Sub-Zero INTEGRATED REFRIGERATION User manual

INTEGRATED REFRIGERATION
USE & CARE GUIDE

2 | English subzero.com | 3
INTEGRATED REFRIGERATION
Customer Care
The model and serial number are listed on the product
rating plate. Refer to page 3 for rating plate location. For
warranty purposes, you will also need the date of installation
and name of your authorized Sub-Zero dealer. Record this
information below for future reference.
SERVICE INFORMATION
Model Number
Serial Number
Date of Installation
Certied Service Name
Certied Service Number
Authorized Dealer
Dealer Number
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
Contents
3Integrated Features
3Interactive Controls
4Storage
6Operation
7Care Recommendations
7Troubleshooting
8Sub-Zero Warranty

subzero.com | 3
Integrated Features
FEATURE PG
1Product Rating Plate 2
2Interactive Control Panel 3
3Freshness Cards 4
4Door Shelves 4
5Dairy Compartment 4
6Glass Shelves 4
7Refrigerator Drawers 4
8Ice Container 5
9Storage Drawers 5
10 Air Purication System 6
11 Automatic Ice Maker 6
12 Water Dispenser (dispenser models) 6
13 Condenser (behind grille) 7
INTEGRATED FEATURES
Column all refrigerator.
6
3
12
7
10
Tall combination.
2
1
5
4
Drawer all refrigerator.
13
6
3
1
10
2
9
5
4
13
8
11
7
13
9
1
12
10
2
Interactive Control Panel
For initial start up, touch and hold on the control panel
for 2 seconds.
Temperature can be adjusted in one-degree increments on
the home screen. Combination units have separate tem-
perature controls for refrigerator and freezer. Temperatures
are preset at 3°C and -18°C. To change temperature, touch
the temperature being adjusted, then press ‘+’ or ‘-’ until
desired temperature is displayed. Refer to the illustration
below.
Once temperature has been adjusted, additional features
can be activated or deactivated from the options screen.
Touch to view the options screen. Refer to the illustration
below.
OPTIONS SCREEN PG
Touch to activate or deactivate ice maker system
and max ice feature.
6
Touch to activate or deactivate door/drawer alarm. 3
Touch to activate or deactivate water dispenser. 6
Touch to activate or deactivate air purication
system.
6
Touch to view settings screen. 3
SETTINGS SCREEN
Touch to view model information.
Touch to select temperature unit, Fahrenheit or Celsius.
Touch to adjust control panel brightness and contrast.
Touch to adjust door/drawer alarm volume and pitch.
Touch to adjust door/drawer alarm duration.
Touch to enter Sabbath mode.
Touch to view troubleshooting and service information.
Touch to set clock.
Touch to select smart home options.
Touch to select language options.
Touch to adjust soft on lighting.
INTERACTIVE CONTROLS
Home screen.
Options screen.

4 | English subzero.com | 5
GLASS SHELVES
To remove or adjust a glass shelf, tilt up, then lift up and out.
To reposition, insert shelf in the tracks along the back wall,
then lower the front until it locks into position. Refer to the
illustration below.
The stationary glass shelf at the bottom of the compartment
should be placed with beveled edge facing front. Rear sup-
port legs space the shelf away from the back wall to ensure
proper air ow through the unit.
IMPORTANT NOTE: Use care when handling glass shelves to
prevent breakage or scratching the interior.
CAUTION
Glass shelves should warm to room temperature before
immersing in warm water.
REFRIGERATOR DRAWERS
To remove a refrigerator drawer, pull open until the drawer
stops. Lift the front of the drawer slightly and pull straight
out. To reinstall, pull drawer carrier out and align the bottom
of the drawer with the carrier. Refer to the illustration below.
Dividers in refrigerator drawers can be removed by pulling
straight up. To replace, align tabs on the divider with
notches in the drawer and push down.
Refrigerator drawer removal.
Refrigerator drawer removal.
Glass shelf removal.
Refrigerator Storage
DOOR SHELVES
To remove a door shelf or the dairy compartment, lift from
the bottom and slide out. To reinstall, place in the desired
position and slide the shelf down onto the guides. Refer to
the illustration below.
IMPORTANT NOTE: If door opening is limited to 90°, door
shelves may need to be removed before removing a storage
drawer or glass shelf.
Keeping Food At Its Best
This Sub-Zero features a unique dual refrigeration system to
keep food fresher longer.
With the Sub-Zero dual refrigeration system, individual
refrigerator and freezer systems have been designed to
maintain accurate, consistent temperatures and proper
humidity levels for longer food life expectancy. Dual refrig-
eration eliminates transfer of fresh food odors to frozen food
and ice and does not freeze the moisture out of the air in the
fresh food section.
For handy tips and information on how to maximize
food freshness, refer to the freshness cards stored in the
refrigerator.
STORAGE
Door shelf removal.

