Stoneridge Orlaco MirrorEye MP User guide

MirrorEye MP
System manual
No. SM0974205 A 09
Set MirrorEye MP;
Art. No. 0415005
Set MirrorEye MP RHD + S;
Art. No. 0415015
Set MirrorEye MP LHD + S;
Art. No. 0415025
05/2019
English

2SM0974205 A 09
System manual
Preface
Before you start installing this equipment, please read this manual
carefully and follow all instructions. This system manual
describes the functions of the equipment, outlines the
connection options and explains how to put the equipment into
operation. We recommend that you keep this manual in a safe
place for reference purposes.
If you have any questions or issues concerning the operation
of this equipment, consult the relevant section in the manual or
contact Stoneridge/Orlaco.
All data is subject to change without notice. All dimensions are for
commercial use only. Camera/monitor systems from Stoneridge/
Orlaco comply with the latest CE, ADR, EMC, and mirror
regulations, where applicable. All products are manufactured in
accordance with an ISO 9001 quality management system, an IATF
16949 automotive quality management system, and an ISO 14001
environmental management systems, where applicable.
Safety
In order to guarantee safe operation, these safety
instructions must be read before you start using this
equipment.
• Do not open the enclosure. This can cause damage, short-
circuiting or electrical shocks.
• Do not expose the equipment to extreme temperatures.
This can cause deformation of the enclosure or damage to
internal components.
• Repairs may only be undertaken by Stoneridge/Orlaco.
• The equipment must be assembled as shown in this manual.
• If there have been alterations or changes to this equipment that
have not been specifically approved by Stoneridge/Orlaco, use
of this equipment is not permitted.
• The use of this system while driving is only permitted by
persons who are (legaly) authorized to operate the vehicle and
are considerd fysical capable of driving a vehicle.
• Note that regulations must be obliged on all times.
• Check proper functioning of the system before driving.
MirrorEye MP
Manual No. SM0974205, A 09
Set MirrorEye MP; Art. No. 0415005
Set MirrorEye MP RHD + S; Art. No. 0415015
Set MirrorEye MP LHD + S; Art. No. 0415025
MirrorEye set, Art. No. 0415005
MirrorEye set, Art. No. 0415015
MirrorEye set, Art. No. 0415025
Also refer to the following documents
Data sheet DS0965012
DS0965013
DS0965014
User Manual UM0972205
User Manual UM0972206

3
SM0974205 A 09
System manual
Checking Field of view
Remark
Before driving it’s mandatory
for the operator of the vehicle
to check if the legally prescribed eld of
view is displayed on the monitor.
Display of the system
Warnings
The system is designed to meet legal requi-
rements and to provide the most accurate
representation of a situation. However, the
operator must be aware that due to system
properties a situation might be represented
differently than expected.
The operator remains at all times responsi-
ble for the safe operation of the vehicle and
the assessment of situations during driving
and manoeuvering.
When the system shows a completely white
screen please powercycle the system to
restore it in working order.
1. UNECE R46 regulation
Uniform provisions concerning the approval of devices for indirect vision and of motor vehicles with regard to the
installation of these devices.
The MirrorEye system is developed as a mirror replacement as mentioned in UNECE R46 regulation. In order to use the
MirrorEye system as a mirror replacement the installation needs to be approved by the authorized body.
Warning:
Without installation- or type approval it’s prohibited
to use the MirrorEye system without mirrors
mounted on the vehicle.
Remark:
When mirrors are replaced by the MirrorEye system;
installation approval according to R46 is required.
For legal requirements see:
https://www.unece.org/fileadmin/DAM/trans/main/wp29/wp29regs/2018/R046r6am4e.pdf
The positioning and placement of the cameras and monitors is essential for a proper use of the system.
Without a correct installation the installation approval is not possible.
Contents Page
1. UNECE R46 regulation 3
2. Introduction 4
2.1. Surveillance camera 4
3. System descriptions 5
3.1. System view Set MirrorEye MP 5
3.2. System view Set MirrorEye MP RHD + S 6
3.3. System view Set MirrorEye MP LHD + S 7
3.4. MirrorEye set Layout 8
3.5. Camera and monitor mounting positions 8
3.6. MirrorEye installation 9
3.6.1. Distance lines 9
3.6.2. Maintenance instructions 9
4. Cabin Wire Harness electrical connections 10
5. Dimensions 11
6. Drilling template 12
7. Technical specifications 13
7.1. Set MirrorEye MP 13
7.2. Set MirrorEye MP RHD + S 14
7.3. Set MirrorEye MP LHD + S 15
8. Potential faillures 16
8.1. Monitor LED status indicator 17
9. MirrorEye settings menu 17
9.1. Menu 18
9.2. Status menus 19
10. Maintenance and cleaning 20
11. Disposal 20
12. General terms and conditions 20
13. Revision History 21

