Street Furniture Aria User manual

Verison 1.0
aria
installation guide
12 November 2018
streetfurniture.com

© Street Furniture Australia Pty Limited ABN 46 070 910 100
streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
Welcome to the Aria System. Congratulations on
your purchase from Street Furniture Australia.
As Aria and its components are a modular system, there are many
configurations that can be customised. The following installation guide
is a general guide only and does not refer to your specific configuration.
Details will be provided separately on your chosen configuration and its
layout.
Before beginning installation please read through this guide thoroughly.
Important to note:
• Please ensure you have the correct configuration and components
before beginning, this information will be provided by our sales team.
• If you have purchased a PowerMe™ Table you must have a licenced
electrician perform the site preparation and installation.
• Ensure the orientation of the Aria Seats and Benches is correct before
fixing. Please refer to your site plan.
• Ensure the area where the seating is to be fixed is prepared and as
level as possible.
• Masonry bits and mounting fixtures are not included.
• Take care when handling the products to ensure no scratches, dents
or other damage occurs.
• In some cases the seats or benches will arrive with the axle and legs
removed, instructions for assembling these is on page 3.
understanding aria
Your Aria configuration comes with a code to identify its layout. It is important to understand this to ensure the
right components are received and layout is successful.
See below how to read your code:
1
2
3
S
B
R
C180
C90
C45
PM
CODE
1 Seater (600mm)
2 Seater (1200mm)
3 Seater (1800mm)
Seat (with backrest)
Bench (no backrest)
Reversed
Connector Panel 180°
Connector Panel 90°
Connector Panel 45°
PowerMe™ Table
DESCRIPTION
read left to right
2S-PM-2S-C45-2B
2S PM 2S 2BC45

© Street Furniture Australia Pty Limited ABN 46 070 910 100
streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
mounting detailspart descriptions
connector panels
axle clamp leg styles
axle cap axle
C180 C90
pedestal splay
C45
tools required
• Hammer drill and masonry bits.
• Allen key set.
• Safety equipment (glasses, gloves, boots).
• Surface fixing bolts (DynaBolts recommended).
seat and bench lengths
80mm
73
14.50
479
14.50
DynaBolt M12 recommended
(not included)
Sub-surface top hat included,
with fixings
Fill up to this level
hole centre distance (mm)
hole centre distance (mm)
480
600mm
540mm 1140mm 1740mm
1200mm 1800mm

© Street Furniture Australia Pty Limited ABN 46 070 910 100
streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
assembly instructions (1/3)
HOW TO ATTACH LEGS
In some cases your Aria System is delivered with the axle and legs
unattached to ensure safe delivery. Please follow the assembly steps
below.
1. Check you have all suitable legs, axle lengths and fasteners before
starting (this information will be provided separately based on your
order).
2. Position the seat or bench upside down.
3. Take the axle and position it according to Fig 1.
4. Position the axle caps as shown in Fig 2. Position the legs and/or
axle clamps, ensuring they are correctly oriented.
5. Tighten the bolts to ensure the axle is secured in place.
6. Once all legs are fixed, flip the bench or seat upright and proceed
with surface or sub-surface fixing.
Fig. 1 Fig. 2
Fig. 3 Fig. 4

© Street Furniture Australia Pty Limited ABN 46 070 910 100
streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
assembly instructions (2/3)
HOW TO CONNECT PANELS
If your Aria configuration includes the connector panels shown below,
please follow the steps below.
1. Position all seats and benches according to the specified layout.
2. Attach all connector panels as shown in Fig 1.
3. Once all products are positioned screw the connector panels to the
seat castings using the included M10x20 Bolts (4 per panel) and
washers as shown in Fig 2. Ensure bolts are tightened sufficiently.
4. With all panels fixed the seating arrangement can be surface or sub-
surface fixed.
C180 C90
end seat
casting
centre seat
casting
C45
Fig. 1 Fig. 2

© Street Furniture Australia Pty Limited ABN 46 070 910 100
streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
assembly instructions (3/3)
HOW TO INTEGRATE THE POWERME™ TABLE
If your Aria configuration includes a PowerMe™ Table, please follow the
steps below.
1. Remove products from packaging (ARIA 2S-PM-2S shown).
2. Connect the PowerMe Table/s to power. This work must be carried
out by a qualified electrician. Once the power is connected and
working the table can be fixed into place.
3. With PowerMe Table fixed in position - assemble the Aria Seats or
Benches into place according to your configuration as seen in Fig. 2.
4. Insert each opposing axle into the round key opening of the
PowerMe pedestal leg and ensure they meet face to face aligned to
the centre. Firmly tighten the 2 x M10 Hex Bolts using an Allen key
to fix the seats and/or benches in place, see Fig. 3.
5. Once the seat assembly is fixed together, proceed with surface or
sub-surface fixing it in place.
Tighten the two bolts in the
pedestal leg to clamp the
PowerMe Table in place.
Fig. 1 Fig. 2
Fig. 3 Fig. 4

© Street Furniture Australia Pty Limited ABN 46 070 910 100
streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
additional information
LARGE CONFIGURATION
If you have ordered a large configuration with multiple connector panels
and PowerMe Tables, the process will be similar but it is key that the site
is prepared before installation begins. Most importantly, power must be
available for the PowerMe Tables.
Using the configuration to the right as an example, below are important
notes and steps for a successful installation.
POWERME™ TABLE CONDUIT LOCATIONS
If your Aria configuration includes multiple PowerMe Tables you will
receive a coordinate map, similar to the figure on the right, to enable
correct location of an underground electrical conduit to provide power to
the tables.
This is a very important step to ensure your configuration can be assembled
correctly. Connect the PowerMe Tables to power as the first step.
DELIVERY AND INSTALLATION
For large configurations, you will receive your order in modules with the
legs detached (in most cases). Proceed to assemble the configuration
onsite according to the signed off drawing.
It is highly recommended to fully assemble your configuration in its
correct location BEFORE surface or sub-surface fixing.
x
y
Note:
If your conduit will not come from
below surface but above ground,
suitable openings will be provided on
the PowerMe pedestal leg to allow
power in.
upper
modules
PowerMe Tables
(boxed separately)