stilum retis 1 User guide

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved State: 24.03.2017 p. 1
Mounting instruction climbing net „retis 1“
Item-No. 515515402
Diagram 1: Overall view of play equipment with description of individual elements
Sliding bars

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved State: 24.03.2017 p. 2
Mounting instruction climbing net „retis 1“
Item-No. 515515402
Foundation
Diagram 2: Rear view with dimension details „retis 1“
450400
850
A A
600
600
1355
665
1929
3310
600
600
A-A
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
retis 1a
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:30
A3
Gewicht
Name
Name
Fundament
0905-00-00
4649.7 Maßstab
Mattheis 07.03.17
Beton
Concrete
Füllmaterial
Filling
Erde
Ground
Legende
450400
850
A A
600
600
1355
665
1929
3310
600
600
A-A
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
retis 1a
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:30
A3
Gewicht
Name
Name
Fundament
0905-00-00
4649.7 Maßstab
Mattheis
07.03.17
Beton
Concrete
Füllmaterial
Filling
Erde
Ground
Legende
450400
850
A A
600
600
1355
665
1929
3310
600
600
A-A
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
retis 1a
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:30
A3
Gewicht
Name
Name
Fundament
0905-00-00
4649.7 Maßstab
Mattheis 07.03.17
Beton
Concrete
Füllmaterial
Filling
Erde
Ground
Legende
Play level
concrete foundation
1. Select the play equipment location in consideration of the required safety
area (see Diagram 4: 3150 mm x 6950 mm).
2. Carry out excavation work for foundation as shown in Diagram 2 and 3.
After excavation, compress the foundation oor.
Note: Cover the foundation holes with the safety cover required for the height
of fall indicated.The combination equipment is built in on the play level. Pay
attention to items marked „play level” of play equipment!
3. Set up the 5 main concrete foundations (600 x 600, height 400 mm) acc. to
the dimensions indicated in diagram 2 + 3 in the quality class C 20/25.
4. After a setting period of 10-14 days, depending on weather conditions and
foundation size - clean the surface of the foundations and start with the instal-
lation of the combination equipment.
5. Place the climbing wall as shown in the overview and in the Diagram 2a on
the main foundation and do a rough aligning.
Note: Do not screw the base plates onto the foundations yet!
Diagram 3: Foundation plan
Reinforcement plan:
Concrete foundation with reinforcement
Main foundation: BSt 500S
Ever 4 stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class C 20/25

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved State: 24.03.2017 p. 3
Mounting instruction climbing net „retis 1“
Item-No. 515515402
6. Arrange the sliding bars and plug it with the delivered connection pipes at the
ladder bow. Screw it with cheese head screws M8 x 25 from below.
7. Adjust the climbing equipment at the foundations.
8. Drill holes into all foundations and screw the play equipment into the founda-
tions with the included heavy-duty dowels.
9. Seal the foundation with the safety cover required for the height of fall
indicated.
Critical drop height: 1700 mm.
Recommended surface material: sand, wood chip, gravel,
synth. fall protection.
10. After 3 months, check the screws at the joints and retighten them if
necessary.
11. Do not allow children to use the equipment before the installation has been
nished.
Attention: If the play equipment has been incompletely installed or partly dis-
mantled when carrying out maintenance and repair work, this may lead to
particular risks of injury for the user. For this reason, make clearly visible that the
equipment shall not be used in such cases.
NOTE: Play equipment, which contain components made of stainless steel
should not come with „normal“ steel parts in contact. Those steel parts may rub
off and leave small steel particles in combination with moisture brown rust stains.
If such corrosion occur on stainless steel parts, they are ne to remove with an
abrasive (240 grit).
Please take care when transporting and setting up the fact that the components
are made of stainless steel with no „normal“ steel parts in contact.
Diagram 4: Draufsicht mit Angabe des Sicherheitsfreiraums
3150
6950
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
retis 1a
6950x3150
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:20
A3
Gewicht
Name
Name
Draufsicht
0905-00-00
123.4 Maßstab
Mattheis
07.03.17

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved State: 24.03.2017 p. 4
Mounting instruction climbing net „retis 1“
Item-No. 515515402
In order to preserve a good visual appearance of your stilum playground equip-
ment over a long period one should take care of maintenance of the stainless
surface even despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall, should be frequently
cleaned from dirt and deposits due to air pollution and dirt caused by the atmos-
phere. Light soiling can easily be removed by using a high pressure cleaner. For
persistent deposits use a clean cloth moistened with a special liquid cleaner (e.g.
on phosphoric acid) and rinse off with clear water after a short application time.
During cleaning with mild abrasive components, only wipe over stainless steel
surface in polishing direction. For heavily soiled surfaces, polishes can be used
(e.g. for cleaning chrome on cars) or for greasy and oily dirt alcoholic cleaning
agents and solvents (e.g. ethyl alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the
surface again. Do not use any chloride or hydrochloric containing cleaning
products nor scouring powder, bleaching - or silver polish cleaner. Cleaning
intervals depend on type and degree of soiling as well as on demands made on
optical characteristics. Therefore cleaning is advisable at intervals of six to twelve
months – whereby in
the case of strong soiling it is appropriate to clean the playground equipment at
intervals of 3 to 6 months.