Sunbeam Luna User manual

supporting sustainability
Fibre cement
February 2023 | Version 1.0 | This is the English translation of the original Dutch installation manual
Sunbeam Luna
Installation manual
EN

Components
E
A
B
C
D
F
HGG
A Corrugated sheet adapter
B Mid clamp
C End clamp
D Self-drilling screw
E LunaLiner
F Mounting profile
G Cable clip
H Coupling
General
Description of the user
This document is intended for the installer. Sunbeam Luna should only be installed by a trained installer who has fully read and understood the contents of this
manual.
Intended use and reasonably foreseeable misuse
This type of Sunbeam Luna is suitable for installation on all pitched roofs featuring fibre cement and bitumen corrugated sheets. Sunbeam Luna must only be
used according to the instructions in this document. Sunbeam Luna must only be used with the original accessories and components supplied by the supplier.
Any other use is considered improper use and may lead to injury, damage to the system and void the warranty.
Symbols used
Symbol Meaning
WARNING
This symbol indicates a hazardous situation which, if not avoided, could result in serious injury or death.
NOTICE
This symbol indicates situations not related to personal injury.
COMMENT
This symbol indicates useful additional information.
Safety equipment
Always wear personal safety equipment and fall protection while installing Sunbeam Luna.
Safety instructions
WARNING
• Always follow the national safety regulations in the country of installation.
• Always use fall protection while installing the system.
• Preferably carry out system installation with at least two trained
installers.
• Always ensure that the roof is free of obstacles and clean during
installation of the system.
• Do not install the system in high winds or when the roof is wet.
• Always ensure that the AWP or ladder is on a firm and stable surface.
• Some roofs are not strong enough to support the system. Always check
the condition and strength of the roof before installing the system.
• Always wear personal protective equipment while installing the system.
• Always use the configuration plan derived from the Sunbeam Calculator
software during installation.
NOTICE
• Use only original parts or fittings recommended and sold by Sunbeam.
• Never walk over the system or solar panels.

Preparation
Recommended tools
Electric screwdriver Socket bit 5/16" or 8 mm
Socket bit 3/8" or 10 mm Chalk line reel Chalk Tape measure
Marking the installation area
L½
L¼
L½ + 10 mm
W
L
1. Using a tension line or chalk line, mark the outer contours of the field.
2. Mark the positions of the panel clamps. Consult the panel installation manual for this.
When using the LunaLiner, the spacing is 10 mm.
COMMENT
The mounting profiles protrude by 5 cm.
Laying method
This user manual shows the panels being placed using the bottom-to-top method.
If roofs have a steeper slope, it is recommended to place the panels using the top-to-bottom method.
1
2
3
41
2
4
3
Bottom-to-top method Top-to-bottom method

Fibre Cement
system installation
Installing the mounting profiles
1. Slightly loosen the screw that is being used to assemble the roof
sheet.
2. Slide the indentation in the sheet adapter under the screw.
3. Tighten the screw.
4. Repeat steps 1 to 3 to install the other sheet adapters.
COMMENT
Make sure that the profile is supported
by an adapter on each purlin. The maximum distance between two
adapters is 150 cm.
5. Position the profile against the adapters. Make sure that the
profile does not protrude from the adapter by more than 30 cm.
COMMENT
• Ensure that the top side of the profiles is in the same section. Do
this using the configuration possibilities of the sheet adapter.
• Make sure that the profile always protrudes from under the
panel by 5 cm.
3-5 Nm
5/16”
6. Use the self-drilling screw to tighten the mounting profile in place.
7. Repeat steps 5 and 6 to install the other mounting profiles.
COMMENT
Make sure that the teeth of the profile
engage with the adapter.
Extending mounting profiles (optional)
COMMENT
In some cases, the field may be larger
than the mounting profile. This means the mounting profile must be
extended.
1. Slide the coupling into the mounting profile.
2. Slide the other mounting profile over the coupling. Slide the
mounting profiles completely against each other.
3. Use a self-drilling screw in both mounting profiles to tighten the
coupling in place.
If the field is higher than 11 metres, a dilatation (partition) must be
implemented.
1. Place the coupling in the mounting profile.
2. Use a self-drilling screw to tighten one side of the coupling in
place.
3. Slide the other mounting profile over the coupling. Maintain a
distance of 2 cm.
4. Place the panels at a distance of minimum 10 cm from each
other. Fasten both ends in place using an end clamp. Make sure
that each end clamp is fastened to its own profile.
COMMENT
Do not place any panels over the
dilatation.
Preparing to place the panels
Click!
1. Place a cable clip at each desired position.
2. Place the return cable of the solar power system into in the cable
clips.

