Stephen SVG200SP PLUS User manual

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 1 / 36 www.step en-tele.com
SVG200SP+
1 FXS + 1 PSTN SIP/IAX ATA User Manual
STEPHEN TECHNOLOGIES CO.,LIMITED
ALL RIGHTS RESERVED

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 2 / 36 www.step en-tele.com
1 SVG200SP+ Features ............................................................................................... 4
1.1 Appearance ................................................................................................................... 4
1.2 Interface ........................................................................................................................ 4
1.3 Electricity c aracteristic ................................................................................................ 4
1.4 Software ........................................................................................................................ 4
1.5 Standard and Protocols ................................................................................................. 5
1.6 Compliant Standards ..................................................................................................... 5
1.7 Operating requirement ................................................................................................. 6
1.8 Package.......................................................................................................................... 6
1.9 Installation ..................................................................................................................... 7
2 Web Configuration .................................................................................................. 7
2.1 Access Web setting page ............................................................................................... 7
2.2 Current state ................................................................................................................. 8
2.3 Network ......................................................................................................................... 9
2.3.1 Wan Config ........................................................................................................ 9
2.3.2 LAN Config ....................................................................................................... 10
2.4 VoIP ............................................................................................................................. 10
2.4.1 SIP Config ............................................................................................................... 10
2.4.2 Iax2 Config .............................................................................................................. 11
2.5 Advance ....................................................................................................................... 13
2.5.1 DHCP Server .................................................................................................... 13
2.5.2 NAT .................................................................................................................. 14
2.5.3 Net Service ...................................................................................................... 15
2.5.4 QoS settings ..................................................................................................... 16
2.5.5 Advance SIP settings ........................................................................................ 17
2.5.6 Digital Map ...................................................................................................... 18
2.5.7 Call Service Settings......................................................................................... 19
2.5.8 MMI Filter ....................................................................................................... 19
2.5.9 Audio Settings ................................................................................................. 20
2.5.10 VPN .................................................................................................................. 20
2.6 Dial-Peer Settings ........................................................................................................ 21
2.7 Config Manage ............................................................................................................ 21
2.8 Update ......................................................................................................................... 22
2.9 System Manage ........................................................................................................... 24
2.9.1 Account Manage ............................................................................................. 24
2.9.2 Syslog Config: .................................................................................................. 24
2.9.3 Time Set: ......................................................................................................... 25
2.9.4 Logout&Reboot ............................................................................................... 25
3 IVR setting ............................................................................................................. 26
4 Telnet Console ....................................................................................................... 27
4.1 Introduce ..................................................................................................................... 27
4.2 Global Command......................................................................................................... 28
5 Tree Structure ....................................................................................................... 28
6 Network Diagnosis ................................................................................................ 29
7 Restore to factory default ..................................................................................... 29
8 POST Mode(safe mode) ........................................................................................ 30
9 FAQ ........................................................................................................................ 30
How many SIP servers may SVG200SP+ register simultaneously? .................................. 30

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 3 / 36 www.step en-tele.com
How can I know t e SVG200SP+’s IP address? ................................................................ 30
How to use SVG200SP+’s Lifeline function? .................................................................... 30
W y t e settings vanis after reboot? ............................................................................ 30
How to use t e dial rule? ................................................................................................ 31
How to use speed dial function? ..................................................................................... 32
How to configure digital map? ........................................................................................ 32
How to use Call Forward, Call Transfer and 3-way Conference calls? ............................. 32
VLAN implement ............................................................................................................. 33

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 4 / 36 www.step en-tele.com
1 SVG200SP+ Features
1.1 Appearance
PWR ：
：：
： power connection status
S S : server registration status . registered: on , gliting , not-registered , off
WAN: WAN port connectiong , contected , on , offline : off
LAN: LAN port connectiong , contected , on , offline : off
PSTN: lig t on w en PSTN call come in/out
VoIP: lig t on w en VoIP call come in/out , T e default status w en pick up t e call is VoIP call out
1.2 Interface
Power: Output Power:12VDC,500mA.
Port: RJ11 port. Connect to andset or t e Lifeline accessory.
WAN: RJ45 port.
LAN: RJ45 port.
1.3 Electricity characteristic
 Speciality of electric: output t e 12V 500mA DC
 The network connects:2 RJ45 connect, a WAN, a LAN
 FXS: 2 port
1.4 Software
 Support two sip servers running at t e same time.
 Back-up sip server support.

