Storm RC X3UCAV User manual

Description of switch location and function
Transmitter battery
Transmitter and receiver bingding
Lower voltage warning & return to land function
GPS signal
Unlock process
Stabilize mode
Direction lock
Althold
Gps loiter
(RTL)
Why failsafe function
3

GPS
Motor
LED indicator for
APM controller system
working status
(Blue color)
Alarm light for battery
power status
(Red color)
Alarm light for
Low power
(Red color)
LED indicator for
APM controller system
working status
(Blue color)
Gimbal

SW1
Channel-7 Channel-8
SW2
Bind
Mode 1
Mode 2
D/R
SW1
Channel-7Channel-8
Throttle & Rudder Stick Elevator & Aileron Stick
SW2
Bind
Mode 1
Mode 2
D/R
Press the button and power on the transmitter for binding.
Press the button, then there are Bi Bi Bi…. sounds, it indicate the radio change to mode1mode.
Press the button, then there are Bi Bi Bi… sounds, it indicate the radio change to mode2 mode.
Power on the transmitter, then press the button, it indicate the travel value changed to 60%(slow flight) when the sound Bi.
and it indicate the travel value changed to 100%(fast flight) when the sounds Bi Bi.
Bind
Mode 1
Mode 2
D/R
Stabilize mode.0
Altitude hold.1
Direction lock. 2
Stabilize mode.0
Altitude hold.1
Direction lock. 2
0.Stabilize mode
1.GPS loiter
2.GPS RTL
0.Stabilize mode
1.GPS loiter
2.GPS RTL

Sw1 location Sw2 location
7、Description of switch location and function：
8、Transmitter battery:
0
1
2
0
1
2
SW1 SW2 Function
0
1
2
0
0
0
0
0
1
2
Stabilize mode
Altitude hold
Direction lock
GPS loiter
GPS RTL
Rolling
Tilting
CH7
CH7

4\Press the BIND switch, turn on the power switch, keep waiting for 10 seconds, and then release the BIND switch. It indicates
Binding success if the RED light on receiver is steady on .
9

10、Lower voltage warning & Auto landing function：
11、GPS signal
When outdoor flying under GPS mode, firstly searching the satellite, GPS hold & return to landing mode can work while satellite exceed 6pcs.
Blue LED light start flashing when satellite exceed 6pcs. If satellite below 6pcs, there is no light.
Red alarm light is flashing while battery voltage under 10.8V.
GPS signal
8
Lower voltage warning & AUTO Landing function: X3 controller box can automatically inspect the battery voltage. The Battery po
wer indicator is blinking red when battery voltage below 10.8V. X3 will automatically launch landing program when battery volta
ge under 10.5V. During the automatic landing, the transmitter still can control Aileron, Rudder,forward and backward.

12

0
1
2
0
1
2
SW1&SW2 set at "0" SW1&SW2 set at "0"
Solid blue LED light indicate successful unlocking. Flashing blue LED light indicate locking.
The propeller can not rotate when controller system is locking.
SW1&SW2 set at "0"
13
14
Pull the rudder switch and hit the right corner of bottom until the LED flashing in Blue to release.(shows as above picture)

0
1
2
0
1
2
Sw1set at " 2",sw2 set at "0".
Sw1set at " 1",sw2 set at "0" .
15
16

0
1
2
0
1
2
RTL
Sw1set at "0",sw2 set at " 1" .
Sw1set at "0",sw2 set at " 2" .
17
18
19

GPS signal
20
13
3

2.Move the Throttle & Rudder switch to the bottom right corner, after 12 seconds, quadcopter get into flight stabilized control calibration
mode when Blue LED change from solid blue to fast flashing. And then take off the quadcopter, keep hovering, the calibration is finished
when Blue LED stop fast flashing.
3

2.Compass get into calibration condition when blue LED is fast flashing.
E F

23
20123 brushless 920KV 20123 brushless 920KV R