subzero.com | 5
Freezer Storage
FREEZER BASKETS
To remove, pull forward until basket stops. Pull the two
plastic tabs located behind the bottom two corners of the
basket forward, then lift up and out. Refer to the illustration
below. To reinstall, push drawer slides in. Align the basket
with slides and push back until it stops. Press down on the
front of the basket to engage slides. Refer to the illustration
below.
If door opening is limited to 90°, the top basket must be
removed before removing the middle or lower basket.
ICE CONTAINER
Column |To remove ice container, pull freezer drawer open
until it stops and lift container out. To reinstall, pull drawer
carrier out and align the bottom of the container with the
carrier. Refer to the illustration below.
Tall and drawer |To remove ice container, pull freezer
drawer open until it stops and lift container out. To reinstall,
place in the drawer with tabs on the bottom of the container
aligned with slots in the drawer. Refer to the illustration
below.
The ice maker must be turned off by touching when
the ice storage container is removed. The unit is equipped
with a 3-minute delay after the ice container is removed, to
ensure cubes are not ejected before ice maker can be deac-
tivated or ice container is reinstalled.
Freezer basket removal.
Column ice container. Tall and drawer ice container.
DRAWER REMOVAL
To remove, pull open until drawer stops. Raise the drawer
front and pull out drawer. To reinstall, raise the front of
drawer and place onto the slides. Align the back of the
drawer with hooks on the slide, then align the white pegs
at the front of the slide with holes at the front of the drawer.
Refer to the illustration below.
IMPORTANT NOTE: For drawer models, the upper drawer
has a control cable that must be disconnected before
removing the drawer. Refer to the illustration below.
Storage Drawers
CRISPER COVER
The crisper cover in the upper storage drawer can be slid
closed or left open.
To remove, pull the upper drawer all the way out, raise the
front edge of the crisper cover and pull it forward out of the
drawer. Refer to the illustration below.
DRAWER DIVIDERS
To remove or adjust a short divider, ex the long divider
slightly, then pull upward. Refer to the illustration below.
To remove a long divider, the short dividers must be
removed. Pull divider up until it stops, rotate counterclock-
wise, then pull upward. To reinstall, align grooves with
drawer tabs, rotate clockwise, then slide down.
Crisper cover. Drawer dividers.
Drawer removal. Control cable (drawers).
STORAGE