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 5 / 36 www.step en-tele.com
 NAT, Firewall.
 DHCP client and server.
 Support PPPoE, (used for ADSL, cable modem connecting).
 Support major G7.xxx CODEC.
 VAD,CNG.
 G.165 compliant 16ms ec o cancellation
 Tone generation and Local DTMF re-generation according wit ITU-T
 E.164 dial plan and customized dial rules
 Support Lifeline.
 Hotline.
 Speed Dial
 Call Forward, Call Transfer, 3-way conference calls
 Caller ID display
 DND(Do Not Disturb),Black List,Limit List
 Upgrade firmware t roug FTP or HTTP.
 Web management.
 Reverse polarity
 Telnet remote management.
 Voice prompt
 adjustable user password and super password
1.5 Standard and Protocols
 IEEE 802.3 /802.3 u 10 Base T / 100Base TX
 PPPoE: PPP Protocol over Et ernet
 DHCP Client and Server: Dynamic Host Configuration Protocol
 G.711 u/a; G729 audio Codec
 SIP RFC3261, RFC 2543
 IAX2
 TCP/IP: Internet transfer and control protocol
 RTP: Real-time Transport Protocol
 RTCP: Real-time Control Protocol
 VAD/CNG save bandwidt
 Telnet: Internet's remote login protocol
 DNS: Domain Name Server
 TFTP: Trivial File Transfer Protocol
 HTTP: Hyper Text Transfer protocol
 FTP: File Transfer protocol
 RFC 3362 ： T.38 protocol
1.6 Compliant Standards
 CE ： EN55024,EN55022
 FCC part15
 comply wit ROHS in EU
 comply wit ROHS in C ina


SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 6 / 36 www.step en-tele.com
Explanation:
T e letter “e” is t e first letter of “environment: and “electronic”, T e rim is a round wit two arrow , stands for recycle. T e
number 20 stands for t e years of environment protection. Please note t e years of environment protection is not
discarding year nor usage life
1.7 Operating requirement
● Operation temperature: 0 to 40° C (32° to 104° F)
● Storage temperature: -30° to 65° C (-22° to 149° F)
● Humidity: 10 to 90% no dew
1.8 Package
 Size 128 x 85 x 30 mm
 Packing List
 SVG200SP+ ATA
 Power adaptor (12v, 500mA)
 Manual CD

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 7 / 36 www.step en-tele.com
1.9 Installation
Use Et ernet cable to connect SVG200SP+’s LAN port and your computer. Set your computer’s ip to t e network
192.168.10.x or using dynamic obtain IP. Open your web browser and key in 192.168.10.1. T en you will see t e logon page
of SVG200SP+, t e default username and password is admin/admin for administrator and guest/guest for guest.
Set up page for VoIP use only:
2 Web Configuration
2.1 Access Web setting page
Enter SVG200SP+ IP address in t e web browser and press ENTER to go to t e log on page, and key in t e username and
password to access SVG200SP+ setting page.
Default username and password is:
Administrator: Username: admin password: admin
User: Username: guest Username: guest

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 8 / 36 www.step en-tele.com
2.2 Current state
This page shows SVG200SP+’s running state.
Network ：
：：
： s ows t e WAN and LAN port connecting state and current settings.
VoIP ：
：：
： s ow t e default protocol, t e working state of SIP and IAX2, you can see w et er SVG200SP+ as registered t e
public sip server and IAX2 server.
Phone Number s ows t e public sip server, t e private sip server and t e IAX2 server p one numbers.

