cm. The
hoods are fitted with a 12 cm plastic reducer.
L
QQ
MM
H
H
G
G
N
M
L
M
B
A
P
12 cm

Installation 11
Electrical connections
The connections must be performed in
compliance with the legal standards in force.
Check that the relief valve and the electrical
system are able to support the load of the
appliance.
The equipment is not fitted with plugs.
The yellow/green earth wire must not be
disconnected by the switch.
The technical specifications of the appliance are
shown on the rating plate located inside the range
hood. Make sure the mains voltage corresponds
to the values on the rating plate.
Use plugs conforming to current electrical standards,
taking into account that:
• the yellow-green wire must be used for the earth;
• the blue wire must be used for the neutral;
• the brown wire must be used for the phase; the cable
must not come into contact with hot parts (over 75°C);
• fit a plug that is suitable for the load to the power cable,
and connect it to a suitable power outlet.
Before plugging in the appliance, check that:
• the power voltage corresponds to that indicated on the
specification plate;
• the earth connection is correct and operational;
• the power supply system has an effective earth
connection according to current legislation;
• the socket or the omnipolar switch used are within easy
reach when the appliance is installed.
Test
Check:
• that the duct and external outlet are not blocked;
• the metallic and active charcoal filters (if fitted) are
positioned correctly. Refer to section “Active charcoal
filters” on p. 16.
Connect the hood to the electric supply, switch on the
motor as described in section “Operation” on p. 12 and
check:
• the correct operation and suction capacity at all
selectable speeds;
• the correct operation of the lights.

12 Use
Operation
Electronic control panel
The hood has three different suction speeds plus one for
intensive operation.
On/off button
Press this button to start or stop suction.
The hood will operate at the speed selected before last
switching off.
Increase button
Press this button to go to the next suction speed.
Decrease button
Press this button to return to the previous suction speed.
Speeds 1, 2 and 3 can be seen by the number of
lit buttons, not including the light and timed switch-
off buttons.
Intensive operation
On pressing the increase button three times, the hood
enters intensive operation mode (the button flashes).
Intensive operation is timed and the motor returns
automatically to the 3
rd
speed after about 15 minutes.
Timed switch-off and filter saturation alarm
Press this button to automatically switch off the hood
after 15 minutes of operation. The button will flash red
until the suction motor switches off.
After about 30 hours of operation a warning light
automatically appears to indicate the metallic filters
should be cleaned (the button is lit with a steady red light
even when the motor is off). Clean the metallic filters as
described in section “Metal grease-trapping filters” on
page 14.
To deactivate the warning light, hold the button down for
a few seconds.
Light button
Press this button to switch the lights on and off.
1 2 3

Use 13
Tips
The range hood should be switched on when starting to
cook, and left on until the odours disappear.
Exhaust hood with outside discharge
In this version, the fumes and steam from the kitchen are
conveyed outside through an exhaust duct. The exhaust
conveyor that protrudes from the upper part of the range
hood must be connected to a duct that carries the fumes
and steam outside.
Active charcoal filters are not used for this type of
operation, as exhaust air is not reintroduced into
the kitchen.
Always ensure the room is sufficiently ventilated
when the extractor hood and gas-fired appliances
are used at the same time.
Recirculating range hood with filter
In this version, the air passes through charcoal filters
(available on demand) for purification, and is then
recirculated back into the kitchen. Check that the
charcoal filters are fitted to the motor, and if not, install
them as described in the instructions “Active charcoal
filters” at page 16.
FIRST SPEED (decrease button lit): to maintain clean air in the kitchen with low
electric consumption.
SECOND SPEED (decrease and on/off buttons lit): for normal cooking.
THIRD SPEED (decrease, on/off and increase buttons lit): to eliminate strong odours
and steam from the kitchen.
INTENSIVE OPERATION (decrease and on/off buttons lit, increase button flashing):
for use to eliminate very strong odours or excessive amounts of steam or to quickly
eliminate particularly persistent cooking fumes. Intensive operation deactivates
automatically after 15 minutes.