4SM0974205 A 09
System manual
2. Introduction
The MirrorEye system is a camera monitoring system, designed
to replace conventional class II and class IV rear-view mirrors on
vehicles. The MirrorEye MP system complies with the regulations
as described in R46R6.
System Description
The function of the MirrorEye system is to provide the operator
with the legally required class II, IV fields of view. See Figure 1.
Class II
In accordance with R46R6, a class II field of view for the main rear-
view device provides the operator rear vision along the length of
the vehicle towards the horizon.
Class IV
In accordance with R46R6, a class IV field of view for the wide-an-
gle view device provides the operator wide-angle rear vision along
the length of the vehicle.
2.1. Surveillance camera.
The suffix “+ S” denotes mechanical variants of the camera
housing that allow the use of a standalone surveillance camera.
This camera has to comply to the 2.5mm radius requirement of the
R46R6. This surveillance camera is not included in this certifica-
tion.
Driver
Ocular
Points
Driver
Ocular
Points
4m
Class IV
Class II
Class V
30m
1m
Ground level
Ground level
1m
15m
4,5m
25m
10m
1,5m
Ground level
Ground level
5m
2m
1
1,75m
3m
R=2m
4,5m
Larger Required View
Existing Class V Mirror View
Driver
Ocular
Points
Figure 1

5
SM0974205 A 09
System manual
3. System descriptions
Set MirrorEye MP, Art. No. 0415005
System overview
Camera MirrorEye MP Left side
Art. No. 0106045 Camera MirrorEye MP Right side
Art. No. 0106055
II II
IV IV
Class II camera
Class IV camera
IR Leds
Cabin Wire Harness
Art. No. 0391000
Open wire
Power input 24V/DC + CAN
Monitor 12,3”
Passenger side
Art. No. 0212505
Monitor 12,3”
Driver side
Art. No. 0212005
Not in use
Not in use
Class II camera
Class IV camera
IR Leds
3.1. System view Set MirrorEye MP, see figure 2.
The MirrorEye system set consists of:
- Two Camera units; each including two image sensors for class II/IV field of view, video processor, video channel
transceiver with bidirectional communication, heating and covers. All cameras are mounted outside the vehicle.
One camera on the left and one camera on the right.
- Two monitor units each with a 12.3-inch display for class II/IV image, video channel receiver with bidirectional
communication, monitor processor, diagnostics, CAN communication with vehicle, MirrorEye internal CAN
communication and housing. Mounted inside the Vehicle.
- Cabin Wire Harness. The cable cabin harness is the connection harness for the system to the vehicle with power
and ground wires. The harness has connectors on each side to connect the two monitors. Other connections are
the CAN communication wires and the connection to the service tool. See also figure 7, page 10.
Figure 2

6SM0974205 A 09
System manual
camera
Set MirrorEye MP RHD + S , Art. No. 0415015
System overview
Camera MirrorEye MP Left + S
Art. No. 0106065 Camera MirrorEye MP Right
Art. No. 0106055
II II
IV IV
Class II camera
Class IV camera
IR Leds
Cabin Wire Harness
Art. No. 0391000
Open wire
Power input 24V/DC + CAN
Monitor 12,3”
Passenger side
Art. No. 0212505
Monitor 12,3”
Driver side
Art. No. 0212005
Monitor 10”
Art. No. 0224000
Not in use
Not in use
Class II camera
Class IV camera
IR Leds
Power input
24V/DC Video
3.2. System view Set MirrorEye MP RHD + S, see figure 3.
The MirrorEye system set consists of:
- Two camera units; each having two image sensors for class II / IV field of view, in which the left-hand camera also has an
additional camera, video processor, video channel transceiver with bidirectional communication, heating and
covers. One camera unit mounted left outside on the Vehicle and one camera mounted right outside of the
Vehicle.
- Two Monitor units each with a 12.3-inch Monitor for class II/IV image, video channel receiver with bidirectional
communication, Monitor processor, diagnostics, CAN communication with vehicle, MirrorEye internal CAN
communication and housing. Mounted inside the Vehicle.
- The additional camera will be displayed on a separate monitor.
- Cabin Wire Harness. The cable cabin harness is the connection harness for the system to the vehicle with power
and ground wires. The harness has connectors on each side to connect the two monitors. Other connections are
the CAN communication wires and the connection to the service tool. See also figure 7, page 10.
- Cable 2m UNI DigiCoax with molded M16 4p connectors + Coax.
Figure 3

