Strictly Beds & Bunks Box B User manual

Assembly Instructions
Single Panel Bed Frames
www.strictlybeds.co.uk
Box B
Instructions 34
(version December 2020)
Bunk
Beds
Four Poster Beds
High Sleeper
Beds
Cabin Beds
Storage Beds
Mattresses
IN STOCK
IMPORTANT: of the
packaging until you are satisfied with your
purchase. . Please keep all cardboard until
fully assembled.
DO NOT DISPOSE

Clean out the Pre-drilled Holes
You have brought a solid pine product. During the drilling process
there may be sawdust still in the holes.
BEFORE you start assembly clear these holes with one of the bolts.
Push the bolt through each hole, this will dislodge any sawdust or
debris that could interfere with fixing the bed.
TOP TIPS - TOP TIPS
Read before you start assembly
NO YES
Locating the Dowel Rods
To keep the bed from rattling all the dowel holes have been
slightly mis-drilled by a couple of mm. When you push
parts together the dowels will straighten and pull together to
ensure a tight fit. Whenever you locate a dowel on the hole
NEVER push it all the way in, leave it so it is loose and can
be aligned with the second locating hole.
Push them all the way in and they will not line up.
GLUE SACHET INCLUDED
We have included a sachet of glue.
THIS IS NOT TO BE USED with the dowel rods.
Open the sachet and empty into a plastic container. Whenever
you connect a confirmat bolt (D) or a connector bolt (B) into a
barrel bolt (c) dip the end of the bolt in the wood glue and
screw in as normal. This will act as a lock tight and prevent the
bolt from working loose.
Applying a Finish to the Beds
The bed can be used in a natural form. However if you are applying
a stain or finish we advise that you build the bed first. When you are
happy with your purchase then put a sheet under the product and
apply your stain/paint to the manufacturers recommendations.
NOTE: we are unable to accept the return, under any circumstance
once a finish has been applied. By painting the bed you have
deemed to accept the quality.
Corner Posts -
Make sure the WHITE Mark is facing
upwards when laid on the floor
Headboard Facias-
These are colour coded
Please position as follows:
RED - At the top
WHITE - In the middle
BLUE - At the bottom
WHITE
BLUERED

How to identify your parts and fixings
All our products have four attachment methods. These are colour coded, at the end of each part
you will find a marker pen marking either RED, WHITE or BLUE
RED MARKING/FIXINGS
The part will have a red marker pen marking on the end.
Hole / Bolt configuration:
One large dowel hole - Place for large dowel
One small hole - Place for large 90cm confirmation bolt D
Areas used: top headboard facia
SIDE RAIL MARKING/FIXINGS
The part will have a blue marker pen marking on the
end.
Hole / Bolt configuration:
TWO large dowel holes - Place for large dowel
One small centre hole - Place for large 90mm connector
bolt C
Facing access hole - Place for barrel bolt B
BLUE MARKING/FIXINGS -
The part will have a blue marker pen marking on the
end.
Hole / Bolt configuration:
TWO large dowel holes - Place for large dowel
One small centre hole - Place for large 90mm connector
bolt D
Area Used: Bottom headboard Facia
INSERTING COLOUR PANEL
When locating the colour panel please ensure the
tongue of the panel is located at the back, ie on the
floor during assembly. This then covers unused holes
within the corner post.

Fixing List for assembly- Please note we use universal assembly
kits. You may find additional fixings left over or not required, please
dispose once the assembly has completed.
4
42
CUSTOMER CARE
We have checked all parts to ensure they are free of damage. However timber is a natural, living
product. Occasionally timber can still be adjusting to humidity, for this reason a crack or stretch mark
may appear after the product has been packaged.
Strictly Beds and Bunks however have a FREE PARTS REQUEST
service in this unlikely event. You need to order a part please go to
Parts Portal - www.strictlyhelpdesk.co.uk.
Email Assistance: [email protected]
Using the Camera on your phone scan this barcode
to take you our after sales. You can find various
options as regards assistance on this purchase.

