Sub-Zero 700BCI User manual

USE & CARE GUIDE
Integrated Refrigeration

Important Note
To ensure the safe and efficient use of Sub-Zero equip-
ment, please take note of the following types of highlighted
information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION signals a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
Contents
Integrated Refrigeration .......................... 3
Integrated Features .............................. 4
Integrated Models ............................... 5
Integrated Use & Care ........................... 10
eeping Food at Its Best ........................ 21
Food Storage Recommendations ................. 25
Troubleshooting Guide .......................... 31
Service Information ............................. 34
Sub-Zero Warranty ............................. 35
eatures and specifications are subject to change at any time
without notice. Visit our website, subzero.com for the most
up-to-date information.

Integrated Refrigeration 3
subzero.com
Thank You
Thank you for purchasing your new Sub-Zero integrated
unit. With Sub-Zero, you can rely on a 60-year tradition of
quality and reliability. The integrated line brings together
the latest and finest features in home refrigeration to give
you the freshest food possible.
Your Sub-Zero is protected by a warranty that is one of
the finest in the industry. Take a moment to read the
warranty statement at the end of this guide and refer to
it should service become necessary.
This use & care guide will answer most of your questions
about the features, operation and maintenance of your
integrated unit. If you have questions that are not
addressed here, call Sub-Zero customer care at
800-222-7820 or visit our website, subzero.com.
Integrated Refrigeration
The Sub-Zero integrated line brings you true innovation!
It is the first integrated systems approach to domestic
refrigeration, offering you three significant advantages.
•Integrated refrigeration systems gives you the choice
of refrigerator or freezer options to meet your needs.
The ergonomic division of space increases your access
to storage areas.
•Integrated refrigeration systems gives you the choice
of location of refrigeration units throughout your
kitchen and home. This helps you meet your individual
needs for the way you use refrigeration within your
home.
•Integrated refrigeration systems gives you total
aesthetic integration with cabinets you have chosen.
Refrigeration units, in essence, are refrigeration
cabinets. They literally become a part of the kitchen
furniture.

Integrated eatures 4
Integrated eatures
•Integrated refrigeration systems offer “point-of-use”
refrigeration that integrates with cabinetry anywhere in
the home.
•Integrated combination units, except model 700BC(I),
have the Sub-Zero dual refrigeration system, which
ensures the freshest food and energy efficiency at the
same time. You have precise independent control of
the refrigerator and freezer sections.
•Integrated models meet strict Department of Energy
requirements.
•A microprocessor controls all electronic functions,
including temperature, adaptive defrost, lights, cooling
fan and door/drawer ajar warning. Electronic digital
controls lets you monitor and adjust all temperature
zones in the unit.
•Seamless molding forms the front of each unit’s
interior, giving a sculptured look that is both utilitarian
and elegant.
•lat to the ceiling, superior lighting provides white,
efficient light in the top compartment and drawers.
•A single sculptured molding, with tempered glass
molded into it, forms each sealed, adjustable shelf.
This design feature prevents spills from dripping
throughout the unit.
•The enclosed deli drawer gives you a convenient area
for deli foods or other small items.
•Models IC-27R and 736TCI have a sealed crisper with
removable dividers. It is large and deep, with smooth
sides for easy cleaning.
•A divided dairy compartment is standard on model
IC-27R and tall refrigerator and combination units. This
adjustable compartment is a convenient place for dairy
foods and small items that need a fresh environment.
•All column and tall models have adjustable door
shelves. Column models also feature shallow door
shelves.
•An interchangeable lift-up crisper cover provides for
maximum humidity in the base and tall refrigerator
units and in the upper refrigerator drawer of base
combination units, helping you keep produce at its
best quality, longer. The middle drawer of column
model IC-27R is a sealed crisper.
•or models with an automatic ice maker, the clear
molded ice container is easily removable.
•The dual-action hinge has a built-in 90° door stop.
•Sub-Zero products are covered by a two, five and
twelve year residential warranty (exclusions apply).
See warranty details at the end of this guide.
Drawer models are certified by Star-K to meet
strict religious regulations in conjunction with
specific instructions found on www.star-k.org.
Column and tall models require installation of
a harness kit. or details about the harness
kit, contact your authorized Sub-Zero dealer.