7
SM0974205 A 09
System manual
camera
Set MirrorEye MP LHD + S , Art. No. 0415025
System overview
Camera MirrorEye MP Left
Art. No. 0106045 Camera MirrorEye MP Right + S
Art. No. 0106075
II II
IV IV
Class II camera
Class IV camera
IR Leds
Cabin Wire Harness
Art. No. 0391000
Open wire
Power input 24V/DC + CAN
Monitor 12,3”
Passenger side
Art. No. 0212505
Monitor 12,3”
Driver side
Art. No. 0212005
Not in use
Not in use
Class II camera
Class IV camera
IR Leds
Monitor 10”
Art. No. 0224000
Power input
24V/DC Video
3.3. System view Set MirrorEye MP LHD + S, see figure 4.
The MirrorEye system set consists of:
- Two camera units; each having two image sensors for class II / IV field of view, in which the right-hand camera also has
a additional camera, video processor, video channel transceiver with bidirectional communication, heating and
covers. One camera unit mounted left outside of the Vehicle and one camera mounted right outside of the
Vehicle.
- Two Monitor units each with a 12.3-inch Monitor for class II/IV image, video channel receiver with bidirectional
communication, Monitor processor, diagnostics, CAN communication with vehicle, MirrorEye internal CAN
communication and housing. Mounted inside the Vehicle.
- The additional camera will be displayed on a separate monitor.
- Cabin Wire Harness. The cable cabin harness is the connection harness for the system to the vehicle with power
and ground wires. The harness has connectors on each side to connect the two monitors. Other connections are
the CAN communication wires and the connection to the service tool. See also figure 7, page 10.
- Cable 2m UNI DigiCoax with molded M16 4p connectors + Coax.
Figure 4

8SM0974205 A 09
System manual
1
2
3
4
1
2
3
4
1
2
Ocular Reference Point
45
30 Ocular Reference Point
A Pillar
A Pillar
A Pillar
Dimensions in mm
Ocular Reference Point
Center camera class IV lens
Center lens,
class IV
Center lens,
class IV
Center lens
Center lens
2550
Seat rails 745
745
Seat rails
490
550
490
3.4. MirrorEye set Layout, See Figure 5
1. Camera MirrorEye Left Side;
2. 12.3” Monitor unit, Driver Side;
3. Camera MirrorEye Right Side;
4. 12.3” Monitor unit, Passenger Side;
3.5. Camera and monitor mounting positions
The camera position must be as far to the front of the
Vehicle as possible to ensure that the class IV image can
be captured, see also figure 1, page 4. For drilling template
camera bracket see page 12.
The monitor position can be determined according to the
table below and the dimensions according to figure 5.
Installation requirement
Class Location Monitor Design viewing Design viewing Distance ORP
angle horizontal angle vertical to monitor
Class II driver 12,3” 0° -11° 0,815m
Class IV driver 12,3” 0° 11° 0,80m
Class II passenger 12,3” 0° -6° 1,225m
Class IV passenger 12,3” 0° 6° 1,22m
Figure 5

