Streetwize Phone Holder User manual

Phone Holder
1
2
3
Will t smartphones between
49mm & 82mm wide.
Intention for Use
This product is intended for ONLY holding smartphones only
between the width of 49mm to 82mm. This gadget holder can
be mounted in three different ways: vent clip - mount, dashboard
adhesive mount & windscreen suction mount.
To get the best use of this product, we advise that you read all
information in this document.
Product Elements
1. Streetwize Universal Car Smartphone Holder
(with attached suction mount)
2. Adhesive pad for dashboard mount
3. Vent-clip mount
Never position the phone holder in a place that obscures the
view of the driver.

Mounting the gadget holder
As mentioned, this product can be
mounted in three different ways.
Please follow the instructions for
your preferred mounting option.
1.Windscreen Suction Mount
The windscreen suction mount
option already comes attached
out-of-the-box. To use this option,
simply unfold the gadget holder as
shown in (Fig 1).
Mount the suction cup to your
windscreen. Ensure the gadget
holder is unfolding towards you and
not facing downwards towards the
windscreen. Secure the suction
mount in place by turning the knob
behind the suction cup clockwise
(Fig 2).
Then place your phone into the
adjustable grip (Fig 3). The support
arms are spring loaded, simply pull
apart to the required width for the
phone, adjust the angle to your
requirements. With the suction
mount, you can rotate the device to
view the device either horizontally
or vertically.
To remove the suction mount from
your windscreen, simply turn the
knob anti-clockwise and pull one of
the tabs on the suction cup.
Fig 1
Fig 2
Fig 3

2. Dashboard Adhesive Mount
To mount the gadget holder to
your dashboard, get the supplied
adhesive pad (Fig 4), peel off the
red adhesive lm and then x it to
your dashboard. For added security
screw into place via the three screw
holes (screws NOT included).
Use the suction mount to secure the
gadget holder onto the dashboard
pad. Secure the suction mount in
place by turning the knob behind the
suction cup clockwise (Fig 5- A).
Then place your phone into the
adjustable grip. Adjust the angle to
your requirements. With the suction
mount, you can rotate the device to
view the device either horizontally or
vertically.
3. Vent-Mount Clip:
Please note, the phone holder will
not rotate when using the vent-clip.
You will need to remove the suction
cup mount from the phone holder.
Hold the device as per (Fig 6) and
position your thumbs behind the
adjustable arm of the holder. push
your thumbs forward until you hear
a click, the suction cup can
now be removed.
Fig 4
Fig 5
A
Fig 6

Assemble the vent clip by positioning
the vent grips (3) on the front cover
as shown in (Fig 7A). Simply place
the attachment end of the vent clip
through the hole in the middle and
slide either left or right (Fig 7B).
Then attach the vent clip to the
gadget holder (Fig 8).
Using the vent-mount clip, place the
gadget holder on to your vehicle’s
vent. Ensure the vent clip is secured
around the vent bars and the hinged
bottom support should be secured
into one of the vent bars at the
bottom as shown in (Fig 9).
Mount your phone horizontally.
Fig 7B
Fig 7A
Fig 8
Fig 9
For product support:
E: suppor[email protected]
T: [phone]
For trade enquiries:
E: [email protected]
T: [phone]
Streetwize: Ashburton Road West, Trafford Park, Manchester M17 1RY www.streetwizeaccessories.com
EU Registered address: The Ace Supply Co (Europe) Ltd, 25 Herbert Place, Dublin 2, D02 A098 Republic of Ireland.