Strictly Beds & Bunks Athens Single Bed User manual

Athens Single Bed
Assembly
Instructions
IMPORTANT: of the packaging until you
are satisfied with your purchase.
DO NOT DISPOSE
Assembly Instructions
IMPORTANT – READ CAREFULLY –
RETAIN FOR FUTURE REFERENCE
CUSTOMER CARE
We have checked all parts to ensure they are free of damage. However timber is a
natural, living product. Occasionally timber can still be adjusting to humidity, for this
reason a crack or stretch mark may appear after the product has been packaged.
Strictly Beds and Bunks however have a
FREE PARTS REQUEST
service in this unlikely event. You need to order a part please go to our FREE help
desk www.strictlyhelpdesk.co.uk.
Assistance: [email protected]
Instructions: 22
Box B

9
9
9
10
12
1M
AL AR
STR
STL
Packing Note: Athens Single
Description Required
Part 1- Long Side rail 2
Part 9- Headboard Facia (4G) 4
AL Left Corner Post 1
AR Right Corner Post 1
STL Left Footboard Corner Post 1
STL Right Footboard Corner Post 1
Part 25- Siderail Support Legs 2
Part 12- Long Shaker Inserts 6
Part 10- Short Shaker Inserts 6
Pack of single base slats 1
FIXING KIT 1

To ALL customers - If you have a missing or damaged bolt you can order these FREE
of CHARGE using the following method,
please note we will require your order number or delivery address
Email: [email protected]
Website: www.strictlyhelpdesk.co.uk
All fixings are sent out via next day Royal Mail Post

Build the headboards PIC 1 - First Select the top headboard posts.
These will be marked AL ( lay on the left side)
and AR (lay on the right side). IMPORTANT:
These posts will have a white chalk marking,
these MUST be facing you and at the top when
laying on the carpet.
You will also see two headboard facias marked
red 4G and headboard inserts. Place as shown
in the PIC 1.
Pic 1
Place dowel rods in all the
headboard inserts as described
above. Then push fit them
together with the two headboard
facias. This now completed the
headboard facia.
Locate the dowel rods as described above to
each corner post. Remember, post marked with
an L is on the left, R is on the right. Using BOLT
B and C push the connector bolt through the
corner post. Locate the barrel not inside the circle
hole and screw together.
Build The Footboards - The process is exactly the same however using
the smaller headboard inserts and the bottom corner posts STR and
STL
Attach the side rails (NO centre rail)
The side rails are universal, left or right. Firstly ensure there is no sawdust or
debris in the access holes. Using a bolt push through to clear. Now insert the
dowel rods at all ends, do not push all the way in.
With the help of a second person start from the right side and attach to the head
and footboard to the side rails. Place the barrel bolt within the round access hole
on the side rail. Now dip bolt B into the glue and push through to connect to the
barrel bolt. This side rail is designed not too move so the fixing is tight.

Attach the base slats, please see the covering
colour leaflet for full details.
TIP:-When you have attached the base
slats you will have additional base slats screws.
Out of the 12 slats screw 4 of them directly into the
centre rail. Using the base slat screws simply drill
through the top of the base slat into the centre rail.
This will further strengthen the bed.
Attach the side rail support legs
It is important this leg is attached as it
supports the side rail.
Measure a half way point on the side rail. Place the
support leg under the side rail from the outside. Using two
black screws attach from the inside of the side rail. Note
there is no access hole as the screws are self threading
The centre leg will hover slightly off the
floor, when the bed is in use it will move
down and support the bed. This is to
protect the leg if the bed moves.
If you have ordered a guest bed simply do not attach the from side rail support leg.