Sub-Zero Built-in Series User manual

Built-In Series Overlay Door Panel Retro-Fit Kit - For Over/Under Models
(7003402, 7003403)
7007804 / Rev A / January, 2008
Page 1 of 3
CONTAINS: QTY DESCRIPTION
2 Refrigerator Door Side Trim Filler
1 Refrigerator Door Bottom Trim Filler
1 Freezer Drawer Bottom Trim
2 Freezer Drawer Side Trim Filler
2 Panel Grille Side Trim Filler
1 Instruction Sheet
1
4
2
5
6
3
BI SERIES
DOOR
EXISTING
DOOR
PANEL
BOTTOM TRIM FILLER
HINGE SIDE
TRIM FILLER
HANDLE SIDE TRIM FILLER
HANDLE-SIDE TRIM
SCREWS
SCREW COVER
DOOR
SCREW COVER
HANDLE-SIDE TRIM
REFRIGERATOR DOOR HANDLE-SIDE TRIM REMOVAL:
1. At the top of the door, insert a flat blade screwdriver into the chan-
nel of the screw cover and push the cover away form the handle-
side trim, disengaging it from the trim (See Figure 1).
2. With a T-20, 6-lobe Torx type bit, extract the handle-side trim
mounting screws and pull the trim from the door (See Figure 2).
DOOR COMPONENTS INSTALLATION PROCEDURE(See Figure 3):
1. Install one Refrigerator Door Side Trim Filler so that it overlaps the
hinge side door trim.
2. Install the Refrigerator Door Bottom Trim Filler so that it overlaps
the bottom door trim and hooks behind the Trim Filler on the hinge
side, then secure the ends with masking tape until after the panel
is installed.
3. Install the existing 600 series door panel, then remove the tape as
mentioned in step 2 above.
4. Install the other Refrigerator Door Side Trim Filler over the edge of
the door panel on the handle side of the door.
5. Reattach the handle-side door trim.
6. Reinstall the screw cover.
Figure 1. Screw Cover Removal
HANDLE-SIDE TRIM
Figure 2. Handle.Side Trim Removal
Figure 3. Door Component Installation

BI SERIES
DRAWER
EXISTING
DRAWER
PANEL
BOTTOM
TRIM
SIDE TRIM
FILLER (2)
TOP TRIM
SCREWS
SCREW COVER
2
1
2
3
4
5
SCREWS
Figure 7. Drawer Component Installation
Built-In Series Overlay Door Panel Retro-Fit Kit - For Over/Under Models
(7003402, 7003403)
7007804 / Rev A / January, 2008
Page 2 of 3
SCREW COVER
HANDLE-SIDE TRIM
FREEZER DRAWER TRIM REMOVAL PROCEDURE:
1. At the back right-hand side of the top drawer trim, insert a flat blade screwdriver into the notch in the screw
cover and pry the cover away form the top trim, disengaging it from the top trim (See Figure 4).
2. With a T-20, 6-lobe Torx type bit, extract the top trim mounting screws and pull the top trim from the drawer
(See Figure 5).
3. With a T-15, 6-lobe Torx type bit, extract the bottom trim mounting screws and pull the bottom trim from the
drawer (See Figure 6).
DRAWER COMPONENTS INSTALLATION PROCEDURE (See Figure 7):
1. Install the new Freezer Drawer Bottom Trim reusing the screws just removed in step 3 above.
2. Install both Drawer Side Trim Fillers so that they overlap the side trim and hook up with the bottom Trim.
3. Install the existing 600 series drawer panel.
4. Reattach the top drawer trim.
5. Reinstall the screw cover.
Figure 4. Screw Cover Removal
DRAWER
TOP DRAWER TRIM
Figure 5. Top Trim Removal
DRAWER
BOTTOM TRIM
Figure 6. Bottom Trim Removal

Built-In Series Overlay Door Panel Retro-Fit Kit - For Over/Under Models
(7003402, 7003403)
7007804 / Rev A / January, 2008
Page 3 of 3
BEFORE BEGINNING WORK ON THE PANEL GRILLE
ASSEMBLY, READ THESE IMPORTANT NOTES:
• The existing 600 Series grille front panel, spacer panel
and backer panel will need to be cut down by 1” (25 mm)
in height in order to fit into the Built-in Series panel grille
frame.
• If cutting the grille panel assembly down is not an option,
then an alternate Built-in Series louvered grille assembly
or stainless steel grille assembly should be considered.
BOTTOM GRILLE FRAME
EXTRUSION REMOVAL PROCEDURE (See Figure 8):
Use a T-20, 6-lobe Torx type bit to extract the two lower grille
frame extrusion mounting screws from each side of the grille
and pull the bottom grille extrusion along with the corner
brackets from the side grille extrusions.
GRILLE COMPONENTS
INSTALLATION PROCEDURE (See Figure 9):
1. Install both Panel Grille Side Trim Fillers so that they over-
lap the grille’s side trim.
2. Install the existing 600 series grille panel assembly after it
has been cut down by 1” (25 mm) in height.
3. Reattach the bottom grille extrusion.
BOTTOM GRILLE
FRAME EXTRUSION
PANEL GRILLE
FRAME ASSEMBLY
SCREWS
(2 OF 4)
Figure 8. Bottom Frame Extrusion Removal
BOTTOM GRILLE
FRAME EXTRUSION
PANEL GRILLE
FRAME ASSEMBL
Y
EXISTING GRILLE PANEL
after being cut down 1” (25 mm)
SIDE TRIM
FILLER (2)
11
2
3
Figure 9. Grille Component Installation