Integrated Models 5
subzero.com
Model IC-27R
ALL REFRIGERATOR COLUMN
User reference
card
Adjustable spill-
proof glass shelves
Electronic digital
control panel
Adjustable dairy
compartment
Seamless
molding
Stationary shelf
Adjustable door
shelves
Magnetic door
gaskets
Shallow door
shelves
Kickplate/grille
Refrigerator
storage drawers
High-humidity
crisper drawer
Location of
rating plate
Model IC-27 I
ALL FREEZER COLUMN
Ice storage
container
Adjustable wire
shelves
Electronic digital
control panel
Seamless
molding
Stationary shelf
Adjustable door
shelves
Magnetic door
gaskets
Adjustable shallow
door shelves
Kickplate/grille
reezer storage
drawers
Location of
rating plate
Automatic ice
maker

Integrated Models 6
Model 700TR
ALL REFRIGERATOR
Removable
crisper cover
Adjustable glass shelf
and deli drawer
Adjustable spill-
proof glass shelves
Electronic digital
control panel
Adjustable dairy
compartment
Seamless
molding
Adjustable door
shelves
Lower refrigerator
storage drawer
Upper refrigerator
storage drawer
Kickplate/grille
Magnetic door
and drawer gaskets
Location of rating
plate
Stationary shelf
Removable
crisper cover
Kickplate/grille
Adjustable glass shelf
and deli drawer
Adjustable spill-
proof glass shelves
Electronic digital
control panel
Adjustable dairy
compartment
Seamless
molding
Magnetic door
and drawer gaskets
Location of rating
plate
Adjustable door
shelves
Stationary shelf
Lower refrigerator
storage drawer
Upper refrigerator
storage drawer
Model 736TR
ALL REFRIGERATOR

Integrated Models 7
subzero.com
Model 700T I
ALL FREEZER
Magnetic door
and drawer gaskets
Kickplate/grille
Adjustable wire
shelves
Electronic digital
control panel
Seamless
molding
Automatic
ice maker
Location of rating
plate
Adjustable door
shelves
Stationary shelf
Lower freezer
storage drawer
Upper freezer
storage drawer
Model 736T I
ALL FREEZER
Magnetic door
and drawer gaskets
Adjustable glass
shelves
Electronic digital
control panel
Seamless
molding
Adjustable door
shelves
Lower freezer
storage drawer
Upper freezer
storage drawer
Kickplate/grille
Automatic
ice maker
Location of rating
plate
Stationary shelf

Integrated Models 8
Model 700TCI
COMBINATION REFRIGERATOR / FREEZER
Model 736TCI
COMBINATION REFRIGERATOR / FREEZER
Magnetic door
and drawer gaskets
Kickplate/grille
Adjustable spill-
proof glass shelves
Electronic digital
control panel
Adjustable dairy
compartment
Seamless
molding
Automatic
ice maker
Location of rating
plate
Adjustable door
shelves
Crisper drawer
Lower freezer
storage drawer
Upper freezer
storage drawer
Magnetic door
and drawer gaskets
Adjustable glass shelf
and deli drawer
Adjustable spill-
proof glass shelves
Electronic digital
control panel
Adjustable dairy
compartment
Seamless
molding
Adjustable door
shelves
Lower freezer
storage drawer
Upper freezer
storage drawer
Kickplate/grille
Automatic
ice maker
Location of rating
plate
Stationary shelf

Integrated Models 9
subzero.com
Lower freezer
storage drawer
Magnetic drawer
gaskets
Location of rating
plate
Seamless molding
Electronic digital
control panel
Removable
crisper cover
Kickplate/grille Automatic ice maker
(model 700BCI)
Upper refrigerator
storage drawer
Lower freezer
storage drawer
Magnetic drawer
gaskets
Location of rating
plate
Seamless molding Electronic digital
control panel
Kickplate/grille
Automatic ice maker
(model 700B I)
Upper freezer
storage drawer
Magnetic drawer
gaskets
Location of rating
plate
Seamless molding
Electronic digital
control panel
Removable
crisper cover
Kickplate/grille Lower refrigerator
storage drawer
Upper refrigerator
storage drawer
Model 700BR
REFRIGERATOR DRAWERS
Model 700B (I)
FREEZER DRAWERS
Model 700BC(I)
REFRIGERATOR / FREEZER DRAWERS