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 9 / 36 www.step en-tele.com
2.3 Network
2.3.1 Wan Config
WAN port network setting page.
Support static IP, dynamic obtain IP and PPPoE.
Configure Static IP:
----Enable Static;
----Set SVG200SP+’s IP address in t e IP Address;
----Set net mask in t e Net mask field;
----Set router IP address in t e Gateway;
----DNS Domain:
----Set local DNS server in t e Preferred DNS and t e Alternate DNS
Configure to dynamic obtain IP
----Enable DHCP;
If t ere is DHCP server in your local network, SVG200SP+ will automatically obtain WAN port network information from
your DHCP server.
Configure PPPoE:
----Enable PPPoE
----PPPoE server: Enter “ANY” if no specified from your ITSP.
----Enter PPPoE username and pin in t e username and password.
SVG200SP+ will automatically obtain WAN port network information from your ITSP if PPPoE setting and t e setup are
correct.
Notice: If user accesses t e gateway t roug WAN port. He s ould use t e new IP address to access t e gateway w en t e
WAN port address was c anged.

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 10 / 36 www.step en-tele.com
2.3.2 LAN Config
Bridge Mode: Enable t is option to switc to bridge mode. Gateway won’t assign IP for its LAN port in bridge mode and its
LAN and WAN port will be in t e same network. (T is setting won’t take effect unless you save t e config and reboot t e
device)
IP Netmask: Set t e IP and Netmask for t e LAN
DHCP Server: Enable DHCP service in LAN port
NAT: Enable NAT.
2.4 VoIP
2.4.1 SIP Config
Setting page of public SIP server:
Register Server Addr: Register address of public SIP server
Register Server Port: Register port of public SIP server
Register Username: Username of your SIP account (Always t e same as t e p one number)
Register Password: Password of your SIP account.
Proxy Server Addr: IP address of proxy SIP server (SIP provider always use t e same IP for register server and proxy
server, in t is case you don’t need to configure t e proxy server information. )
Proxy Server Port: Signal port of SIP proxy
Proxy Username: proxy server username
Proxy Password: proxy server password

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 11 / 36 www.step en-tele.com
Domain Realm: SIP domain, enter t e sip domain if any, ot erwise SVG200SP+ will use t e proxy server address
as sip domain.
Local SIP port: Local SIP register port, default 5060
Phone Number: P one number of your SIP account
Register Expire Time: register expire time, default is 600 seconds. SVG200SP+ will auto configure t is expire time to t e
server recommended setting if it is different from t e SIP server.
Detect Interval Time: Co-work wit t e Auto Detect Server, if Auto Detect Server is enable, SVG200SP+ will periodically
detect if t e SIP server is available according t is setting.
RFC Protocol Edition: Current SVG200SP+ SIP versions. Set to RFC 2543 if t e gate need to communicate to devices (suc
as CISCO5300) using t e SIP 1.0. Default is RFC 3261.
Enable Register: Enable/Disable SIP register. SVG200SP+ won’t sent register info to SIP server
DTMF Mode: DTMF signal sending mode: support RFC2833, DTMF_RELAY (inband audio) and SIP info
Auto Detect server: co-work wit Server Auto Swap and Detect Interval Time. Enable t is option, SVG200SP+ will
periodically detect w et er t e public SIP server is available, if t e server is unavailable, t e SVG200SP+ will switc to t e
back-up SIP sever, and continue detecting t e public sip server. SVG200SP+ will switc back to t e primary SIP server if t e
server is available again.
Server Auto Swap:Please refer to Auto Detect server for detail.
Enable Via rport: config t e supporting for RFC 3581
SIP(Default Protocol): Setting for t e default protocol of SIP
2.4.2 Iax2 Config
Setting page of public IAX server:
IAX Server Addr: Register address of public IAX server
IAX Server Port: Register port of public IAX server ， default port is 4569
Account Name: Username of your SIP account (Always t e same as t e p one number)
Account Password:Password of your IAX account.
Local port: Signal port of local, default port is 4569
P one Number: P one number of your IAX account
Voice mail number: If t e IAX support voice mail, but your username of t e voice mail is letters w ic you can not input
wit t e ATA , t en you use t e number to stand for your username
Voice mail text: if IAX support voice mail, config t e domain name of your mail box ere.

