Storagewerkz Mywerkz 46000 User manual

Please read these instructions carefully before using.
Load capacity : 60 Lbs.
Thank you for purchasing a storagewerkz™ Garage Storage System.If you have any questions or require support during this time, please contact
our customer service department at [e-mail].
46000 – with a weight capacity up to 60 lbs.
Warning!
Before installing your new storagewerkz™ Garage Storage System, please read and fully understand the instructions and warnings contained in this
manual. Failure to follow these instructions completely can result in serious bodily injury, damage to the equipment or voiding of the warranty.The
installer is responsible for following these instructions to ensure that all components are installed correctly.
• Installations should be performed by someone with proper mechanical skills and experience in basic assembly.
• The surface where the unit is to be installed should be inspected to verify the weight of the equipment being installed can be supported.
• Not following these guidelines can result in damage to not only the mounting surface, but the unit and equipment as well. If necessary, reinforce
the mounting surface to properly accommodate the installed equipment.
• It is the responsibility of the installer to make sure the installed equipment does not exceed the maximum weight indicated for this unit.
• Always inspect the area behind the mounting surface. Make sure it is free of gas, water or waste lines and electrical cables and wires.
• Make sure to tighten all screws properly, but do not overtighten. Overtightening can greatly reduce the screw’s ability to securely support the unit
and the attached equipment.
Instruction Manual
MODEL: 46000

Supplied Parts :
Parts not shown to scale
Tools Required for Installation
• Phillips screwdriver
• Drill
• Stud finder
• 1/4” drill bit for concrete and cinder block walls
• 3/32” drill bit for wood stud walls
Parts List
• Rail (1)
• End caps (2)
• Concrete anchors (8)
• Screws (8)
• Hooks (4)
Wood Stud Mounting
Caution!
To ensure that this unit is properly attached to the mounting
surface, the wall frame must be mounted to two studs at least
16” apart.
1) Use a stud finder to locate a stud.
2) Making sure the rail is level, use it as a guide to mark the
mounting holes. You will need to mark at least 4
mounting holes.
3) Set the rail aside while drilling.
4) Pre-drill a 3/32” hole in each stud at the spot marked in the
last step.
5) Place the rail against the wall and line up the appropriate
holes with the pre-drilled holes.
6) Insert screws through the rail and into each of the
pre-drilled holes.
7) Carefully tighten each screw. Take care not to overtighten
any of the screws. Overtightening may result in damage to
the wall.
Clipping the hooks to the rail.
This kit includes four varying sized hooks designed to fit a wide
range of storage needs.
1) Place the top of the base of the hook over the top lip of the
rail in the desired location.
2) Press the bottom of the base of the hook into the rail until
you feel it “snap” into place.
3) To adjust the placement of the hook, lift the front of the hook
up. You will feel the hook “un-snap” from the rail. You may
then slide the hook to the desired location on the rail.
Concrete Mounting
Caution!
To ensure that the unit is properly attached to the mounting
surface, the supplied anchors must be used when installing in
concrete, brick or cinder block. DO NOT drill into the grout or
mortar between blocks.
1) Hold the rail securely against the wall, ensuring it is level.
2) Mark at least 6 holes to be drilled. These will be used for
securing the rail.
3) Set the rail aside while drilling.
4) Drill the holes using a 1/4” masonry drill bit.
5) Put a concrete anchor into each of the holes you just drilled.
6) Using a hammer, gently tap each anchor until both are
flush with the wall.
7) Hold the rail in the proper position against the wall.
8) Insert the screws through the rail and into each of the
pre-drilled holes.
9) Carefully tighten each screw. Take care not to overtighten
any of the screws. Overtightening may result in damage to
the wall.
Assembly Hardware:
Screws
8pcs
Plastic Anchor
8pcs