Stumpfl Fullwhite Curve User manual

10GS
FULLWHITE CURVE
MANUAL

ACCESSORY BAG
Yellow bag for mounting accessories
CURVED HORIZONTAL
ELEMENTS
Consists of plug in elements with integrated
pin-lock screw connection
ASSEMBLY INSTRUCTION

FOLDABLE CENTER SUPPORT
VERTICAL FRAME ELEMENTS
BASIC FRAME
Modular plug-in frame system
Frame components in custom length
4x corner parts 34x52cm

INDEX
SCOPE OF DELIVERY 2
GENERAL 5
OVERVIEW 6
FULLWHITE CURVE FRAME COMPONENTS 7
HORIZONTAL FRAME SECTIONS 8
CORNER ELEMENTS 10
VERTICAL FRAME ELEMENTS 11
TOP FRAME SECTION & CENTER SUPPORTS 12
SURFACE ATTACHMENT 13
FRAME COMPLETION 14
LEG ATTACHMENT 14
ACCESSORIES 16
4

QUALITY AND SAFETY:
This projection screen is in accordance with the safety regulations in DIN standard 19045 and DIN 56950.
The screen fabric is comply with DIN 4102 part 1 and the specications of the according data sheet.
WARRANTY:
The warranty period for production deciencies is 5 years for the frame elements and 24 months
for the projection surface. The projection screen is developed for indoor use only. Any damage and
consequential damage caused by outdoor use is not covered by warranty.
FRAME ELEMENTS:
The frame elements, accessories and additional elements are maintenance-free!
PROJECTION SURFACE:
The projection surface is packed into a separate soft bag to avoid any damage by the frame parts,
bleaching and discoloration. Additionally following handling instructions have to be adhered to:
! Do not bring printed and coloring objects (instructions, magazines, etc.) in contact with the
projection surface
! Do not mark the projection surface!
Colors penetrate the projection surface and cannot be cleaned anymore!
Store the projection surface cleaned and dry at room temperature only!
COLD BREAK
A projection foil must never be stored or transported below 0 ° C. There is a risk of a cold break! The
lm becomes very brittle and splinters like glass! When transporting the projection surface at low
temperatures, do not mount the surface unless it has reached its full elasticity at room temperature.
Otherwise there is the risk of cold break of the projection screen.
CLEANING OF THE PROJECTION SURFACE:
Use a white clean cotton cloth saturated with clear water (optionally mild soap water) and wipe the area
gently in one direction (no circular motion). Wipe dry with another cotton cloth.
To clean a stubborn stain, use methylated spirit and follow the same procedure.
Clean rear projection surfaces in case of imperative only!
Subject to modications, errors expected !
GENERAL
5

231
OVERVIEW
CURVED CONNECTIONS
Curved horizontal parts are connected by locking pins with conical grooves for a gap-free assembly.
Additional wedge clamps ensure a perfect alignment of the prole edges.
SYSTEM COMPONENTS:
The hollow chamber prole with trapezoid shape gives an extra high stability and allows a perfect
wrinkle-free application of the projection surface on the backside of the prole with hooks.
VERTICAL CLAMP CONNECTIONS
The Fullwhite clamp connector is equipped with two clamp screws (1&2) and a center safety screw (3).
clamp connector with
clamping prole (red)
clamp screws safety screw
6

1
14
1
14
2
13
3
12
5
10
4
11
6
9
7
8
2
13
3
12
5
10
4
11
6
9
7
8
FULLWHITE CURVE FRAME COMPONENTS
FULLWHITE CURVE
All components are labeled and/or numbered. Numbering starts with the left top corner in clockwise
direction.
Required tools are enclosed:
• 5mm hexagonal screwdriver
• 3mm hexagonal screwdriver
• Torx TX25 screwdriver
Depending on screen size we recommend to use stepladders to ease the assembly.
It is recommended to set up the frame on squared timbers or similar to avoid damages of
the prole edges.
7

1
3 4
5
2
HORIZONTAL FRAME SECTIONS
1-3 Assembled horizontal frame sections
4Assemble the upper and lower horizontal
elements according to the numbering.
4-6 Plug together equal numbered parts
and slightly screw in the two set screws with
the 5mm hexagonal screwdriver so that the
connection is secured, but do not fasten.
b
o
t
t
o
m
f
r
a
m
e
s
e
c
t
i
o
n
t
o
p
f
r
a
m
e
s
e
c
t
i
o
n
8

6 7
98
10
7-8 Next tighten the wedge clamp until the
prole edges are perfectly aligned.
9-10 Now fasten the two 5mm hexagonal set
screws completely.
Repeat this step until both horizontal sections
are completed.
9

1
3 4
2
CORNER ELEMENTS
BOTTOM LEFT
TOP LEFT
BOTTOM RIGHT
TOP RIGHT
1-4 Now attach the corner parts on both sides of the already assembled bottom and top horizontal
frame sections.
10

1
3
5
4
2
VERTICAL FRAME ELEMENTS
BOTTOM LEFT BOTTOM RIGHT
1-2 Plug in the rst vertical frame element on
each side of the bottom corners.
Tighten the two clamp screws 3-4 and secure it
with the center safety screw 5.
11

3
1
2 3
TOP FRAME SECTION & CENTER SUPPORTS
vertical element
vertical element
corner top-right
corner bottom-right
center support
top frame section
bottom frame section
1-3 Next connect the rst vertical element to each corner of the top frame section and bolt the center
supports at the appropriate labeled positions.
12

SURFACE ATTACHMENT
Unfold the projection surface with, according to
the screen size appropriate number of people.
Start to hook in the projection surface at one
corner. Make sure that the lateral hooks are
secured by the black plastic corner clip.
Lift the screen and plug in the next vertical
frame elements and unfold the next part of
the center supports. Secure the lateral vertical
frame elements and hook the projection surface
further down.
Once the rst corner is covered properly you
can attach the surface to the top horizontal
frame section. Attach one hook by the other
while sliding the projection surface with several
people gently till the opposite corner.
Then attach the hooks on the lateral frame
element. Avoid to projection surface to touch
the ground during the entire attachment.
13

2
3
1 2
FRAME COMPLETION
LEG ATTACHMENT
1-2 When assembly of all vertical frame elements is completed lift the screen at the the vertical parts
and the center supports and connect the screen to the bottom frame section.
Secure the two vertical frame connections and bolt the center supports to the bottom frame.
Attach the legs to the threaded round spacers of the center supports in the desired height, with the
delivered wing screws. Once the Fullwhite curve is on legs the attachment of the projection surface can
be nished.
14

MOUNTING OPTIONS
MOUNTING BRACKET FOR WALL
MOUNTING
Optional as vertical or horizontal mounting point
MOUNTING BRACKET FOR CEILING
SUSPENSION
3
PIVOT NUTS
ACCESSORIES
General attachment of pivot Nuts M8 with exible tongue
(Dierent to the illustration above, the pivot Nuts M8 for SET UP SUPPORT is equipped with a spring
loaded ball)
15

AV Stump GmbH | Mitterweg 46 | 4702 Wallern
AVstump@AVstump.com | www.AVstump.com | [phone]