Storm RC X5 Ucav User manual

Main rotors:1045*4
Flight weight: 685g
Motors: 2810 brushless motor *4
ESC: 30A brushless ESC
Receiver: 2.4Ghz,8 channel receiver
Transmitter: 2.4Ghz,8 channel and programmable. GPS MODULE
Battery: 3s,11.1V,2200mAh
1.Introduction 2
2.General safety precautions and warings 3
3.Charging the flight battery 3
4.Table of contents 4
5.Transmitter 5
6.Description of switch location and function 5
7.Transmitter battery 6
8.LED indicates 6
9.Gps & compass calibration notes. 7
10.X5 flight LED indicator 8
11.Stability and Agility Mode control inputs 9
12.Unlock process 10
13.Stabilize Mode 11
14.Direction lock 11
15.Althold 11
16.GPS loiter 12
17.RTL 12
18.Why need failsafe function 12
19.Quick start step 13
20.Flight control calibration 14
21.Outdoor cmpass calibration 15

GPS
Battery
Nose
Rear
LED indicator for APM controller
system working status
APM controller system
Receiver
Nose Rear
1045 Rotor 1045 Rotor (R)
1045 Rotor (R) 1045 Rotor

SW1
Channel-7 Channel-8
SW2
Bind
Mode 1
Mode 2
D/R
SW1
Channel-7Channel-8
Throttle & Rudder Stick Elevator & Aileron Stick
SW2
Bind
Mode 1
Mode 2
D/R
Press the button and power on the transmitter for binding.
Press the button, then there are Bi Bi Bi…. sounds, it indicate the radio change to mode1mode.
Press the button, then there are Bi Bi Bi… sounds, it indicate the radio change to mode2 mode.
Power on the transmitter, then press the button, it indicate the travel value changed to 60%(slow flight) when the sound Bi.
and it indicate the travel value changed to 100%(fast flight) when the sounds Bi Bi.
Bind
Mode 1
Mode 2
D/R
Stabilize mode.0
Altitude hold.1
Direction lock. 2
Stabilize mode.0
Altitude hold.1
Direction lock. 2
0.Stabilize mode
1.GPS loiter
2.GPS RTL
0.Stabilize mode
1.GPS loiter
2.GPS RTL

Sw1 location Sw2 location
7、Description of switch location and function：
8、Transmitter battery:
0
1
2
0
1
2
SW1 SW2 Function
0
1
2
0
0
0
0
0
1
2
Stabilize mode
Altitude hold
Direction lock
GPS loiter
GPS RTL
Rolling
Tilting
CH7
CH7

10.
LED indicator for APM controller
system working status

12

0
1
2
0
1
2
SW1&SW2 set at "0" SW1&SW2 set at "0"
Pulled the rudder switch and hit the bottom right corner of the bottom until the red flashing LED to relese.
SW1&SW2 set at "0"
13
14
Solid blue LED light indicate successful unlocking. Flashing red LED light indicate locking.
The propeller can not rotate when controller system is locking.

0
1
2
0
1
2
Sw1set at "2",sw2 set at " 0" .
Sw1set at "1",sw2 set at " 0" .
15
16

0
1
2
0
1
2
RTL
Sw1set at "0",sw2 set at "1" .
Sw1set at "0",sw2 set at "2" .
17
18
19

20
13
3

2.Move the Throttle & Rudder switch to the bottom right corner, after 12 seconds, quadcopter get into flight stabilized control calibration
mode when Blue Green change flashing. And then take off the quadcopter, keep hovering, the calibration is finished
when Gree LED stop fast flashing.
3

B C
D E F