stilum Tendo User manual

© stilum GmbH, Gewerbegebiet Larsheck, D- 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
Mounting instructions for hanging rings „tendo“
Item-No. 55 1519 401
State: 22.01.2021 p. 1
health
Diagram 1: Overall view of the play equipment

© stilum GmbH, Gewerbegebiet Larsheck, D- 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
Mounting instructions for hanging rings „tendo“
Item-No. 55 1519 401
State: 22.01.2021 p. 2
health
1. Select the location of the play equipment taking into account the required
minimum space (see diagram 3).
2. Carry out excavation work for the foundations as shown in diagram 2. After
excavation compress the foundation oor.
Note: Pay attention to items marked „ground level“ at the equipment!
3. Set up the concrete foundations according to diagram 2 with central, horizon-
tal reinforcement.
4. After a setting period of 10 – 14 days, depending on weather conditions and
foundation size, ll up and compress the holes between the foundation and
the foundation hole with excavation.
5. Clean the foundation surface. Set up the both tubular frames and secure
them against falling over. Insert both hanging piepes into the frames and x
them with the supplied screws.
6. Align the equipment and screw the base plates to the foundation using the
included heavy-duty dowels.
Reinforcement plan: Concrete foundation with reinforcement
Foundation: BSt 500S
Stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class C20/25
Diagram 2: Foundation plan
400 450
3778
2520
A A
1100
500 1610 500
A-A
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
1
tendo
Benennung
Gepr.
Blatt
Datum
Projekt
Gez.
Zeichnungsnummer
1:25
A3
Name
Name
Fundamentplan
2128-00-00
Maßstab
Schramm 02.08.18
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Beton
concrete
gewachsenes Erdreich
natural ground
Legende
stoßdämpfender Boden
shock-absorbing floor
ES 11.01.21 stoßdämpfemder Boden A
DatumÄnderungRev
400 450
3778
2520
A A
1100
500 1610 500
A-A
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
1
tendo
Benennung
Gepr.
Blatt
Datum
Projekt
Gez.
Zeichnungsnummer
1:25
A3
Name
Name
Fundamentplan
2128-00-00
Maßstab
Schramm 02.08.18
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Beton
concrete
gewachsenes Erdreich
natural ground
Legende
stoßdämpfender Boden
shock-absorbing floor
ES 11.01.21 stoßdämpfemder Boden A
DatumÄnderungRev
ground level

© stilum GmbH, Gewerbegebiet Larsheck, D- 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
Mounting instructions for hanging rings „tendo“
Item-No. 55 1519 401
State: 22.01.2021 p. 3
health
7. Cover the entire impact area with fall protection according to the required
drop height in accordance with EN 1176-1.
Critical drop height: 1900 mm
Recommended surface material:
sand, wood chip, gravel, synth. impact protection.
With a smaller installation depth (special edition) we recommend synthetic
impact protection. In this case, make sure that protruding parts (e.g. screws,
gusset plates) are covered with appropriate fall protection.
8. Do not allow to use the equipment before the installation has been nished.
Attention: If the equipment has been incompletely installed or partly dis-
mantled when carrying out maintenance and repair work, this may lead to
particular risks of injury for the user. For this reason, make clearly visible that
the equipment shall not be used in such cases.
NOTE: Equipment, which contain components made of stainless steel should
not come with „normal“ steel parts in contact. Those steel parts may rub
o󰀨 and leave small steel particles in combination with moisture brown rust
stains.If such corrosion occur on stainless steel parts, they are ne with an
abrasive (240 grit) to remove.
Please take care when transporting and setting up the fact that the compo-
nents are made of stainless steel with no „normal“ steel parts in contact.
Diagram 3: Top view
6500
4400
1820
1836
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
tendo
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:50
A3
Gewicht
Name
Name
Draufsicht
2128-00-00
Maßstab
Schramm 02.08.18
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Area of the
minimum space

© stilum GmbH, Gewerbegebiet Larsheck, D- 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
Mounting instructions for hanging rings „tendo“
Item-No. 55 1519 401
State: 22.01.2021 p. 4
health
In order to preserve a good visual appearance of your stilum-equipment over a
long period one should take care of maintenance of the stainless surface even
despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently clea-
ned from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse o󰀨 with clear water after a short application
time. During cleaning with mild abrasive components, only wipe over stainless
steel surface in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on
cars) or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl
alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the sur-
face again.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type
and degree of soiling as well as on demands made on optical characteristics.
Therefore cleaning is advisable at intervals of six to twelve months – whereby in
the case of strong soiling it is appropriate to clean the equipment at intervals of
three to six months.