Integrated Use & Care 10
Electronic Control System
The electronic control system of your Sub-Zero integrated
unit provides you with the best control of your refrigerated
foods. By maintaining recommended refrigerator and
freezer temperatures, you can keep food safe and retain
the best quality possible.
A microprocessor accurately controls the temperature of
the cooling zones. It samples the temperature every
second and makes adjustments to maintain the tempera-
ture you have indicated.
The electronic control panel is located on the top of
column and tall models, and in the top drawer of drawer
models. All of the essential controls and information are
displayed in this easy-to-reach-and-see panel. Refer to
the illustrations below for location of the electronic control
panel. Note that for single zone units and units that cannot
support an ice maker, the electronic control panel will be
slightly different.
LCD DISPLAY
The liquid crystal display (LCD) located on the electronic
control panel shows the actual temperature of different
zones in your unit.
If there is a temperature or ice maker problem, you’ll be
alerted by a flashing SERVICE indicator light in the LCD
display.
TEMPERATURE CONTROL
Integrated units are factory preset to maintain refrigerator
zones at 38° (3°C) and freezer zones at 0° (-18°C). The
temperature range for refrigerator zones is 34° (1°C) to
45° (7°C) and the temperature range for freezer zones is
-5° (-21°C) to +5° (-15°C).
or combination models, there are two sets of WARMER
and COLDER key pads on the electronic control panel.
One is for the upper refrigerator zone and the other for the
lower freezer drawers. Models 700TR and 736TR also
have two sets of key pads, one for the upper zone and the
other for the drawers. Column models and single-zone
refrigerator and freezer units have only one set of
WARMER and COLDER key pads.
The COLDER key pad allows you to decrease the temper-
ature of a selected zone in one-degree increments.
Similar to the COLDER key pad, you can raise the temper-
ature in any zone in one-degree increments by pressing
the WARMER key pad.
IMPORTANT NOTE: Always allow 24 hours for the unit to
reach the temperature you set.
POWER
The UNIT ON/O key pad (POWER for column models),
located on the electronic control panel, will turn off all
electrical power to the unit. This key pad can be used for
shutting down the unit for servicing or extended vacations.
Control panel (tall model
shown).
Drawer unit control panel.
COLDER WARMER REFRIGERATOR
FREEZER COLDER WARMER
ICE
ON/OFF ON/OFF
UNIT
ON/OFF

Integrated Use & Care 11
subzero.com
Electronic Control System
ICE MA ER CONTROL
The ICE ON/O key pad, located on the electronic
control panel, turns the automatic ice maker system on
and off. When the ice maker is on, the word ‘ICE’ will be
illuminated in the LCD display.
ALARM FEATURE
All integrated models have an alarm feature that will make
an audible beeping sound if a door or drawer is left ajar.
An alarm will sound if the door is left ajar or a drawer is left
open. When the alarm is activated, the symbol in the
LCD display will be visible. You can turn the alarm on or
off with the ON/O key pad, or stop it with this
control once the alarm has sounded.
When your alarm is on, the symbol will be illuminated
in the LCD display on the electronic control panel. To turn
the alarm off, press the ON/O key pad one time to
make the symbol disappear from the display.
TEMPERATURE DISPLAY
The electronic control system can display temperatures in
ahrenheit (° ) or Celsius (°C).
To convert ahrenheit to Celsius, turn the unit off then
back on. Within the first minute after turning the unit on,
press and hold the ON/O key pad and the UNIT
ON/O key pad (POWER for column models) simultane-
ously for five seconds, then release. A ‘C’ will appear in
the upper right of the temperature readings on the LCD.
ollow the same procedure to convert from Celsius to
ahrenheit.
Use the COLDER and WARMER key pads to check the set
point range(s) and verify that the temperature units were
changed.
SABBATH MODE (STAR- )
Sabbath mode is available for the observance of certain
religious holidays. This mode turns off the lights, ice
maker system and door alarm and prevents them from
turning on again. Normal cooling operations will still take
place.
Drawer models are certified by Star-K to meet strict reli-
gious regulations in conjunction with specific instructions
found on www.star-k.org. Column and tall models require
the installation of a harness kit. or details about the
harness kit, contact your authorized Sub-Zero dealer.
To initiate Sabbath mode, the unit must first be turned off
with the UNIT ON/O key pad (POWER for column
models). When the unit is off, press and hold the UNIT
ON/O key pad. The unit will turn on as soon as the key
pad is pressed. The lights will turn off after holding the
UNIT ON/O key pad for about 10 seconds. This indi-
cates that the unit has entered Sabbath mode and the key
pad can be released.
Sabbath mode can be exited by pressing the UNIT
ON/O key pad once.

