Sunlite F5 User manual

IMPORTANT SAFETY PRECAUTIONS
• Follow all instructions in this manual and check all bolts, nuts, and
components for proper function and safety before initial use.
• Set the trainer up on a dry level surface and store away from moisture and
water.
• Before use, be sure that the trainer is in a location away from walls and
objects that may interfere with its use.
• Do not use aggressive or abrasive cleaning agents, wipe down with soap
and water after use - removing any sweat that may have fallen on the
trainer. As with other cycling equipment, the use of a pressure washer is
not recommended and may cause damage to bearings.
• Use genuine Sunlite replacement parts only - see dealer for details.
• Always check for proper function and safety before using.
• Use only as directed and intended.
• Maximum rider weight: 250lbs

# Description Replacement
Part
QTY # Desccription Replacement
Part
QTY
1 Main Frame 1 18 Wheels 70116 2
2 Front Stabilizer 70114 1 19 Nylon Nut 2
3 Rear Stabilizer 70111 1 20 Knob 70040 1
4 Seat Post 70091 1 21 Seat Post Bushing 70101 2
5 Seat Slider 7009 1 22 Pop Pin Knob 70027 4
6 Handlebar Stem 70098 1 23 Plastic Bushing - Square 2
7 Handlebar Slider 70099 1 24 Plastic Bushing - Rectangle 2
8Handlebar 70096 1 25 Square Plug 1
9Computer 70094 1 26 Computer Bracket 70093 1
10 Saddle 49498 1 27 Spring Washer 70097 4
11 L/R Crank (L/R) 70060 1/1 28 Allen Bolt 70097 4
12 L/R Pedal (L/R) 41513 1/1 29 Pulse/Computer Wire 70118 2
13a End Cap 70115 2 30 Sensor Wire 70106 1
13b Leveling End Cap 70112 2 31 Phillips Screw Cage Bolt 2
14 Carriage Bolt 4 32 Flat Washer 2
15 Arc Washer 70113 4 33 Bottle Cage 1
16 Acorn Nut 70113 4 34 Bottle 1
17 Wheel Bolt 70113 2 35 Square Plug 1
36 Extension Wire 70095 1
**Some additional small parts available - Contact your local Sunlite Dealer for details**

Assembly instructions
Step 1: Attach the Front Stabilizer (2) and Rear Stabilizer (3) to the Main Frame (1) with the Carriage Bolts
(14), Arc Washers (15) and Acorn Nuts (16). Take note that the front stablizer has wheels for moving the
unit after assembly. After attaching the stabilizer legs the rear end caps can be rotated to level the trainer if
necessary.
Step 2: Attach the pedals (12) to the crank arms (11) taking note the left pedal threads in
counterclockwise, while the right pedal threads in clockwise or toward the front of the trainer. Pedals are
marked L and R respectively. If a pedal has trouble threading - do not force it. Remove the pedal, check that
it is the correct side and try again.

Step 3: (Figure A) Attach the saddle (10) to the Saddle Slider (5) and secure, then, slide the Saddle Slider
into the seat post frame (4) securing in the desired position with the Pop Pin Knob (22). To operate the knob
simply use a twisting/pulling motion until the rail is able to move freely. The saddle slider has predrilled
holes in a variety of positions and will lock into place when positioned correctly. Finally, lock the seat post
into the seat tube at a suitable height with the Pop Pin Knob (22).
Figure A Figure B
Step 4: (Figure B) Attach the Handlebar (8) and the Computer Bracket (26) to the Handlebar Slider (7) with
Allen Bolts (28) and Spring Washers (27). Next attach the handlebar slider to the handlebar stem with the
Pop Pin Knob. Connect the Pulse Wire (30) to the Extension Wire (36) before inserting the Handlebar Stem (6)
into the main frame (1). Connect the Computer (9) to the Computer Wire (29) and mount the Computer to
the Computer Bracket (26).
Step 5: Attach the Bottle Cage (33) to the main frame
(1) with the provided Phillips Cage Bolts (31) and Flat
Washer (32).