Packing Note: Box 1 of 1
Cleveland Colour Panel Bed
Description Required
Part BS - Pack of 12 x Single Base Slats 1
Part 1 - Long Side rail 2
Part 13- Blue Headboard 1
Part 13G- Blue GROOVE Headboard 1
Part 15G- Red GROOVE Headboard 1
Part BP30 - COLOUR PANEL 1
Headboard Panel
Part TL Left Corner Headboard Post 1
Part TR Right Corner Headboard Post 1
Part BL Left Footboard Corner Post 1
Part BR Right Footboard Corner Post 1
Part 25- Siderail Support Legs 2
FIXING KIT & INSTRUCTIONS 34B 1
TL TR
15G
13G
BR
BL
13
25

Build the headboard
All corner posts will have WHITE chalk markings on
them with “L” or “R” on the bottom of each post. To
ensure the holes match you MUST have the WHITE
mark facing upwards when laying on the carpet. The “L”
post to the left, the “R” post to the right. Headboards fit
in order, from the top -
RED and, BLUE
** If in the wrong order the holes will not match up.**
CORNER POSTS - IMPORTANT - READ ME
We need to build the two headboards at either end of the bunk bed. You will find four corner posts,
two marked L-left, two marked R-right.. Separate into two piles, one left and one right.
Get one left and one right and lay as so face down on the carpet as shown above. You will note a
white chalk mark on each post, very important. This indicates the top of each post and the row of
holes that accepts the side/ guard rails.
You will have two headboard facias marked red and blue and a colour panel per headboard. Place
the blue facia at the bottom, then insert the panel the red facia at the top. The colour panel has a
tongue and groove lip, ensure this at the bottom facing downwards. Once in position Insert these
as per this picture. The fixings required for each insert are as follows:
Red: 1 x large confirmat 1 x Dowel rod
Blue: 1 x large confirmat 2 x Dowels
RED
BLUE
Tongue at Bottom
Build the Foot Board Each corner post will have a white chalk marking, lay
the post down and have the marking facing you to the
top. BL goes to the left, BR goes to the right. Now
grab the headboard insert 1x 13 (blue) and attach

It is important this leg is attached as it supports
the side rail.
Measure a half way point on the side rail. Place the support leg
under the side rail from the outside. Using two black screws
attach from the inside of the side rail. Note there is no access hole
as the screws are self threading
Attach support legs
The centre leg will hover slightly off the floor,
when the bed is in use it will move down and
support the bed. This is to protect the leg if
the bed moves.
Attach the side rails
The side rails are universal, left or right. Firstly ensure there is no sawdust or debris in the access holes. Using a
bolt push through to clear. Now insert the dowel rods at all ends, do not push all the way in.
With the help of a second person start from the right side and attach to the head and footboard to the side rails.
Place the barrel bolt within the round access hole on the side rail. Now dip bolt B into the glue and push through
to connect to the barrel bolt. This side rail is designed not too move so the fixing is tight.
Note: If you have ordered a guest bed simply do not attach the front side rail support leg to
the front Side rail. If you have ordered a storage option further instructions and fixings
will be found in a separate box.
You will have twelve extra wide base slats. Push the first slat tight
with the footboard corner posts, then using the base slat spacer block
evenly space out the remaining base slats. DO NOT SCREW IN
PLACE YET.
Now push the slats flush to the left hand side rail and screw in (do
not screw the right hand side yet). Now go to the right hand side and
start with the slat near the centre. Push the side rail in so the slat is
flush, then fix using the screw. This aligns the side rail. Now fix the
remaining base slats.
Attach the base slats
Mattress Selection Available
Strictly Beds has a full range of mattresses to fit this bunk bed. This model has been
designed to take a thicker 20cm mattress.
To go to our selection please type in
www.strictlbedsandbunks.co.uk/mattress
Using the Camera on your phone scan this barcode
to take you our mattress selection