Integrated Use & Care 12
Storage Shelves
ADJUSTABLE SHELVES
Depending on the model, integrated column and tall
models have adjustable tempered glass shelves or wire
shelves.
To remove or adjust the glass or wire shelves, first tilt the
shelf up at the front, then lift it up and out of the tracks on
the rear wall of the unit. Refer to the illustration below.
If the door is limited to a 90° opening, you'll need to clear
the door shelves in order to remove a shelf. Lift and pivot
the end of the shelf nearest the door upward, and remove.
To replace a shelf, insert it in the tracks at the rear of the
unit with the front of the shelf raised slightly. As you push
the shelf in, lower the front of the shelf until it locks into
position.
IMPORTANT NOTE: Always be careful in handling glass
shelves to prevent breakage or scratching the interior.
STATIONARY SHELF
The stationary glass shelf of column and tall units, except
model 736TCI, should be placed on the bottom portion of
the top compartment with the beveled edge of the shelf
support facing front. When installed properly, the rear
support legs will space the shelf away from the back wall
to ensure an even flow of air through the unit.
DOOR SHELVES
The door shelves and dairy compartment of column and
tall models are adjustable within the guides of the door
liner. The two shallow door shelves of column model
IC-27R are removable, but not adjustable.
To remove door shelves or the dairy compartment, lift
straight up and out from the bottom as shown in the illus-
tration. To replace, select a desired position and slide the
door shelf or dairy compartment down into the guides.
Door shelf removal.
Shelf removal.

Integrated Use & Care 13
subzero.com
Refrigerator Storage
DELI DRAWER AND SHELF
The one-piece deli drawer and shelf assembly in models
700TR, 700TCI and 736TR is easily removed for cleaning
and repositioning. The deli drawer is convenient for
storage of small items and for keeping deli items fresh.
Refer to the illustration below
Remove this assembly in much the same way you remove
the adjustable glass shelves.
CRISPER (MODEL 736TCI)
The sealed crisper with two dividers in model 736TCI
offers convenient storage of fruits and vegetables.
To remove the crisper, first lift the glass shelf off of the
plastic side supports, then lift the crisper bin up off of the
bin cradle. Refer to the illustration below.
To replace the crisper, place the bin on top of the bin
cradle. The groove across the bottom of the bin should
align with the crossbar at the front of the cradle. Place the
glass shelf on top of the side plastic side supports.
Deli drawer and shelf. Crisper (736TCI).
STORAGE DRAWERS AND CRISPER (MODEL IC-27R)
Column model IC-27R has two storage drawers and a
high-humidity crisper. The drawer front panel is clear so
you can easily view the contents. Be sure to unload the
storage drawers and crisper before removal.
To remove a storage drawer or the crisper, pull the drawer
out until it stops. Lift the front of the drawer slightly and
pull straight forward. Refer to the illustration below.
IMPORTANT NOTE: If the door is limited to a 90° door
opening, the shallow door shelves will need to be removed
in order to remove a drawer.
To reinstall, push the drawer slides back into the refrigera-
tor. Align the drawer with the slides, then push the drawer
straight back on to the slides until it stops. Press down-
ward on the front of the drawer to engage the slides.
Storage drawer (IC-27R).

ICE CONTAINER (MODEL IC-27FI)
The automatic ice maker and ice container of column
model IC-27 I are located in the top drawer. To remove
the ice container, pull the drawer forward until it stops and
lift the ice container out.
reezer Storage
FREEZER DRAWER (MODEL IC-27FI)
Column model IC-27 I has three wire storage drawers.
The drawer front panel is clear so you can easily view the
contents. Be sure to unload the freezer drawers before
removal.
To remove a freezer drawer pull it out until it stops. Behind
the bottom two corners of the front face of the drawer are
metal tabs. Pull these tabs toward the front of the drawer
and lift and rotate the drawer up. Refer to the illustration
below.
IMPORTANT NOTE: If the door is limited to a 90° door
opening, the shallow door shelves will need to be removed
from the bottom of the door in order to remove a drawer.
To reinstall, push the drawer slides back into the freezer.
Align the drawer with the slides and push the drawer
straight back onto the slides until it stops. Press down-
ward on the front of the drawer to engage the drawer tabs
with the slides.
Integrated Use & Care 14
TAB
Freezer drawer (IC-27FI).

