Sunlight Supply Sun System Sun Winch 710180 User manual

1
Sun Winch
Grow Light Lift Kit
Congratulations on your purchase of a state of the
art wireless Sun Winch™ Grow Light Lift System!
To ensure that you get the most out of your Sun Winch™ lift kit, please
read these instructions completely and carefully BEFORE installing or
operating your system.
The Sun Winch™ lift system is designed to control a total lighting load of
not more than 50 pounds. Ensure that the light, ballast (if required) and any
hood vent hardware DOES NOT EXCEED 50 pounds.
SunWinch™ Kit Components
• 2SunWinchLiftMotors
 • 1Receiver
 • 1PowerSupply
 • 2LiftMotorCords
 • 3MountingRailSections
TooperateyourSunWinch™GrowLightLiftSystemyouwillneedto
purchaseaSunWinch™Remote.Eachremoteisdesignedtocontrol
8 Sun Winch™ lift kits. The SunWinch™ Remote is sold separately.
Scan here for
instructional video
TM
Product #710180

2
INSTALLATION
1.nInstallthe3mountingrailsectionsintoanexistingoverhead
support using the screws provided. It is the user responsibility to
ensure that the support used is adequate to bear the weight of the
lift system and grow light with associated hardware. The center
holesonthe2outsidemountsshouldbespacedtoaccommodate
the length of the grow light mounts.
2.nRemoveoneSunWinch™LiftMotorandmountitononeofthe
outsiderails.EnsurethepinintheLiftMotormountalignswiththe
center hole in the rail.
3.nRemovethesecondSunWinch™LiftMotorandmountitonthe
otheroutsiderail.EnsurethepinintheLiftMotormountalignswith
the center hole in the rail.
4.nRemovetheReceivermoduleandmountitonthecenterrailsection.
5.nAttachoneend ofaLiftMotor cord totheReceivermodule.
AttachtheotherendtotheLiftMotor.
6.nAttachthesecondLiftMotorcordasdescribedabove.
7.nAttachoneendofthepowersupplytotheReceivermodule.Plug
theotherendofthepowersupplyintoanappropriate120Vsingle
phase electrical outlet.
The system is now ready to operate. Each Sun Winch™Liftreceiveris
pre-assignedtostation#1.EachSunWinch™LiftSystemRemote
is designed to independently control 8 different grow light setups.
WARNING: If you wish to control two grow light setups independently,
YOU MUST assign each receiver a separate station number.
Receiver shown.
Each receiver can be assigned
a single station number from 1 to 8.

3
OPERATION
To lift your grow light to the desired height, press the station button
once and then a direction button. HOLD DOWN the direction button
untilthedesiredheightisreached.Releasethedirectionbutton.
PROGRAM STATION NUMBER
YourSunWinch™Liftreceiverispre-programmedtoSTATION1.
To change the station number of a receiver, read the following instructions.
Remove the cover on the receiver by removing the four small
screws. Decide what number you wish to use and remove the jumpers
on the station ID DIP switches on the receiver board. See matrix
below for proper position of the jumpers.
Dip switches with jumpers
Uncovered dip switch
Station #8 configuration shown.
Dip switches identified by numbers on right.
Dip
Switch#
Station
#1
Station
#2
Station
#3
Station
#4
Station
#5
Station
#6
Station
#7
Station
#8
1••••
2• • • •
4• • • •
8•••••••
= Dip switch with jumper Blank = Uncovered dip switch
•

4
FCC Caution:
The manufacturer is not responsible for radio interference caused by unauthorized modications
to this equipment. Such modications could void the user’s authority to operate this equipment.
FCC/47CFR15.21
Class B digital device
Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigital
device,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
oneormoreofthefollowingmeasures:
-Reorientorrelocatethereceivingantenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
-FCC/47CFR15.105
Industry Canada:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subjectto thefollowingtwo conditions:(1) thisdevicemaynotcause interference,and(2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareilnedoitpasproduiredebrouillage,et(2)l’utilisateurdel’appareildoitacceptertout
brouillageradioélectriquesubi,même silebrouillageest susceptibled’encompromettrele
fonctionnement.
Sunlight Supply,®Inc.
National Garden Wholesale®
Specializing in the wholesale of indoor horticulture,
organics & hydrogardening supplies.
Vancouver, WA • Livermore, CA • Ontario, CA • Samoa, CA
Denver, CO • Wixom, MI • York, PA • Nashville, TN • Pompano Beach, FL
www.sunlightsupply.com
©2014, Sunlight Supply, Inc.