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 12 / 36 www.step en-tele.com
Echo test number: If t e platform support ec o test , and t e number is test form , t e config t e test number to replace
t e text format T e ec o test is to test t e woring status of terminals and platform
Echo test text: ec o test number in text format
Refresh time: IAX refres time
Enable Register: enable or disable register
IAX(Default Protocol): Set IAX 2 as t e default protocol , if not t e system will c oose SIP as default
Enable G.729: Using G.729 speec coding mandatory consultations

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 13 / 36 www.step en-tele.com
2.5 Advance
2.5.1 DHCP Server
DHCP server manage page.
User may trace and modify DHCP server information in t is page.
Update Mode: Using DHCP updated model ,None expressed are not updated, Update firmware update firmware is used to
DHCP. Update file is used to configure DHCP updated configuration files.
Tftp Server: Addresses using TFTP server upgrade 。
DNS Relay: enable DNS relay function.
User may use below setting to add a new lease table.
Lease Table Name: Lease table name.
Lease Time: DHCP server lease time.
Start IP: Start IP of lease table.
End IP: End IP of lease table. Network device connecting to t e SVG200SP+ LAN port can dynamic obtain t e IP in t e
range between start IP and end IP.
Netmask: Netmask of lease table.
Gateway: Default gateway of lease table
DNS: default DNS server of lease table.
Notice: T is setting won’t take effect unless you save t e config and reboot t e device

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 14 / 36 www.step en-tele.com
2.5.2 NAT
Advance NAT setting. Maximum 10 items for TCP and UDP port mapping.
IPSec ALG: Enable/Disable IPSec ALG;
FTP ALG: Enable/Disable FTP ALG;
PPTP ALG: Enable/Disable PPTP ALG;
Transfer Type: Transfer type using port mapping.
Inside IP: LAN device IP for port mapping.
Inside Port: LAN device port for port mapping.
Outside Port: WAN port for port mapping.
Click Add to add new port mapping item and Delete to delete current port mapping item.

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 15 / 36 www.step en-tele.com
2.5.3 Net Service
HTTP Port: configure HTTP transfer port, default is 80.User may c ange t is port to en ance system’s security. W en t is
port is c anged, please use ttp://xxx.xxx.xxx.xxx:xxxx/ to reconnect.
Telnet Port: configure telnet transfer port, default is 23.
RTP Initial Port: RTP initial port.
RTP Port Quantity: Maximum RTP port quantity, default is 200
Notice:
Settings in t is page won’t take effect unless save and reboot t e device.
If you need to c ange telnet port or HTTP port, please use t e port greater t an 1024, because ports under 1024 is system
remain ports.
HTTP service if HTTP is set to 0.

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 16 / 36 www.step en-tele.com
2.5.4 QoS settings
SVG200SP+ implement QoS based on 802.1p, T e QoS is used to mark t e network communication priority in t e data
link/MAC sub-layer. SVG200SP+ will sorted t e packets using t e QoS and sends it to t e destination.
1. Voice 802.1p Priority --- Configure t e priority of t e voice packets in 802.1p protocol.
2. VLAN Enable --- Disable/Enable VLAN function
3. Voice VLAN ID --- configure t e Voice/signaling VLAN ID
4. DiffServ Enable --- Disable/Enable Diffserv service
5. DiffServ Value --- Configure Diffserv parameter. T e value range : value range ：
0x28,0x30,0x38,0x48,0x50,0x58,0x68,0x70,0x78,0x88,0x90,0x98,0xb8.default is 0xb8 ,oxb8 stands for best fast
transmission; 28-30 is guaT rantee for t e transmission priority for t e 1st rank , 48-58 is guarantee for t e transmission
priority for t e 2nd rank, 68-78 is guarantee for t e transmission priority for t e 3rd rank, 88-98 is guarantee for t e
transmission priority for t e 4t rank.
6. Data VLAN ID--- Assign VLAN id for data stream.
7. Data 802.1P Priority --- Configure t e priority of t e data packets (non-voice/signaling data) in 802.1p protocol.
8. Data/Voice DiffServ differentiated --- undifferentiated for Date and voice VLAN is not distinction VLAN tag, Tag
differentiated for Date and Voice VLAN is distinction VLAN tag, Date untagged for Date VLAN is distinction VLAN tag
Please refer to VLAN implement for detail