Integrated Use & Care 15
subzero.com
Drawer Storage
DRAWER REMOVAL
IMPORTANT NOTE: Before removing the top drawer from
a drawer unit, you must first disconnect the control cable
as shown in the illustration below.
To remove a storage drawer from your integrated tall or
drawer unit, pull it open until it stops. Raise the drawer
front and pull out as shown in the illustration.
To replace a drawer, raise the front of the drawer up and
place onto the drawer slide tracks. Engage the hook at the
rear of each slide with slots in the back of the drawer tub.
or 36" (914) units, there are tabs on each drawer that
must be positioned between the hooks. Then engage the
small white pegs at the front of each drawer slide with
holes at the front of the drawer tub. Reconnect the control
cable.
REMOVABLE CRISPER COVER
One lift-up crisper cover is standard with each tall and
drawer refrigerator unit and the drawer combination unit.
The clear-view window allows easy access and visibility of
all vegetables stored in the drawer.
You can easily remove this cover for cleaning with soap
and water, or move it to another drawer by lifting the front
edge up and pulling out from the front. Refer to the illus-
tration below.
IMPORTANT NOTE: or model 700BC(I), drawer combina-
tion unit, the removable crisper cover can only be used in
the upper drawer.
DRAWER DIVIDER
The divider of the upper drawer is easily removed by
pulling forward and sliding the back edge away from the
back of the drawer. Reverse this procedure to insert the
divider, as shown in the illustration below.
The divider of the lower drawer is removable if there is no
ice maker, but screws have to be removed to do so. or
units with an ice maker, the lower divider is not removable.
You must first disconnect the control cable before
removing the top drawer of a drawer unit.
Control cable. Drawer removal.
Crisper cover removal. Drawer divider removal.

Integrated Use & Care 16
Ice Maker Operation
The ice maker in your integrated combination or freezer
model is fully automatic and has been factory tested. It
requires a connection to the house water supply.
To put into operation, the ice maker system must be
turned on by the ICE ON/O key pad, located on the
electronic control panel. Refer to ice maker control on
page 11.
or column models, the ice maker must be turned off at
the control panel when the ice storage container is
removed. or tall and drawer models, the ice maker shuts
off when you remove the ice storage container. When you
reinstall the container, the ice maker will resume ice
production.
IMPORTANT NOTE: The first container filled with ice
should be discarded, as with any new connection there
may be impurities in the ice from the water supply line.
Sounds
You may hear some noises in the normal operation of the
integrated unit. Surrounding acoustics like walls, floors
and cabinets may affect the sound of your unit. or
example, a gurgling or running water sound is probably
refrigerant circulating through the tubing.
During the ice maker cycle you may hear the sound of ice
dropping into the container or the solenoid valve operating
while refilling the ice maker with water. During the freezer
defrost you may hear crackling and/or sizzling as the heat
from the defrost element clears the frost from the freezer
coil and water runs into the water pan.
While the compressors are in operation, you may hear a
slight hum. During the start-up and shutdown of the
compressor, you may feel vibration for a few seconds.
Some of these noises may be enhanced when the unit's
door or drawers are open.

DRAWER LIGHTING
Each drawer compartment has a standard 25-watt
appliance bulb recessed into the top of the compartment.
Refer to the illustration below.
To replace the light bulb, pull the drawer out to its full
extension or remove the drawer completely. Refer to
drawer removal on page 15. Replace the bulb and follow
the reverse steps to reinstall the drawer.
CRISPER LIGHTING (MODEL IC-27R)
Crisper drawer lighting for model IC-27R is located behind
the upper crisper drawer and mounted to the back wall of
the refrigerator. To remove the light shield, first remove the
crisper drawer. Next, remove the upper crisper shelf. Then
place both hands under the bottom right and left sides of
the light shield and push upward. Refer to the illustration
below.
Integrated Use & Care 17
subzero.com
Lighting Information
CABINET LIGHTING
Cabinet lighting for integrated column and tall models use
standard 40-watt appliance bulbs.
To replace the light bulbs, you must first remove the light
shield. Place your hands under the light shield and release
the two clips on the back, then lift up and slide back
slowly until the key slots on the side of the light shield
drop past the mounting studs in the side walls. Remove
the light shield. The bulbs are now accessible. Replace the
bulbs and follow the reverse steps to reposition the light
shield. Refer to the illustrations below.
Shut off power to the unit at the circuit breaker before
replacing light bulbs. Wear protective gloves when
handling bulbs.
LOCKING CLIPLIGHT
SHIELD
Cabinet lighting (column
model).
Cabinet lighting (tall model).
LOCKING CLIPLIGHT
SHIELD
RECESSED BULB
Drawer lighting. Light shield removal (IC-27R).