2
1
3. Place an end clamp into the end of each mounting profile, near
the marked outer contours of the field.
COMMENT
All clamps in the Luna system are
inserted clockwise into the mounting profile and removed counter-
clockwise.
Placing the panels
5-9 Nm
3/8”
Click!
1. Position the panel against the two end clamps at the corner of
the field.
2. Place the panel cable in the cable clip and push the cable clip to
close it.
3. Lower the panel. Align the panel with the field contour.
4. Tighten the screws of the two end clamps.
5. Place the LunaLiner on the first panel.
6. Lower the next panel and slide the panel against the LunaLiner to
set the spacing.
Click!
5-9 Nm
3/8”
7. Position the panel against the next two end clamps.
8. Connect the panel cables to the previous panel. Place the panel
cable in the cable clip and push the cable clip to close it.
9. Tighten the screws of the two end clamps.
10. Place the LunaLiner on the recently placed panel.
11. Repeat steps 6 to 10 to place the first row of solar panels.
2
1
12. Place a mid clamp in the mounting profiles, and slide the mid
clamps against the first row of panels.
5-9 Nm
3/8”
Click!
13. Position the next panel against the two mid clamps.
14. Connect the panel cable to the panel cable of the previous row.
Place the panel cable in the cable clip and push the cable clip to
close it.
15. Lower the panel. Align the panel with the field contour.
16. Tighten the screws of the two mid clamps.
17. Align the next panel with the LunaLiner and repeat steps 12 to 17
in order to place the remaining panels.
2
1
5-9 Nm
3/8”
18. Place an end clamp into the end of each mounting profile, and
slide the end clamps against the last row of installed panels.
Tighten the screws of the end clamps.

6
February 2023 | Version 1.0
This is the English translation of the original Dutch installation manual
www.sunbeam.solar/en
Sunbeam BV
Kwikstaartlaan 18
NL-3704 GS Zeist
The Netherlands
+31 (0)30 - 43 00 333
[email protected]
Sunbeam Luna
Installation manual
EN
'Sunbeam' is a registered trademark.
The Sunbeam designs are protected by several international patents.
Safety standards
The national regulations in the country of installation must be observed at all times. Make sure you are aware of the safety measures prescribed by
Sunbeam or the country of installation. If in doubt, consult your safety officer. Ensure safety or health hazards are shared with the employer, supervisor
and executive worker for their information.
General safety
• For the Netherlands: Working Conditions Decree Articles 3.16, 7.23 and 8.1 to 8.3.
• For Belgium: General Regulations for Occupational Health and Safety (ARAB).
Electrical installation
• For the Netherlands:
• NEN1010 - Chapter 7.12
• NPR 5310 - Chapter 7.12
• NEN 3140
• For Belgium: General Regulations on Electrical Installations (AREI).
Roof construction and various loads
• General:
• EN 1990
• EN 1991-1-3
• EN 1991-1-4
• For the Netherlands: NEN 7250
Sustainability
As a manufacturer and supplier of panel mounting systems, we are committed to protecting the environment. In the event of a faulty system, please
contact Sunbeam first. It may still be possible to repair the system.
Should you need to dispose the system, please dispose of the system according to the local applicable regulations. By properly disposing of the various
materials, you will help prevent potential hazards to the environment and human health. The recycling of materials also contributes to the conservation
of natural resources.
Warranty
Please refer to www.sunbeam.solar/en for warranty conditions.