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 17 / 36 www.step en-tele.com
2.5.5 Advance SIP settings
T is page is used to set t e private sip server, stun server, and back up sip server information.
STUN Server setting:
STUN Server Addr: configure stun server address;
STUN Server Port: configure stun server port default 3478
STUN Effect Time: stun detect NAT type circle, unit: minute.
Enable SIP STUN: enable/disable stun.
Please refer to sip conf for t e setting for ow to set t e public alter server.
Private Server Type ：
：：
： T e particular Private service system supplier carries out t e sign and speec es to encrypt, default is
common
User can register two sip servers: public sip server and private sip server. t ese two sip servers are independent from eac
ot er and running in t e same time.
For ow to configure private sip server. Please refer to sip configuration.

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 18 / 36 www.step en-tele.com
2.5.6 Digital Map
Digit map is a set of rules to determine w en t e user as finis ed dialing.
SVG200SP+ support below digital map:
Digital Map is based on some rules to judge w en user end t eir dialing and send t e number to t e server. SVG200SP+
support following digital map:
----End Wit “#”: Use # as t e end of dialing.
----Fixed Lengt : W en t e lengt of t e dialing matc , t e call will be sent.
----Timeout: Specify t e timeout of t e last dial digit. T e call will be sent after timeout
----Prefix: User define digital map:
[ ] represents t e range of digit, can be a range suc as [1-4], or use comma suc as [1,3,5], or use a list suc as [234]
x represents any one digit between 0~9
Tn represents t e last digit timeout. n represents t e time from 0~9 second, it is necessary. Tn must be t e last two
digit in t e entry. If Tn is not included in t e entry, we use T0 as default, it means system will sent t e number immediately
if t e number matc es t e entry.
Example:
[1-8]xxx All number from 1000 to 89999 will be sent immediately.
9xxxxxxx 8 digits numbers begin wit 9 will be sent immediately.
911 Number 911 will be sent will be immediately
99xT4 3 digits numbers begin wit 99 wit be sent after four seconds.

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 19 / 36 www.step en-tele.com
2.5.7 Call Service Settings
User configure the value add service such as hotline, call forward, call transfer, 3-way conference call .etc in this page
Hotline: configure otline number. SVG200SP+ immediately dials t is number after ook-off if it is set.
Call Forward: Please refer to value add service for detail.
No Disturb: DND, do not disturb, enable t is option to refuse any calls.
Ban Outgoing: Enable t is to ban outgoing calls.
Enable Call Transfer: Please refer to value add service for detail.
Enable Three Way Call: Please refer to value add service for detail.
Enable Call Waiting: Enable/disable Call Waiting
Accept Any Call: If t is option is disable, SVG200SP+ refuse t e incoming call w en t e called number is different from
SVG200SP+’s p one number.
No Answer Time: no answer call forward time setting.
Black List: incoming call in t ese p one numbers will be refused.
Limit List: outgoing calls wit t ese p one numbers will be refused
2.5.8 MMI Filter
MMI filter is used to make access limit to SVG200SP+ Gateway.
W en MMI filter is enable. Only IP address wit in t e start IP and end IP can access SVG200SP+ gateway.

SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual
陈泽科技有限公司 20 / 36 www.step en-tele.com
2.5.9 Audio Settings
CODEC: select t e prefer CODEC; support ulaw, alaw and G729
Signal Standard: Support CHINA, Japan and USA standard
Input Volume: Handset in volume.
Output Volume: Handset out volume.
G729 Payload Length: G729 payload lengt
VAD: Enable/disable Voice Activity Detection
FAX Mode: select t e FAX Mode
2.5.10 VPN
t is page is VPN setting page , t e Gateway support t e VPN wit UDP and L2TP protocol .T e parameters is as below
VPN IP ：
：：
： After VPN registered successfully, VPN server will give an IP aggress to t e terminal . If t ere is a IP address s own
on terminal (except for 0.0.0.0) ,it means your VPN as registered
UDP Tunnel
VPN Server Addr
：
：：
： register to t e address of VPN server 。
VPN Server Port ：
：：
： Register to t e port of VPN server