Streetwize SWWL13 User manual

SWWL13
Buried
Folding
Parking Post
Read and understand these instructions before attempting any
operation of this parking post and retain for future reference!
INTENTION FOR USE
Thank you for purchasing the Streetwize Buired Folding Parking Post. This product is intended
for use as a visual deterrent and protects your vehicle against theft. This parking post can be
used to protect vehicles on driveways, car parks and caravan & motorhome parks.
This parking post can be placed in both hard and soft ground.
PRODUCT ELEMENTS
1. Streetwize Buried Folding Parking Post
2. Heavy-Duty Padlock with 2 keys
INSTALLING INTO SOFT GROUND
Requirements
• Shovel (or other digging equipment or tool)
• Fast drying concrete
• Stone
• Steel trowel
• Spirit Level
INSTRUCTIONS
1. With your shovel, dig a hole into the ground where you want to install the parking
post. When digging, ensure your hole is wide enough for the post and deep
enough for the spigot base (approx. 200mm). Ensure the locking base is
between 2 to 5mm above ground.
2. Use the stone to lay a foundation of around 20mm.
3. Set the spigot-base into the foundation.
4. Use the spirit level to check for vertical alignment.
5. Pour more stone into the base until 40mm below surface. Recheck vertical alignment.
6. Prepare the fast drying concrete.
7. Pour the concrete upto 5 mm below the locking base.
8. Use the trowel and some of the remaining unused concrete for finishing.

INSTALLING INTO HARD GROUND
Requirements
• Pneumatic Drill
• Shovel (or other digging equipment or tool)
• Fast drying concrete
• Stone
• Steel trowel
• Spirit Level
Instructions
1. For hard ground, use a Pneumatic Drill to dig a hole. Ensure your hole is wide enough for the post and deep
enough for the spigot base (approx. 200mm). Ensure the locking base is between 2 to 5mm above ground.
2. Use the stone to lay a foundation of around 20mm.
3. Set the spigot-base into the foundation.
4. Use the spirit level to check for vertical alignment.
5. Pour more stone into the base until 40mm below surface. Recheck vertical alignment.
6. Prepare the fast drying concrete.
7. Pour the concrete upto 5 mm below the locking base.
8. Use the trowel and some of the remaining unused concrete for finishing.
Locking/Unlocking the Parking Post.
When the parking post is ready to use, lift into position and align all the holes towards
the base of the post. Open the padlock by turning the key clockwise. Place through all
the holes (Fig 1) and turn the key anti-clockwise to lock the padlock on the parking post.
*Please take care of your keys as replacement keys are not available for
security reasons.
Health and Safety
• Please wear protective equipment, including gloves and eye protection
when installing the parking post.
• If you are kneeling on hard ground, we advise that you wear knee pads.
• When lifting rubble or other heavy object, please use correct procedure to prevent risk of injury
• When using the jackhammer, wear the correct protective equipment
Technical support
If you require any technical support, please contact us on [email protected] and provide the
product name and supplier code (see Technical Specifications) along with the technical query.
Technical Specifications
Product Streetwize Spigot-based Folding Bollard Post
Supplier Code SWWL13
Parking post height 600mm
Spigot base 200mm
Material Steel
Lock 60mm stainless steel padlock with 2 keys
Streetwize: Ashburton Road West, Trafford Park, Manchester M17 1RY
For product support: E: [email protected]
T: [phone]
For trade enquiries: E: [email protected]
T: [phone]
For spare parts: E: [email protected]
or contact us on our online form: www.streetwizeaccessories.com
Visit our website:
Or follow us on social media
We have over 1000 car and
leisure products in our range
Fig 1