Integrated Use & Care 18
Cleaning
INTERIOR CLEANING
It is necessary to keep your integrated unit clean to ensure
smooth operation and keep food safe. Wipe up any spills
immediately.
To clean interior surfaces and removable parts, wash with
a mild solution of soap and lukewarm water with a little
baking soda. Do not use vinegar or alcohol-based
cleaners. Rinse and dry thoroughly. Avoid getting water on
the lights and control panel. Do not use abrasive cleaners,
as these may scratch interior surfaces.
Do not use hot water to clean glass shelves until they
have come to room temperature. Extreme temperature
may cause the glass to break.
Do not use a metallic or highly abrasive cleaner or
cloth, as this will scratch the stainless steel finish.
STAINLESS STEEL EXTERIOR
To clean the exterior of a stainless steel model, use a soft,
nonabrasive stainless steel cleaner like Signature polish
and apply with a soft lint-free cloth.
Signature polish is available from Signature Limited
Laboratory, P. O. Box 13436, Dayton, Ohio 45413, or call
877-376-5474.
To bring out the natural luster of the stainless steel, lightly
wipe the surface with a water-dampened microfiber cloth
followed by a dry polishing chamois. All work should
follow the grain direction of the finish. Better results are
obtained by keeping the cloth in continuous contact with
the stainless steel.

Cleaning
CONDENSER CLEANING
or all integrated models, the condenser is located at the
bottom of the unit, behind the kickplate/grille. To clean the
condenser area, remove the kickplate/grille by removing
the screws holding it in place. The condenser is now
accessible for cleaning. Using a soft bristle brush, vacuum
to remove dust and lint from the condenser. Refer to the
illustration below.
IMPORTANT NOTE: To ensure efficient performance of
your integrated unit, the condenser must be cleaned every
three to six months under normal use. If you have pets, it
may be necessary to clean the condenser more often.
Integrated Use & Care 19
subzero.com
Failure to clean the condenser could result in tempera-
ture loss or mechanical failure or damage.
CONDENSER
Location of condenser.
Vacation Time
or extended vacations, shut off power to the unit by
pressing the UNIT ON/O key pad (POWER for column
models). Empty all contents and block the door and
drawers open slightly. A one-inch space will let fresh air in
to keep the interior dry.
IMPORTANT NOTE: Moisture accumulates in a unit that
has been shut off as it warms to room temperature, even if
it has only been in service temporarily and later shut off.
Blocking the door and drawers open slightly will allow the
moisture to escape.
or short vacations, remove all perishable items. Shut off
the ice maker by pressing the ICE MAKER key pad and
empty the ice container. It is not necessary to change the
control settings.
If your religious observances require turning off the lights
and ice maker, see Sabbath mode on page 10.
Moisture accumulation can damage interior metal
components.
Before cleaning the condenser, shut off power to the
unit at the control panel. Wear gloves to avoid injury
from sharp condenser fins.

Integrated Use & Care 20
90° door stop.
When the door is open to 105°, the door panel,
depending on its thickness, may strike the face frame
of the unit causing serious damage.
The door swing may cause severe finger pinching or
damage to the unit. Watch that fingers are not placed
in the door opening on the hinge side when the door is
open.
90° Door Stop
Integrated column and tall models are equipped with a
built-in 90° door stop. You can easily actuate the stop by
using a blade-type screwdriver and advancing the cam in
both the top and bottom door hinges.
You must actuate both stops at 90° if you want to safely
use the door. You can go to the maximum 105° opening by
using the screwdriver and advancing the cam to the next
stop.