9
SM0974205 A 09
System manual
3.6. MirrorEye installation
3.6.1. Distance lines.
The distance lines are not visible by default but can be pro-
grammed and set according to rules, see instruction manual
UM0972206. This setting can only be done by your dealer. Dis-
tance lines can be progammed on both the driver-side monitor and
the passenger-side monitor. See Figure 6.
These distance lines are designed to be able to determine the
distance from other traffic on the road and to help the operator
change lanes safely.
There are 3 programmable distance lines (A, B and C).
The settings remain stored after power down. It is the responsibil-
ity of the dealer to make sure that they have a process in place to
make sure that the distance lines are calibrated properly accord-
ing to the description above and that this process is repeatable.
Stoneridge-Orlaco is not responsible for any errors in the calibra-
tion of the distance lines.
The distance lines must be assessed during vehicle installation
approval.
3.6.2. Maintenance instructions
Stoneridge-Orlaco advises the operator and/or owner of the vehicle
to regularly check the calibration of the distance lines. Besides this
Stoneridge-Orlaco strongly advises to check the calibration when
the vehicle is at a service station for servicing
Advise:
We strongly advise to contact your Stoneridge-Orlaco dealer for
detailed instructions regarding the installation. Figure 6
Driver
Ocular
Points
Distance lines
ABC
Monitor with
distance lines
displayed
A
B
C

10 SM0974205 A 09
System manual
Front side 9p
Female connector
To MirrorEye
Driver side
Camera +
Monitor Class II, IV
Front side 9p
Female connector
To MirrorEye
Passenger side
Camera +
Monitor Class II, IV
4
1
3
2
Front side
4p Deutsch DT
Female connector
Not in use
456
123
1 = Power (KL30)
2 = GND
4 = Ignition (KL15)
3 = CAN H (J Stick)
6 = CAN L (J Stick)
Power (KL30)
CAN 1H
CAN 1L
GND
Ignition (KL15)
CAN 3H
CAN 3L
Open Wire
To vehicle power + CAN
1 = Power (KL30)
2 = GND
3 = CAN H (J Stick)
4 = CAN L (J Stick)
3 = Power (KL30)
1 = CAN 1H
2 = CAN 1L
4 = CAN H (J Stick)
5 = CAN L (J Stick)
7 = CAN 3H
8 = CAN 3L
6 = GND
9 = Power (KL15)
3 = Power (KL30)
1 = CAN 1H
2 = CAN 1L
4 = CAN H (J Stick)
5 = CAN L (J Stick)
7 = CAN 3H
8 = CAN 3L
6 = GND
9 = Power (KL15)
Cabin Wire Harness ME 2.4m; Art. No. 0391000
456
123
1 = Power (KL30)
2 = GND
4 = Ignition (KL15)
3 = CAN H (J Stick)
6 = CAN L (J Stick)
Front side 6p
male connector
Not in use
Front side 6p
male connector
Not in use
3
1
7
93
1
7
9
Figure 7
The MirrorEye MP Set must be connected by
trained electricians. Under no circumstances
should you make connections that are not
described in this manual.
4. Cabin Wire Harness electrical connections

11
SM0974205 A 09
System manual
Figure 8
5. Dimensions
Units in mm
Units in mm
Bracket Drilling template MirrorEye MP Left, SCALE 1:1
149,5
341,5
30,2
45,2
70,5
37,4
Mounting holes for bracket
3x M5
Monitor 12,3” MirrorEye
Monitor active part
Class II
190 x 110mm
Class IV
95 x 110mm
332
Camera MirrorEye MP Left side/Right side
5p Molded male
Connector
114
62
20
27
∅9 Mounting holes
for bolts M8
Units in mm
Units in mm
Units in mm
Bracket Drilling template MirrorEye MP Left, SCALE 1:1
Monitor 10” HLED 1
332
Camera MirrorEye MP Left side/Right side
5p Molded male
Connector
114
62
20
27
∅9 Mounting holes for bolts M8
251
37,5
13,5
173
100
100
30
35,2
M5 (8x)
40
Surveillance
monitor
149,5
341,5
30,2
45,2
70,5
37,4
Mounting holes for bracket
3x M5
Monitor 12,3” MirrorEye
Monitor active part
Class II
190 x 110mm
Class IV
95 x 110mm
106

12 SM0974205 A 09
System manual
Figure 9
6. Drilling template
Units in mm
Units in mm
Bracket Drilling template MirrorEye MP Left, SCALE 1:1
149,5
341,5
30,2
45,2
70,5
37,4
Mounting holes for bracket
3x M5
Monitor 12,3” MirrorEye
Monitor active part
Class II
190 x 110mm
Class IV
95 x 110mm
332
Camera MirrorEye MP Left side/Right side
5p Molded male
Connector
114
62
20
27
∅9 Mounting holes
for bolts M8

