Strictly Beds & Bunks Cabin Bed User manual

Assembly Instructions
Cabin Bed
Study Desk and Chair Set
KIT P
Instructions:
30
(Version September2020)
www.strictlybeds.co.uk
IMPORTANT: of the
packaging until you are satisfied with
your purchase. . Please keep all
cardboard until fully assembled.
DO NOT DISPOSE

Clean out the Pre-drilled Holes
You have brought a solid pine product. During the drilling
process there may be sawdust still in the holes.
BEFORE you start assembly clear these holes with one of the
bolts. Push the bolt through each hole, this will dislodge any
sawdust or debris that could interfere with fixing the bed.
TOP TIPS - TOP TIPS
Read before you start assembly
NO YES
Locating the Dowel Rods
To keep the bed from rattling all the dowel holes have
been slightly mis-drilled by a couple of mm. When you
push parts together the dowels will straighten and pull
together to ensure a tight fit. Whenever you locate a
dowel on the hole NEVER push it all the way in, leave
it so it is loose and can be aligned with the second
locating hole.
Push them all the way in and they will not line up.
GLUE SACHET INCLUDED
We have included a sachet of glue.
THIS IS NOT TO BE USED with the dowel rods.
Open the sachet and empty into a plastic container.
Whenever you connect a confirmat bolt (D) or a
connector bolt (B) into a barrel bolt (c) dip the end of the
bolt in the wood glue and screw in as normal. This will act
as a lock tight and prevent the bolt from working loose.
Applying a Finish to the Beds
The bed can be used in a natural form. However if you are
applying a stain or finish we advise that you build the bed first.
When you are happy with your purchase then put a sheet
under the product and apply your stain/paint to the
manufacturers recommendations.
NOTE: we are unable to accept the return, under any
circumstance once a finish has been applied. By painting the
bed you have deemed to accept the quality.
Chair and Table Legs
Make sure the WHITE Mark is facing
upwards when laid on the floor

Contents List
CBL
CBR 2
1
3
DL
DR
3
4
6
5
CFR
CFL
7
CUSTOMER CARE
We have checked all parts to ensure they are free of damage. However timber is a
natural, living product. Occasionally timber can still be adjusting to humidity, for this
reason a crack or stretch mark may appear after the product has been packaged.
Strictly Beds and Bunks however have a
FREE PARTS REQUEST
service in this unlikely event. You need to order a part please go to our FREE help desk
www.strictlyhelpdesk.co.uk.
Assistance: [email protected]
Fixings
Packing Note: DCS1
Description Required
DESK
Part DL - Table Leg LEFT 2
Part DR - Table Leg RIGHT 2
Part 1 - Top Short (410mm) Apron 2
Part 2- Bottom Short (410mm) Apron 2
Part 3 - Top LONG (700mm) Apron 2
Part DT - MDF 12mm Grooved desk top 1
CHAIR
Part CBL - Chair back LEFT leg 1
Part CBR - Chair back Right leg 1
Part CFL - Chair front LEFT leg 1
Part CFR - Chair front Right leg 1
Part 4 Lower seat Apron (sides) 2
Part 7 Lower seat Apron (front/back) 2
Part 5 Middle Cross Rail 1
Part 6 Top Cross Rail 1
Part CS - MDF 12mm Chair seat base 1
Assemble Instructions and Fixing kit P 1

DL DR
Build The Desk Desk - Build The Two Ends
Place two table legs on the carpet, DL to your left and DR to your right.
IMPORTANT, ensure the white markings are facing upwards and located at the
top. Position Part 1 with the groove facing you at the top. Position Part 2 at the
bottom of the posts.
Inside bolt A (dowel) in each end of the these parts 1 and 2)and align with the
dowel holes on each post. Dip Bolt D into the glue and push the holes of each
corner post ,two per post and tighten. Now repeat and build the second end.
Now Attach the Two Long Aprons and Desk Top
Now lay one end down, white markings facing
you. Attach Part 2 as shown using fixings A and
D, ensure the groove slot is at the top matching
the ends. Slide the desk top in, again ensure
the lip is at the bottom. Now attach the second
end using bolts A and D
1
2

7
5
6
CBRCBL
Build The Chairs
Lay on the carpet part CBL to the left, CBR
to the right. Ensure both the white chalk
markings are facing front.
Now position parts 4 , 5 , and 7 as shown.
Please ensure the groove on part 4 is facing
upwards to the top. Now apply all the
dowels (A). Now screw together using bolt
D.
Now attach another two Part 4 to the
left and right. Again ensure the
Grooves are facing inwards and are
located at the top.
Now slide the chair seat into the
grooves of the panel. Please ensure ,
as with the desk the ticker part of the
panel is facing upwards.
Lay on the carpet part CFL to the left, CFR to the right.
Ensure both the white chalk markings are facing front.
Now position parts 7 as shown. Please ensure the
groove on part 7 is facing upwards to the top. Now
apply all the dowels (A). Now screw together using
bolt D. Once built place on top and attach to complete
the assembly.
7
7
444
CFL CFR
7
4