6 | English subzero.com | 7
Water Dispenser
The water dispenser is located inside the refrigerator on
the left wall. Press a glass against the dispenser to activate
water ow. Water ow will stop when the glass is pulled
away. Refer to the illustration below.
The chilled water reservoir tank holds approximately 1.2 L
of ltered water. It may take several hours to chill the water
to refrigerator temperature during the original ll and after a
large amount of water is dispensed.
To ll the tank, press a glass against the dispenser until
water begins to ow. A safety feature was incorporated into
the dispenser to limit continuous water ow to 60 seconds.
If water does not dispense within 60 seconds, remove the
glass, then reapply to the dispenser until water begins to
ow. Once the tank is full, discard the rst few glasses
of water. It may contain impurities from new plumbing
connections.
Ice Maker Operation
To initiate ice production, touch the indicator on the
options screen. A single highlighted cube indicates the ice
maker is active. Three highlighted cubes indicate the max
ice feature is active. Max ice increases ice production up to
30% for a 24-hour period. During that period, some com-
ponents may run at a higher speed resulting in a unique
audible tone. This is typical and will revert back after 24
hours or when the ice container is full. To deactivate the ice
maker, touch until no cubes are highlighted. After initial
start-up, discard the rst few batches of ice. The ice may
contain impurities from new plumbing connections.
If ice is not used regularly it may fuse together. To avoid,
discard ice and allow ice maker to replenish.
The ice maker must be turned off by touching when the
ice storage container is removed. The unit is equipped with
a 3-minute delay after the ice container has been removed,
to ensure cubes are not ejected before the ice maker can be
deactivated or ice container is reinstalled.
Sabbath
This appliance is certied by Star-K to meet strict religious
regulations in conjunction with specic instructions found
on www.star-k.org.
For Sabbath mode, from the settings screen, touch and
follow instructions on the control panel.
WATER DISPENSER
Water dispenser.
OPERATION
AIR PURIFICATION CARTRIDGE REPLACEMENT
1To access the air purication cartridge, grasp the outside
cover from the bottom and rotate upward (top and rotate
downward for drawers). Refer to the illustrations below.
2Grasp the black cover from the top and rotate down-
ward. The cartridge will pop out and can be removed.
3Remove the new cartridge from packaging and insert
with connector pointing downward.
4Once in position, close the black cover. Then rotate the
outside cover downward (upward for drawers).
5Once the cartridge has been replaced, follow instructions
on the control panel. The cartridge life cycle will reset for
approximately one year.
Air Purication System
The advanced air purication system of Sub-Zero integrated
models reduces bacteria, odors and ethylene gas, which
causes premature ripening in fruits and vegetables. If your
unit is equipped with an air purication system, the cartridge
has been factory installed and is located on the back wall of
the refrigerator (back of upper drawer for drawer models).
To initiate air purication, touch on the options screen.
The cartridge will last approximately one year. ’Change Air
Purier’ will appear on the control panel when the cartridge
needs to be replaced. Touch ’Snooze’ to delay reminder for
24 hours or until cartridge can be replaced.
AIR PURIFIER LAMP
CONTAINS MERCURY
Manage in accordance with disposal laws.
In the U.S. visit earth911.com or call 800-222-7820.
Air purication cartridge
(column and tall).
Air purication cartridge
(drawers).

subzero.com | 7
CARE RECOMMENDATIONS
Cleaning
INTERIOR CLEANING
To clean interior surfaces and all removable parts, wash with
a mild solution of soap, water and baking soda. Rinse and
dry thoroughly. Avoid getting water on lights and control
panel.
CAUTION
Do not use vinegar, rubbing alcohol or other alcohol-
based cleaners on any interior surface.
STAINLESS STEEL EXTERIOR
Use a nonabrasive stainless steel cleaner and apply with a
soft lint-free cloth. To bring out the natural luster, lightly wipe
surface with a water-dampened microber cloth followed by
a dry polishing chamois. Always follow the grain of stainless
steel.
CONDENSER CLEANING
CAUTION
Before cleaning the condenser, turn power off at the
control panel. Wear gloves to avoid injury from sharp
condenser ns.
The condenser is located behind the grille. Remove the
kickplate by extracting the two mounting screws. Refer to
the illustration below. Use a soft bristle brush and vacuum
to remove dust and lint from the condenser. Clean the con-
denser every three to six months.
IMPORTANT NOTE: To avoid damaging condenser ns,
vacuum in the direction of the ns.
CAUTION
Failure to clean the condenser could result in tempera-
ture loss, mechanical failure or damage.
VACATIONS
For extended vacations, turn power off at the control panel.
Empty the unit and block doors open slightly to let fresh air
in and keep interior dry.
CONDENSER
SCREW
Condenser location.
TROUBLESHOOTING
High temperatures, unit runs excessively or unit giving off
too much heat.
•Verify condenser is clean.
•Verify door/drawer is closing properly.
•Verify door/drawer has not been left ajar.
•Increased ambient temperatures may cause compres-
sors to run longer.
•If temperature display shows 3° and -18°, but is not
cooling, unit may be in showroom mode. Contact
your authorized Sub-Zero dealer.
No water from dispenser.
•Wait one hour, then try dispenser again. Contact
contact your authorized Sub-Zero dealer if unresolved.
Troubleshooting
UNIT OPERATION
No lights or cooling.
•Verify power is on.
•Verify electrical power to unit and home circuit breaker
is on.
No lights in refrigerator or freezer.
•Door/drawer may have been left ajar which has disabled
lights to eliminate excess heat. If lights are out, close
door/drawer for one hour. If lights are still out, contact
Sub-Zero factory certied service.
•LED interior lighting must be replaced by Sub-Zero
factory certied service.
Frost, condensation or ice build up inside unit.
•Verify condenser is clean.
•Verify door/drawer is closing properly.
•Verify door/drawer has not been left ajar.
•Verify door/drawer gasket does not have rips or tears. If
it does, contact Sub-Zero factory certied service.
•If icing is heavy, turn unit off and use a hair dryer to melt
ice. Hair dryer should be set on low and kept moving
at all times. Once ice has melted, wipe up water with a
cloth or paper towel.