14 Cleaning and Maintenance
Cleaning of the hood
Regular maintenance ensures the hood will run
efficiently over time. Particular attention should be paid
to the metallic and active charcoal filters. Cleaning the
filters and relative supports frequently will prevent the
build-up of grease and grime. These substances, in
addition to reducing the hood's performance, can be a
fire hazard.
Before performing any cleaning or maintenance
operations, disconnect the appliance by
unplugging it or using the main switch.
Do not clean the surfaces of the appliance when
they are still hot.
Use only suitable detergents to clean the surfaces
of the appliance. The manufacturer declines all
responsibility and is not liable for damage arising
from the use of unsuitable and/or other detergents
than those indicated.
Do not use pressure or steam spray guns to clean
the appliance.
Do not use liquids or solvents on electrical parts or
close to the suction motor.
Charcoal filters
These trap the odours present in the stream of air that
passes through them. The air is purified by passing a
number of times through the filters and being
recirculated into the kitchen. The charcoal filters cannot
be cleaned, and should be replaced on average every 3-
4 months (according to use). To replace the charcoal
filters, see the instructions “Active charcoal filters” on
page 16.
Metal grease-trapping filters
These trap the fat and grease particles suspended in the
air, and therefore should be washed every month in hot
water and detergent, without bending them. To remove
the metallic filters, see the instructions in section
“Removing the metallic filters” on page 8. Wait until they
are completely dry before repositioning them.
Cleaning the stainless steel surfaces
To clean and preserve the stainless steel surfaces, use
a solution of warm water and vinegar or neutral soap.
Pour the solution onto a damp cloth and wipe the steel
surface, in the direction of the satin finish, rinse
thoroughly and dry with a soft cloth or chamois leather.
Do not under any circumstances use metallic sponges or
sharp scrapers that may damage the surfaces. Only use
non-scratch, non-abrasive sponges and, if necessary,
wooden or plastic utensils.
Cleaning the polished surfaces
Clean with a non-abrasive, scratchproof sponge
dampened with warm water and neutral soap or with a
standard detergent for polished surfaces. Rinse and dry
carefully with a soft cloth.
Abrasive pastes, coarse wire pads, steel wool or acid will
damage the surfaces. Do not use alcohol.
Cleaning the inside of the appliance
The interior parts of the hood do not require any routine
cleaning.
Cleaning the control panel
Clean the control panel with a damp cloth

Special maintenance 15
Lamp replacement
Make sure the appliance is disconnected from the
mains power supply.
Light bulbs with different shapes and power
ratings from the original may seriously damage the
light compartment.
• Remove, by levering with a screwdriver, the support
ring “A” for the cover glass.
• Remove the cover glass “B” to access the light
compartment.
• Replace the lamp with the same type (halogen max
20 W - 12 Volt, G4 fitting).
• Replace the glass cover “B” and fasten it using the
special ring “A”.
Model with "Square halogen light":
• Completely open the panel to a 90°angle (see figure)
by pressing PUSH.
• Replace the lamp with the same type (halogen max
20 W - 12 Volt, G4 fitting).
• Close the panel correctly.
A
B

16 Accessories
Accessories on request
Make sure the appliance is disconnected from the
mains power supply.
Coloured edge (type GK hoods only)
Front moulding in painted steel available in a variety of
colours.
• Remove the metallic filters "A".
• Unscrew the ten screws "B" from inside the hood.
• Remove the standard edge.
• Replace with the new edge "C", making sure the control
panel "D" is correctly fitted in the edge frame.
• Tighten the ten screws "B".
• Reposition the metallic filters "A".
Active charcoal filters
Two types of active charcoal filters are available,
depending on the hood model.
Models with square filter (type K hoods)
• Remove the metallic filters.
• Place the nut "F" above the filter housing slot.
• Position the filter “B” in the housing and fasten it by
screwing knob "C" in nut "F".
• Reposition the metallic filters.
Models with round filter (type GK and AK hoods)
• Remove the metallic filters.
• Rest the filters on the motor (one on each side), taking
care to place the pins close to hooks "E" on the motor.
• Turn the filters clockwise until properly hooked on.
• Reposition the metallic filters.
Contact your distributor to order new active
charcoal filters.
AC
D
B
B
F
C
F
E
E
E

Troubleshooting 17
Troubleshooting
If the equipment is not working properly, consult the
following table of possible causes and recommended
remedies before contacting Customer Service.
If the cause of the problem cannot be found,
switch off the equipment, remove the plug and
contact Customer Service.
PROBLEM POSSIBLE CAUSES AND RECOMMENDED REMEDY
The suction motor does not start when the on button is
pressed.
The plug is not connected to the socket or there is a
mains failure.
The electrical connector on the suction motor is
disconnected.
The suction motor starts, but the lights do not switch on
when the lights button is pressed.
Bulbs blown. Replace them.
Bulbs not fully inserted.
Transformer faulty. Contact Customer Service.
The motor starts but cooking fumes are not extracted. Metallic or active charcoal filters clogged. Clean metallic
filters or replace the active charcoal filters. Disconnect
the hood from the mains before accessing internal parts.
Duct clogged.
The suction motor stops suddenly after running for a
few minutes.
This is normal if the timed switch-off has been activated.
When the motor is off the timed switch-off button is lit
with a red light.
This is normal after 30 hours of operation. The warning
light (steady red light) signals the need to clean the
metallic filters. To eliminate the filter saturation warning
light, simply hold the button down for a few seconds.

B00090 ZS5077 08/14