Sterling DUO User manual

1. Using a Phillips screwdriver, remove the screw from the plastic handle. Slide metal
handle tube into the plastic handle, align the holes, reinstall and tighten the screw.
2. Locate the other metal handle tube and slip the end with one hole over the plastic
handle connector on the nished handle assembly. Make sure the locking pin protrudes through the hole in
the side of the lower tube (see illustration 2).
3. Remove the screw from the black painted yoke and insert the metal handle
tube into the yoke. Reinstall the screw, and tighten (see illustration 3).
Sterling Duo High-Speed Carpet and Hard Floor Cleaner
Cleans, scrubs and polishes hard oors
Remove stains and deep clean carpets
Thank you for choosing to purchase the Sterling Duo High-Speed Carpet and Hard Floor Cleaner. This is a professional grade product
designed to clean all oor types including carpet, wood, tile, vinyl and stone. This product is intended for indoor or outdoor use. Please
assemble and operate the product in accordance with these instructions and save for future use. Use Sterling original replacement at-
tachments and accessories to ensure you are getting only the highest quality results on your oor. If you have any questions, please visit
SterlingNA.com or call our customer service department at 844-822-7787.
Assembly Instructions:
Screw
Handle
Lockpin
Yoke
Screw
Operating Instructions:
To operate, step on handle release, then tilt handle downward
to a comfortable height. The motor will activate once the han-
dle is lowered a few inches.
To Clean Hard Floors: Attach microber pads on nylon
brushes. Push exible plastic lock into center of microber pad
then onto shaft in the center of nylon brush until it is secured.
Spray your favorite cleaning solution on a small area of oor,
then make several passes with product until you achieve de-
sired results. When pads are dirty, they can be turned over, re-
attached and used again. Dirty pads can be rinsed, laundered
and reapplied to the product up to 100 times.
To Clean Heavily Soiled Hard Floors or Remove
Old Floor Wax: Attach green scrubbing pads on nylon
brushes. Secure green scrubbing pads by inserting black plastic
locking clip through center of the pad and onto shaft in center
of nylon brush.
To Polish Waxed Floors: Attach felt pads on nylon brushes. Use black plastic locking clip
in the same manner as described above for green scrubbing pads. Follow manufacturer’s instruc-
tions for applying oor wax. The felt pads are used to bu and polish the oor once the wax has
dried thoroughly.
Scrubbing Brush
Base
Handle Release
Lockpin
Cord Hooks
Screw Handle

Voltage: 120, Frequency: 60 HZ
Power Requirement: 180 Watt
Technical Information:
IMPORTANT SAFETY INSTRUCTIONS:
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT:
WARNING: To reduce the risk of re, electrical shock, or injury:
1. Never carry the product by the cord, or yank the cord to disconnect the product from an outlet, instead grasp the plug, and pull
to disconnect.
2. Keep cord away from heated surfaces. Do not pull cord around sharp edges or corners. Do not close door on the cord.
3. Do not contact moving parts.
4. Do not leave product unattended, when plugged in. Unplug from outlet when not in use, and before servicing.
5. Do not handle plug or product with wet hands.
6. Follow all label, and marking instructions.
7. Do not allow product to be used by children. Close attention is needed when product is used near children.
8. Do not use with damaged cord, or plug. If product is not working as it should, has been dropped, damaged, or dropped into
water, take it to an authorized service center.
9. Do not use with, or near ammable liquids.
10. Do not store product near hot ovens or heating appliances.
11. Use only as described in this manual. Use only manufacturer’s recommended attachments. Do not use for any purpose other
than described in this user’s guide.
12. Make sure the product is connected to the correct voltage. The correct voltage is listed on the rating label.
13. Do not attempt to repair this product yourself. If the product needs repair, take it to an authorized service center.
14. Do not submerge the product in water, or other liquid. Do not place, or store the product where it can fall, or be pulled into a
tub, sink, or other vessel containing liquid. Do not wash the product.
15. If using the product to polish oor wax, make sure the wax is completely dry before polishing.
16. The product is equipped with a thermal limiting device, to protect the motor from excessive temperature. If the product sud-
denly stops operating, unplug the product, and allow it to cool. If the product is left plugged in, it could start unexpectedly
when the motor cools.
To Remove Stains From Carpet: Use nylon brushes only. Spray an encapsulating type carpet cleaner on stain, then make several
passes with product to agitate chemical deep into carpet bers. Allow chemical to dry per manufacturer’s instruction (normally about 20
minutes), then vacuum carpet to remove encapsulated dirt.
Encapsulating carpet cleaners are highly recommended by carpet mills for removing stains and for low moisture cleaning. They can be pur-
chased at most janitorial supply stores..
To Clean Wide Areas of Carpet: Attached felt pads and carpet bonnets. Attach felt pads in the same manner described above
for polishing waxed oors. Stretch the elastic band on carpet bonnet over felt pad until it is tight and secured. Again, an encapsulating type
carpet cleaner is suggested for best results..
Operating Instructions (cont.)
7545 Irvine Center Dr., Ste. 200 •Irvine, CA 92618
Toll Free: 844 VACS R US or 844-822-7787 •Fax: [phone]
SterlingNA.com