8 | English
Troubleshooting
ICE PRODUCTION
No ice.
•Verify ice cube indicator appears in control panel display.
•Verify ice maker has been on for at least 24 hours.
•Verify freezer temperature near -18°C.
•Verify ice container is properly installed.
•Verify ice maker arm in down position.
•Verify water is being supplied to unit.
Blue or green ice.
•Possible copper supply line corrosion. Contact plumber
to clean or replace.
Black ecks in cubes.
•Stop use and contact Sub-Zero factory certied service.
Bad taste.
•Defrost freezer and clean with soap and water.
•Place coffee grounds or charcoal briquettes in freezer to
absorb odor.
Hollow cubes.
•Clean condenser. Contact Sub-Zero factory certied
service if unresolved.
ODOR
•Unit should be cleaned before using for the rst time.
This will clear any odors that may have been trapped
during shipping.
•Replace air purication cartridge.
•Clean unit and shelving thoroughly.
•Uncovered food could create odor which may require
cleaning.
SERVICE
•Maintain the quality built into your product by contacting
Sub-Zero factory certied service.
•When contacting service, you will need the model and
serial number of your unit. Both numbers are listed on
the product rating plate. Refer to page 3 for rating plate
location.
•For warranty purposes, you will also need the date
of installation and name of your authorized Sub-Zero
dealer. This information should be recorded on page 2.
Sub-Zero Products Limited Warranty
INTERNATIONAL PRODUCTS
FOR RESIDENTIAL USE ONLY
FULL TWO YEAR WARRANTY
For two years from the date of original installation, your Sub-Zero product warranty covers all
parts and labor to repair or replace, under normal residential use, any part of the product that
proves to be defective in materials or workmanship. All service provided by Sub-Zero under
the above warranty must be performed by Sub-Zero factory certied service, unless otherwise
specied by Sub-Zero, Inc. Service will be provided during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For ve years from the date of original installation, your Sub-Zero product warranty covers all
parts and labor to repair or replace, under normal residential use, the compressor, condenser,
evaporator, drier and all connecting tubing that prove to be defective in materials or work-
manship. All service provided by Sub-Zero under the above warranty must be performed by
Sub-Zero factory certied service, unless otherwise specied by Sub-Zero, Inc. Service will be
provided during normal business hours.
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trade-
marks and service marks of Sub-Zero, Inc. Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf
Appliance, Inc. (collectively, the “Company Marks.”) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
TROUBLESHOOTING

SUB-ZERO, INC.
P. O. BOX 44848
MADISON, WI 53744 USA
WWW.SUBZERO.COM
7025872 REV-A 3/2013