13
SM0974205 A 09
System manual
Camera Units
Camera MirrorEye MP Left Camera Mirror Eye MP Right
Article numbers 0106045 0106055
Camera module Two image sensors for Class II/IV view, 1.4MP.
Video stream Uncompressed over Coax cable (3Gbps).
Night Vision Active Day/Night filter + IR LED.
Ingress protection IP69K
Optic Class II H/V: 17,8/37,6 deg. Class IV H/V: 56,5/61,5 deg.
Weight 1,66Kg/part. (Incl. cable)
Monitor 12,3” MirrorEye
Monitor driver side Monitor passenger side
Article numbers 0212005 0212505
Backlight TFT LED
Luminance Min 800cd/m2
Display module 12,3” (diagonal size), 720 x 1223 pixels for Class II image, 720 x 617 pixels for IV image.
Bracket Universal fastening for easy assembly to most vehicles.
Ingress protection IP54
Communication cam.-mon. High speed bi-directional over Coax cable, operational with active video channel.
Aspect ratio Portrait 3 : 8.
Frame rate 60 fps.
Weight 1,92Kg/part. (Incl. cable)
Cable Cabin Harness ME 2.4m
Article number 0391000
Electrical connections The cable cabin harness is the connection harness for the system to the vehicle with power and ground wires.
The harness has connectors on each side to connect the two monitors. Other connections are the CAN
communication wires and the connection to the service tool.
Lenght 2.4m
General
Mechanical tested and suitable for automotive applications.
Operating temperature -40°C - +85°C, (max +40°C with IR illumination).
Power supply 24V.
Power consumption Max 96W, 4A@24V. We advise to use a fuse of 10A.
Documentation User Manual UM0972205, UM0972206 and System Manual SM0974205.
Product identication C-03:M-02:O-02:S-04:V-02.
Compliance R46R6
R10R5
ISO-16750:2006-2012
ergonomic requirements
RoHS
Vibration resistance camera unit: 3G
7. Technical specications
7.1. Technical specications Art. No. 0415005; Set MirrorEye MP

14 SM0974205 A 09
System manual
Camera Units
Camera MirrorEye MP Left + S Camera Mirror Eye MP Right
Article numbers 0106065 0106055
Camera module Two image sensors for Class II/IV view, 1.4MP. Two image sensors for Class II/IV view, 1.4MP.
Additional camera.
Video stream Uncompressed over Coax cable (3Gbps). Uncompressed over Coax cable (3Gbps).
Night Vision Active Day/Night filter + IR LED. Active Day/Night filter + IR LED.
Ingress protection IP69K IP69K
Optic
Class II H/V: 17,8/37,6 deg. Class IV H/V: 56,5/61,5 deg. Class II H/V: 17,8/37,6 deg. Class IV H/V: 56,5/61,5 deg.
Class S H/V: 120/74 deg.
Weight 1,86Kg/part. (Incl. cable) 1,66Kg/part. (Incl. cable)
Monitor 12,3” MirrorEye
Monitor driver side Monitor passenger side
Article numbers 0212005 0212505
Backlight TFT LED
Luminance Min 800cd/m2
Display module 12,3” (diagonal size), 720 x 1223 pixels for Class II image, 720 x 617 pixels for IV image.
Bracket Universal fastening for easy assembly to most vehicles.
Ingress protection IP54
Communication cam.-mon. High speed bi-directional over Coax cable, operational with active video channel.
Aspect ratio Portrait 3 : 8.
Frame rate 60 fps.
Weight 1,92Kg/part. (Incl. cable)
Monitor 10” HLED 1
Monitor for additional camera
Article number 0224000
Specications See DS0962201
Cable Cabin Harness ME 2.4m
Article number 0391000
Electrical connections The cable cabin harness is the connection harness for the system to the vehicle with power and ground wires.
The harness has connectors on each side to connect the two monitors. Other connections are the CAN
communication wires and the connection to the service tool.
Lenght 2.4m
Cable 2m UNI Digicoax
Article number 0311010
Specications See DS0960131
General
Mechanical tested and suitable for automotive applications.
Operating temperature -40°C - +85°C, (max +40°C with IR illumination).
Power supply 24V.
Power consumption Max 96W, 4A@24V. We advise to use a fuse of 10A.
Documentation User Manuals UM0972205, UM0972206 and System Manual SM0974205.
Product identication C-03:M-02:O-02:S-04:V-03.
7.2. Technical specications, Art. No. 0415015; Set MirrorEye MP RHD + S
Compliance R46R6
R10R5
ISO-16750:2006-2012
ergonomic requirements
RoHS
Vibration resistance camera unit: 3G

15
SM0974205 A 09
System manual
Camera Units
Camera MirrorEye MP Left Camera Mirror Eye MP Right + S
Article numbers 0
106045 0106075
Camera module
Two image sensors for Class II/IV view, 1.4MP. Two image sensors for Class II/IV view, 1.4MP.
Additional camera
Video stream
Uncompressed over Coax cable (3Gbps). Uncompressed over Coax cable (3Gbps).
Night Vision
Active Day/Night filter + IR LED. Active Day/Night filter + IR LED.
Ingress protection
IP69K IP69K
Optic Class II H/V: 17,8/37,6 deg. Class IV H/V: 56,5/61,5 deg. Class II H/V: 17,8/37,6 deg. Class IV H/V: 56,5/61,5 deg.
Class S H/V: 120/74 deg.
Weight
1,66Kg/part. (Incl. cable) 1,86Kg/part. (Incl. cable)
Monitor 12,3” MirrorEye
Monitor driver side Monitor passenger side
Article numbers 0212005 0212505
Backlight
TFT LED
Luminance
Min 800cd/m2
Display module
12,3” (diagonal size), 720 x 1223 pixels for Class II image, 720 x 617 pixels for IV image.
Bracket
Universal fastening for easy assembly to most vehicles.
Ingress protection
IP54
Communication
cam.-mon. High speed bi-directional over Coax cable, operational with active video channel.
Aspect ratio
Portrait 3 : 8.
Frame rate
60 fps.
Weight
1,92Kg/part. (Incl. cable)
Monitor 10” HLED 1
Monitor for additional camera
Article number 0224000
Specications
See DS0962201
Cable Cabin Harness ME 2.4m
Article number 0391000
Electrical connections
The cable cabin harness is the connection harness for the system to the vehicle with power and ground wires.
The harness has connectors on each side to connect the two monitors. Other connections are the CAN
communication wires and the connection to the service tool.
Lenght
2.4m
Cable 2m UNI Digicoax
Article number 0311010
Specications
See DS0960131
General
Mechanical tested and suitable for automotive applications.
Operating temperature
-40°C - +85°C, (max +40°C with IR illumination).
Power supply
24V.
Power consumption
Max 96W, 4A@24V. We advise to use a fuse of 10A.
Documentation
User Manuals UM0972205, UM0972206 and System Manual SM0974205.
Product identication C-03:M-02:O-02:S-04:V-04.
7.3. Technical specications, Art. No. 0415025; Set MirrorEye MP LHD + S
Compliance R46R6
R10R5
ISO-16750:2006-2012
ergonomic requirements
RoHS
Vibration resistance camera unit: 3G

16 SM0974205 A 09
System manual
Symptom Action driver
1. Black screen 1. Driver should stop the vehicle in a safe manner,
as soon as possible.
2. Blue screen 2. Driver should stop the vehicle in a safe manner,
as soon as possible.
3. Overlay menu not available 3. Driver should assess the problem and stop
vehicle if necessary.
4. Test pattern shown (image see page 14) 4. Driver should stop the vehicle in a safe manner,
as soon as possible.
5. Mirrored image 5. Driver should stop the vehicle in a safe manner,
as soon as possible.
6. Flipped image 6. Driver should stop the vehicle in a safe manner,
as soon as possible.
7. Full in screen deformation of image 7. Driver should stop the vehicle in a safe manner,
as soon as possible.
8. Partly in screen deformation of image 8. Driver should assess the problem and stop
vehicle if necessary.
9. Color representation of image wrong 9. Driver should assess the problem and stop
vehicle if necessary.
10. Incorrect image cropping and scaling 10. Driver should assess the problem and stop
vehicle if necessary.
11. Incorrect image sharpness 11. Driver should assess the problem and stop
vehicle if necessary.
12. Corrupted image stream due to Electric 12. Driver should assess the problem and stop
Magnetic Interference (EMI) vehicle if necessary
13. Wrong placement of camera views on monitor 13. Driver should assess the problem and stop
vehicle if necessary.
14. Image too bright 14. Driver should assess the problem and stop
vehicle if necessary.
15. Image too dark 15. Driver should assess the problem and stop
vehicle if necessary.
If the above mentioned failures occur,
the operator must stop the vehicle
and must not resume driving until the
failures are resolved.
8. Potential failures:
In the event of MirrorEye
system failure, please
contact your dealer.

17
SM0974205 A 09
System manual
Figure 10
Sensor
LED indicator
8.1. Monitor LED status indicator
The 12,3” monitor has a red LED status indicator. See
Figure 10. This LED will be activated in the following
situations:
• MirrorEye Monitor in reset.
• MirrorEye video stream failure.
• MirrorEye Monitor TFT panel failure.
• MirrorEye Monitor boot failure.
9. MirrorEye Settings menu
The Menu of the MirrorEye system can only be accessed via a vehicle
controller and by a dealer. In this menu, the distance lines can be
programmed as well as other features of the MirrorEye system.
See manual UM0972206.
Functions of the buttons:
Button 1: Day/night both sides
Button 2: Not applicable
Button 3: Manual monitor brightness adjustment
Button 4: Driver side, Menu (long push)
Button 5: Passenger side, Menu (long push)
Press on turning knob: Enter, changes are stored
N.B. Panning is not supported.
Other available info in the menu is described in the next chapter.
1
4
3
5
2
Knob

18 SM0974205 A 09
System manual
Driver side
Passenger side
Settings
Panning
Night vision
Monitor
Distance lines
Status*
Exit
Driver menu
Panning
Status*
Exit
Night vision menu
IR light intensity (%)
Status menu
MirrorEye camera
MirrorEye monitor
Camera modules
Vehicle
Panning
System monitor
System dump
Distance lines dump
Monitor menu
Auto brightness
Day brightness
Night brightness
Distance lines menu
Enable distance lines
Panning menu
Enable automatic panning
Calibrate steering sensor
Trailer wheelbase (mm)
Trailer lenght (mm)
Trailer width (mm)
Default manual panning angle
Panning menu
Default manual panning angle
Status menu
MirrorEye camera
MirrorEye monitor
Camera modules
Vehicle
Panning
System monitor
System dump
Distance lines dump
*Status menu: Shows system information that
can be requested in case of a service call.
More details see Chapter 9.2. next page.
9.1. Menu

19
SM0974205 A 09
System manual
9.2. Status menus
Example of system information
MirrorEye camera
Example of system information
MirrorEye monitor
Example of system information
Camera modules
Example of system information
Vehicle
Example of system information
System monitor
Example of system information
System dump

20 SM0974205 A 09
System manual
10. Maintenance and cleaning
Passive cleaning ensures that the camera lenses stay clean, using a
coating on the glass.
Automatic heating ensures that the camera lenses stay clear of ice
and fog by evaporating water from the front of the camera lenses.
Use a high-quality, safe detergent and a soft cloth to remove dirt
and debris from the lenses.
Do not clean this product using aggressive chemicals
or abrasive cleaning agents.
11. Disposal
Disassembly, removal and disposal. Local regulations for dealing
with waste must be followed when disposing of disassembled
components or entire units.
12. General terms and conditions
Stoneridge/Orlaco Products BV is not liable for damage resulting
from inadequate servicing, incorrect usage or alterations made to
the equipment without informing the manufacturer in writing.
This installation manual has been made available by
Stoneridge/Orlaco.
All rights reserved. No part of this manual may be reproduced
and/or made public in printed form, in photocopy form or on
microfilm, or in any other way, without the prior written permission
of Stoneridge/Orlaco. This also applies to the associated drawings
and figures.
Stoneridge/Orlaco reserves the right to make changes to com-
ponents at any time without informing customers beforehand or
directly. All dimensions given are for commercial purposes.
For information regarding repairs that is not covered in this
manual, please contact the Stoneridge/Orlaco Products BV service
department.
This manual has been prepared with all due care and attention.
However, Stoneridge/Orlaco cannot be held responsible for any
errors in this manual or any consequences thereof.