Strata Corner Workstation User manual

Corner Workstation
Assembly Instructions
Flexible Options.Consistent Style. Enduring Quality.

STRATA ELECTRIC
2
Parts
A - Leg (3) B- Feet (2) C- Mid Post Base (1) D- Outer Frame Left (2)
Before beginning assembly of Strata Electric Corner Workstation, please ensure you have all
all of the below listed parts and in the specified quanties.
E - Outer Frame Right (2) F- Inner Frame (4) G- Top Side Frame Right (1) H- Top Side Frame Left (1)
I - Mid Post Frame Left (1) J- Mid Post Frame Right (1) K- Mid Post Bracket (1) L- Controller (1)
M - Wood Top Support (1) N- Cord Extension (1) O- Power Cable (1) P- Handset (1)

A
Image Screw Description Qty Tool
B
C
D
E
F
G
H
I
M6 x 15
4 x 25
5 x 20
M10 x 35
Leveler
Tailstock Screw
M6*8+BW
M5*8
M10*20
8
2
35
8
5
8
6
2
4
5mm Allen Wrench
Phillips Screw Driver
or Cordless Drill
Phillips Screw Driver
or Cordless Drill
5mm Allen Wrench
Hand
4mm Allen Wrench
4mm Allen Wrench
Phillips Screw Driver
or Cordless Drill
8mm Allen Wrench
3
Screws
Corner Workstation Assembly Instructions

STRATA ELECTRIC
4
Step 1
Attach Mid Post Frame Left (I) and Mid Post Frame Right (J) to a Leg (A) with 4 screws (G).
G
A
I J
Step 2
Attach Mid Post Bracket (K) to Mid Post Frame Left & Right (I & J) using 2 screws (G).
G
K

5
Corner Workstation Assembly Instructions
Step 3
Attach the Mid Post Base (C) to Leg (A) using 4 screws (I).
I
Step 4
Attach the Leveler (E) to the bottom of the Mid Post Base (C).
E
C
E

STRATA ELECTRIC
6
Step 5
Attach 2 of the Inner Frame (F) to the Mid Post Frame Left (I).
Step 6
Attach one each of the Outer Frame Left (D) and Outer Frame Right (E) to the Inner Frame (F).
F
F
I
D
F
F
E

7
Corner Workstation Assembly Instructions
Step 7
Repeat Step 5 and Step 6 on the opposite side for Mid Post Frame Right (J).
Step 8
Attach a Leg (A) to the Outer Frame Left (D) and Outer Frame Right (E) using two screws (A).
A
D
E
D
E

A
STRATA ELECTRIC
8
Step 9
Repeat Step 8 for the opposite side.
Step 10
Attach the Top Side Frame Left (G) and Top Side Frame Right (H) to both ends of the desk.
E
D
G
H

9
Corner Workstation Assembly Instructions
Step 11
Straighten both end Legs (A) upright.
Step 12
Screw 4 screws (A) into the Outer Frame Left (E) and Outer Frame Right (D) on both ends..
A
A
A

H
STRATA ELECTRIC
10
Step 13
Attach the Controller (L) to the frame at desired end using 2 screws (H).
Step 14
Attach the optional Wood Top Bracket (M) using 8 screws (C) if desired.
C
M

11
Corner Workstation Assembly Instructions
Step 15
Connect the Handset (P) cable to the Controller (L).
Step 16
Connect the Cable Extension (N) to the opposite end Leg (A).
O
N

STRATA ELECTRIC
12
Step 17
Connect all 3 Leg (A) cables to the Controller (L).
Step 18
Connect the Power Cable (O) to the Controller (L).
A
O

13
Corner Workstation Assembly Instructions
Step 19
Adjust frame to fit worktop.
Step 20
Secure the worktop using 27 screws (C). Screw the handset using 2 screws (B).
B
C
B
C

F
STRATA ELECTRIC
14
Step 21
Tighten the 8 screws (F) on the telescopic frame to firmly secure it to the right length.
Note: Screw F is preinstalled.
Step 22
Attach Feet (B) using 8 screws (D) then install the Levelers (E).
D
E
B B
E
E

15
Corner Workstation Assembly Instructions
Step 23
To finish setup, perform reset:
1. Press and hold down both Up and Down buttons on the Handset at the
same time for 3 seconds.
2. Continue pressing the buttons until all legs are in the lowest position.
3. When finished reset, the control box makes an alert sound, and the buttons can be
released.
Done!

Flexible Options.Consistent Style. Enduring Quality.