stilum Octo User manual

© stilum GmbH, Gewerbegebiet Larsheck, D-56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 08.06.2020 p. 1
Mounting instructions for balance „octo“
Item No. 51 5551 402
Diagram 1: Overall view of the play equipment

© stilum GmbH, Gewerbegebiet Larsheck, D-56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 08.06.2020 p. 2
Mounting instructions for balance „octo“
Item No. 51 5551 402
Diagram 2: Foundation plan
Reinforcement plan: Concrete foundation with reinforcement
Main foundation: BSt 500S
Stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class C 20/25 - C 25/30
4500
300
4340
450 410
450
4500
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
1
octo
Benennung
Gepr.
Blatt
Datum
Projekt
Gez.
Zeichnungsnummer
1:25
A3
Name
Name
Fundamentplan
0310-00-00
Maßstab
Schramm 22.05.18
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Beton
concrete
gewachsenes Erdreich
natural ground
Legende
stoßdämpfender Boden
shock-absorbing floor
Datum Änderung Rev
beliebiger Boden
optional floor
Play level
1. Select the location of the play equipment taking into account the required
minimum space (see diagram 3).
2. Carry out excavation work for the foundation as shown in diagram 2. After
excavation compress the foundation oor.
Note: The equipment is is installed at play level.
Pay attention to items marked „play level“ at play equipment!
3. Set up the concrete foundations according to diagram 2 with central, horizon-
tal reinforcement.
4. After a setting period of 10 – 14 days, depending on weather conditions and
foundation size, ll up and compress the holes between the foundation and
the foundation hole with excavation.
5. Clean the foundation surface and place the two parts of the balance equip-
ment on it. Screw it onto the foundation using the included heavy-duty
dowels.

© stilum GmbH, Gewerbegebiet Larsheck, D-56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 08.06.2020 p. 3
Mounting instructions for balance „octo“
Item No. 51 5551 402
6. Cover the entire impact area with fall protection according to the required drop
height in accordance with EN 1176-1.
Critical drop height: 410 mm
Recommended surface material: optional
Note: The ground must be smooth and free of edges.
With a smaller installation depth (special edition) we recommend synthetic fall
protection. In this case, make sure that protruding parts (e.g. screws, gusset
plates) are covered with appropriate fall protection.
7. Do not allow children to use the equipment before the installation has been
nished.
Attention: If the play equipment has been incompletely installed or partly dis-
mantled when carrying out maintenance and repair work, this may lead to particu-
lar risks of injury for the user. For this reason, make clearly visible that the equip-
ment shall not be used in such cases.
NOTE: Play equipment, which contain components made of stainless steel should
not come with „normal“ steel parts in contact. Those steel parts may rub o󰀨 and
leave small steel particles in combination with moisture brown rust stains.If such
corrosion occur on stainless steel parts, they are ne with an abrasive (240 grit) to
remove.
Please take care when transporting and setting up the fact that the components
are made of stainless steel with no „normal“ steel parts in contact.
Area of the minimum space
Diagram 3: Top view
1510
1510
3300
1500
7350
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
octo
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:30
A3
Gewicht
Name
Name
Draufsicht
0310-00-00
743.8 Maßstab
Schramm 22.05.18
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland