StorageTek FLEXLINE 96126 User manual

PART NUMBER EDITION NUMBER
PRODUCT TYPE
SOLUTIONS
FLEXLINE
ONLINE STORAGE SYSTEMS
INSTALLATION INSTRUCTIONS FOR SOLARIS
Open Systems Host Attach
96126 2
TM

FlexLine™
200/300 Series
Installation Instructions
for SOLARIS open
systems disk host attach

ii Second Edition 96126
StorageTek Proprietary
Information in this file is subject to change. In the event of changes, the information
will be revised. Comments concerning its contents should be directed to:
200/300 Series Program Manager
Storage Technology Corporation
One StorageTek Drive
Louisville, CO 80028-2129
or sent email to: [e-mail]
Export Destination Control Statement
These commodities, technology or software were exported from the United States in
accordance with the Export Administration Regulations. Diversion contrary to U.S. law is
prohibited.
Proprietary Information Statement
This document and its contents are proprietary to Storage Technology Corporation and may
be used only under the terms of the product license or nondisclosure agreement. The
information in this document, including any associated software program, may not be
reproduced, disclosed or distributed in any manner without the written consent of Storage
Technology Corporation.
Copyright Statement
© 2004 Storage Technology Corporation. All rights reserved. StorageTek and the StorageTek
logo are trademarks or registered trademarks of Storage Technology Corporation. Other
products and names mentioned herein are for identification purposes only and may be
trademarks of their respective companies.
Information Control
The information in this document, including any associated software program, may not be
reproduced, disclosed or distributed in any manner without the written consent of Storage
Technology Corporation.
Should this publication be found, please return it to StorageTek, One StorageTek Drive,
Louisville, CO 80028-5214, USA. Postage is guaranteed.

96096 Second Edition iii
StorageTek Proprietary
Summary of Changes
The following is the history and summary of changes for this publication.
Date Edition Description
October 2003 First Initial Release
October 2004 Second Updated to reflect new FlexLIne™ terminology

Summary of Changes
iv Second Edition 96096
StorageTek Proprietary
This page intentionally left blank.

96126 Second Edition 1
StorageTek Proprietary
1
1
Solaris - Installation
Instructions
The following pages help ensure that you order and configure a viable solution
for your SUN operating environment running Solaris 2.7, 2.8, or 2.9 (and
appropriate patches - see Table 1 on page 5). Customers and StorageTek
personnel should also be familiar with the FlexLine™ 200/300 Series storage
system Site Preparation Guide, the Storage Manager Concepts Guide, and
the Storage System Planning Checklist.
■Introduction
This manual is organized to help plan your SUN Solaris configuration, provide
order information, and help to install and attach your storage system to the
SUN host server running Solaris. The following should be used in conjunction
with the Siebel configurator.
Plan your site configuration
Prior to placing an order for StorageTek storage equipment, one should make
sure of the system needs. First measure the locations of each current and
future host, storage system, and other network components. Fill in this form
with the requested information.
✔Parameter Outcome
Solaris operating system
Distance between host and storage
system
Distance between other devices
Number of HBAs needed (two are
recommended)
Number of storage systems being
installed
Number of FC cables needed

Solaris - Installation Instructions-
2 Second Edition 96126
StorageTek Proprietary
Select Host Adapter (s)
Pick the type and quantity of the fibre channel Host Bus Adapters (HBAs)
needed for your host systems. Refer to the Interop Tool for connectivity
information.
Select the Fibre Channel Cables
Select the length of fiber optic (or copper) cable and the quantity for
connection to the host systems. The following is an example of optical cables
that may be ordered through StorageTek to attach a QLA2300F HBA to the
Control Module (aka Controller). Write in the quantities needed.
There are also LC to SC cables that would allow one to use a 2 Gb HBA and
cables with existing switches. The following cables are available in this event.
Quantity 2 Gb FC Optical Cable Description Part #
10 meters (32.8 feet) LC to LC Duplex 10800221
50 meters (164 feet) LC to LC Duplex 10800222
100 meters (328 feet) LC to LC Duplex 10800223
Note: Other lengths are available. Consult the Siebel Configurator.

96126 Second Edition 3
StorageTek Proprietary
Introduction
If installing through a switch, you may need a set of the following.
Check your quantities against your earlier distance measurements to ensure
your order includes all cable attachments. Also, if ordering copper cables,
make sure that the connector ends meet your need. One end mates with the
HBA, and the other end, typically, mates with the control module’s host
interface minihubs (or array module host ports).
Note: Unless there is an existing management station, cable connections to
the management station should be via 10BaseT Ethernet.
Typically, LC to LC Duplex Fibre Channel short wave optical cables are used
with the HBAs and the controller’s host minihubs, which have Small Form
Factor Packaged (SFP) Transceivers.
Place your Order
Make sure that you have the following.
When you make a new order, a CD-ROM along with a CD insert, commonly
called a Quick Start Guide will be in your host attach kit. The Quick Start Guide
will walk you through your installation—first referring you to the
Preconfiguration and Maintenance Setup Instructions, P/N 95966, and then to
any special instructions written to support your particular operating system
installation.
Quantity FC Optical Cable Description Part #
10 meters (32.8 feet) LC to SC 10800231
50 meters (164 feet) LC to SC 10800232
100 meters (328 feet) LC to SC 10800233
Quantity 1 Gb FC Optical Cable Description Part #
10 meters (32.8 feet) SC to SC Duplex 10800134
50 meters (164 feet) SC to SC Duplex 10800137
100 meters (328 feet) SC to SC Duplex 10800138
Note: Other lengths are available. Consult the Siebel Configurator.
✔Description
SUN Server running Solaris 2.7, 8, or 9 (and appropriate patches)
HBA(s)
Fibre Channel cables to configure your subsystem

Solaris - Installation Instructions-
4 Second Edition 96126
StorageTek Proprietary
CD-ROM file structure
During your installation you will be asked to install files from the CD supplied in
your host-attach kit. The CD is structured (in most cases) with two main
folders (Docs and Software). Inside the Docs folder are subfolders with
pertinent documentation. The following table shows the subfolder names.
Inside the Software folder you will find files called: client, agent, runtime,
RDAC, and utilities.
Note: Some operating systems will have additional directories such as a
Host Adapter, MIBs, or a Drivers folder.
A special SMclient (Field Tool) CD is available and required to fulfill your
preconfiguration requirements. It has special software tasks and applications
that may be necessary to upgrade your storage system.
Note: Refer also to the PDF documents and configuration and support files
to assist with your installation, and use the Interop Tool to get the latest
connectivity information.
■Storage System and Storage Manager - Overview
FlexLine™ 200/300 Series storage systems provide access to high-end
storage using Fibre Channel and RAID technology.
This document was created to aid in installing a storage system into a Solaris
operating environment. It includes driver information, steps to take when
planning and assembling a SAN installation, and a list of frequently asked
questions (and problems) that may be encountered. This manual is intended
to provide tips on attaching or creating a SAN environment as well as giving
some examples of problems that have been encountered.
In addition to this manual, information is available on the CRC by going to
Current Products >> Disk or Current Products >> Software. The CRC also has
tech tips, FAQs, notices and bulletins, and software updates.
Note: Firmware and NVSRAM updates may be downloaded from the CRC.
Backup documentation is on the engineering web page at:
http://gandalf.stortek.com/ctp/index.html
Sales and Preinstall Diagnostic and Service Engineering Papers
Hardware Install Cabinet Docs Miscellaneous
Software Install Release Notes

96126 Second Edition 5
StorageTek Proprietary
Installation
■Installation
Once you have ordered your hardware and software, read the following
information on how to attach your storage system to a SUN Server running
Solaris 2.7, 8, or 9 (and appropriate patches).
Before You Begin
The materials needed for the installation are listed below. Check to see that
you have each of these items. The following pages provide more information
about these materials (see headings) with specific steps and details on what
to do.
Before you begin, make sure you have these items:
1. A SUN Server running Solaris 2.7, 8, or 9 (and appropriate patches)
2. One or more HBA(s)—appropriate to your storage system
3. SFP Transceivers for the Control Module/Array Module/Drive Module(s)
4. Fibre Channel cable(s) that will connect the host to the storage system
5. A storage system that is fully configured.
Note: If you don’t have your storage system configured, you can attach your
laptop running the latest SMclient Field Tool to it. This will enable you
to assign drives, LUNs, and volumes.
Table 1. Solaris Patches (minimum versions)
Refer to the SANtricity Storage Manager version 9.1 Installation Guide
for Solaris, which will have the latest patch levels required to run your
200/300 Series solution.
Preliminary Steps
Do the following prior to the installation.
Solaris 2.6 refer to manual 96096
Solaris 7 106541-11 Kernel jumbo patch
107078-18 OpenWindows patch
Solaris 8 06 jumbo patch
Solaris 9 112233-06
Notes:Two Terabyte support requires
patches 113998-05 and 113993-06

Solaris - Installation Instructions-
6 Second Edition 96126
StorageTek Proprietary
Check your operating system and patch revision levels
Use the following commands to assist you.
# uname -a
# showrev -p
Install the Storage System
Refer to the appropriate storage system Site Preparation Guide and hardware
installation documents, as needed. Do NOT, however, attach fibre channel
cables at this time.
After placing the hardware, refer to the Preconfiguration and Maintenance
Setup Instructions, P/N 95966, and the Storage Manager Concepts Guide.
This will enable you to understand the proper configuration for the business
environment, and to understand how to attach your laptop in order to configure
the storage system for communications with your management station.
Note: The management station is used to configure and/or verify that the
LUNs are set up as desired.
If you need more information about configuring LUNs, refer to the software
installation guide or use the GUI help function.
Install your storage manager GUI onto the customer’s storage management
station (attached via ethernet), and verify that the LUNs are set up as desired.
Proceed to the next section to verify or install the NVSRAM file to the storage
system.
Load NVSRAM
1. Verify or install the current NVSRAM (available on the CD in your host
attach kit) onto the control module (controller). Refer to the Storage
Manager Concepts Guide, which provides the command for the SMclient:
Storage Array >> Download >> NVSRAM
The following instructions tell how to attach the HBAs and other components
onto your Solaris host.
Before you perform these instructions, check to see that you:
• are running Solaris 2.7, 8, or 9 with the most current patches, as
required.
• have the appropriate installation kit (HBAs, cables, etc.)
• know the configuration for your customer’s site.

96126 Second Edition 7
StorageTek Proprietary
Installation
Install the Host Bus Adapters (HBAs)
The following steps explain how to install the host adapters.
1. Quit any applications that are running and halt (down) the operating
system.
Note: If your server supports, Hot Add PCI, refer to your hardware
manuals for specific instructions.
2. Power off the Solaris host, as appropriate.
3. Install the host bus adapter onto the host.
Note: There are various types of Solaris servers. Locate the
I/O card, which may be on a card module or behind an access
panel. See examples below.
4. Power up the host.
Install HBA Drivers
Install the driver according to the instructions that came with the HBA, and
modify the configuration file in the /kernel/drv directory, as appropriate.
Refer to the Interop Tool for the latest connectivity information. See page 2.
Install Storage Manager components
Refer to the SANtricity Storage Manager version 9.1 Installation Guide for
Solaris. The Storage Manager components are located on the CD that comes
with your host attach kit.
Note: Before you reboot (as mentioned at the end of the Installation Guide
procedures), install the Fibre Channel cables as instructed in the
following section.

Solaris - Installation Instructions-
8 Second Edition 96126
StorageTek Proprietary
Install Fibre Channel Cable
Attach cables using the following procedures.
1. Route the fibre channel interface cables between the storage system and
the host or per your customer’s system configuration plans.
2. Attach the fibre channel cables to the INPUT connectors on the
controller’s host interface minihubs (or array module host ports).
The following photograph shows the input side of a control module, showing
the 2 Gigabit LC to LC Fibre Channel (FC) shortwave (fiber-optic) cable.
Make sure that your minihub speed is set to correspond with your HBA and
switch speed. Also ensure that your host is attached to different controllers, as
shown below..
Photographs of the storage system host interface ports (on a control module’s
host minihubs and on an array module’s controller FRU) are shown below.
3. Connect the other end of the fibre cable(s) to the Host Bus Adapter (HBA).
See example below.
1234
Host Minihub 1 and 3 are
supported by Controller A Host Minihub 2 and 4 are supported by Controller B

96126 Second Edition 9
StorageTek Proprietary
Installation
Note: Refer to StorageTek’s Interop Tool for the latest connectivity
information. See page 2.
If necessary, refer to FlexLine’s hardware and software Installation Guides, or
to BladeStore’s Installation, Operation, and Maintenance Guide, P/N 96080 for
detailed installation information.
Refer to the Control Module/Array Module/Drive Module User’s Guides for
servicing information.
Note: The Hardware Cabling Guide provides cable routing information for
most FlexLine 200/300 Series storage system solutions. It help you
route the drive interface cables to the drive module ESMs.
Refer also to the F40 Cabinet User’s Guide, P/N 96100, and to the Installation
and Mounting Supplement, P/N 95972. These manuals can be found on the
CRC and on the engineering web page at:
http://gandalf.stortek.com/ctp/cabinet/
The following BladeStore configuration drawing should help you route drive
interface cables to blade modules (blade trays). This is the only storage
system not covered in the Hardware Cabling Guide. This information will help
you do an installation into a non-StorageTek cabinet.
Note: You should always make sure that there are two sets of redundant
loops (as shown in the following BladeStore example).
LC to LC Duplex
FC cables

Solaris - Installation Instructions-
10 Second Edition 96126
StorageTek Proprietary
Verify the install
1. After running the reconfiguration reboot, verify that you can see the
volumes by typing the format command.
A
< Controllers >
BSide
0Side
1
Blade Tray 5
(height=6U)
Blade Tray 4
(height=6U)
Blade Tray 3
(height=6U)
Blade Tray 2
(height=6U)
Blade Tray 1
(height=6U)
Blade Tray 0
(height=6U)
Control module
(height=4U)
B
A
Host-side
FC input
cables

NEED MORE INFORMATION?
www.storagetek.com
ABOUT STORAGETEK
Storage Technology Corporation (NYSE: STK)
is a $2 billion global company that enables
businesses, through its information lifecycle
management strategy, to align the cost of storage
with the value of information. The company’s
innovative storage solutions manage the
complexity and growth of information, lower
costs, improve efficiency and protect investments.
For more information, visit www.storagetek.com,
or call 1.800.275.4785 or 01.303.673.2800.
WORLD HEADQUARTERS
Storage Technology Corporation
One StorageTek Drive
Louisville, Colorado 80028 USA
1.800.525.0369
© 2004 Storage Technology Corporation, Louisville, CO.
All rights reserved. Printed in USA. StorageTek and the
StorageTek logo are registered trademarks of Storage
Technology Corporation. Other names mentioned may be
trademarks of Storage Technology Corporation or other
vendors/manufacturers.
StorageTek equipment is manufactured from new parts, or
new and used parts. In some cases, StorageTek equipment
may not be new and may have been previously installed.
Regardless, StorageTek's standard warranty terms apply,
unless the equipment is specifically identified by StorageTek
as “used” or “refurbished.”
Replacement parts provided under warranty or any
service offering may be either new or equivalent-to-new,
at StorageTek’s option. Specifications/features may change
without notice.