Sunbeam GrillMaster ST6501EPB User manual

PRODUCTS INC.
4101 Howard Bush Dr.
Neosho, Mo. 64850
INTERNET SITE:
www.bbqhq.com
ENGINEERING CODE
SD113023
SERIES
650
MODEL
S T 6 5 0 1 E P B
11412156A 00/11 (rev. 020801)
LOOK INSIDE FOR:
EASY ASSEMBLY INSTRUCTIONS
IMPORTANT WARRANTY INFORMATION
SAFETY AND MAINTENANCE TIPS
NOTE:
HARDWARE SHOWN ACTUAL SIZE
IN MANUAL.
FOR YOUR CONVENIENCE,EXTRA
HARDWARE MAY BE INCLUDED.CYLINDER
NOT
INCLUDED
WARNING:
THE EDGES OF SHEET METAL PARTS CAN
CAUSE INJURY IF NOT HANDLED WITH CARE.
USE EXTREME CAUTION!
IMPORTANT!
TO ENSURE PROPER GAS FLOW,BURNER
CONTROL VALVES MUST BE “OFF” BEFORE
OPENING THE GAS CYLINDER VALVE.
ASSEMBLER/INSTALLER:
LEAVE THESE INSTRUCTIONS WITH THE
CONSUMER.
CONSUMER/USER:
READ ALL THESE INSTRUCTIONS AND
KEEP THEM IN A SAFE PLACE FOR
FUTURE REFERENCE.

(Pg. 2) 1141-2156A
CAUTION:
PINCH POINTS!
USE EXTREME
CAUTION!
FRONT
BACK
WARNING:
BEFORE SETTING THE GRILL UPRIGHT,
UNFOLD THE LEGS AND SECURE WITH SIX
SCREWS AS SHOWN IN STEPS 1AND 2.
WARNING:
Combustion by-products produced when using
this product contains chemicals known to the
State of California to cause cancer, birth defects,
or other reproductive harm.
WRONG
CORRECT
REMOVE BOTH LEG CLIPS AND
THROW AWAY.
FOR SHIPPING USE ONLY.

(Pg. 3) 1141-2156A
FRONT
BACK
BACK
JR
JR
3 QTY.
JR
JR
1
JR
JR

(Pg. 4) 1141-2156A
FRONT
BACK
JR
3 QTY
JR
JR
BACK
JR
2
JR
JR

(Pg. 5) 1141-2156A
3
49
49 48
48
BACK
49
48
SET THE GREASE DRIP PANS
(48) ONTO THE CASTING AND
SECURE WITH THE GREASE
PAN HANGERS (49).
48a
48a
AFTER STEP 4, WITH THE GRILL IN THE UPRIGHT POSITION
SLIDE THE GREASE PANS (48a) INTO THE GREASE PAN HANGERS.
BACK VIEW OF GRILL

(Pg. 6) 1141-2156A
LEFT END
FRONT
4
BACK
LEFT END
JR JR
9-VOLT BATTERY (30) A
B
CAUTION:
SET GRILL UPRIGHT BEFORE PROCEEDING WITH THE ASSEMBLY.
SECURE WITH SCREWS (JR).
2 QTY
TEST THE IGNITER: A SPARK SHOULD APPEAR AT ELECTRODE TIP.
IF THE SPARK DOES NOT APPEAR:
- CHECK THE WIRE CONNECTION TO THE IGNITER.
- CHECK THE WIRE CONNECTIONS TO THE MAIN BURNER AND SIDE BURNER ELECTRODES.
- CHECK PROPER ASSEMBLY OF FRESH 9-VOLT BATTERY.
MAIN BURNER
ELECTRODES
IGNITER
SIDE
BURNER
ELECTRODES
IGNITION WIRING DIAGRAM
MODULE

(Pg. 7) 1141-2156A
RIGHT END
LEFT END
2 QTY
FRONT
5
BACK
RIGHT END
RIGHT END
JR
JR
SECURE WITH SCREWS (JR).
TIGHTEN ALL EIGHT PRE-ASSEMBLED SCREWS AT THIS TIME.
A
B

RIGHT END
LEFT END
6
41
1
40
32
32
32
JR
(Pg. 8) 1141-2156A
1
LEFT
40
41
Set the SIDE BURNER GRID (41) on the side
burner base matching tabs to the slots.
NOTE: Turn side burner grid until it stops.
Before each use, check to see that the side
burner grid is secure.
A
B
C
D
2 QTY
FRONT
PLACE
STRAIGHT
SIDE TO THE
GRILL FRONT

55
VE
VE
WO
WO
(Pg. 9) 1141-2156A
RIGHT
LEFT
FRONT
7
2 QTY
2 QTY
VE
WO
LEFT
55
WO
A
B

RIGHT
LEFT
8
2 QTY
2 QTY
63
63
B
(Pg. 10) 1141-2156A
SB
SB
DZ
58
59
DZ
A
DZ
THE WINGNUTS MUST BE IN THIS POSITION
FOR THE LID TO CLOSE CORRECTLY.