Sunnydaze Decor WSN-WHS12 User manual
Page 1 / 4
12' WOODEN CURVED
HAMMOCK STAND
WSN-WHS12
Save these instructions for future reference.
This package includes a hammock stand only!
WHS12
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
customerservice@sunnydazedecor.com, or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
400
pounds
181.4 kg
Weight Capacity
2-PERSON
ASSEMBLY
RECOMMENDED
WARNING
CHOKING HAZARD — This item contains small parts
that can be swallowed by children. Keep children away
during assembly.
Back Nut Tap Spanner with Pivot Pin
(x2)
(not included)
Rubber Mallet
AUpright Beam 2
BBase Beam (L/R) 2
CLeg 2
DM10x130mm Bolt 4
EM10x170mm Bolt 4
F60mm Eye Bolt 2
GM10 Washer 18
HM10 Lock Nut 10
ICarabiner 4
JChain 2
Failure to read and follow instructions and safety warnings could result
in serious injury or damage to property.WARNING:
SCAN FOR
HAMMOCK SAFETY TIPS
10/2021
Beveled Edge
Counterbored
Hole
Borehole
Nylon
Insert
Identify the beveled edge on Leg (C); the
beveled edge must face inward toward
the center of the hammock stand.
IMPORTANT TIPS
When applicable, Counterbored holes
must be installed on the outside edge(s);
hardware will be recessed inside the
holes. This is especially important for
Base Beams (B).
When installing lock nuts, make sure the
raised center portion faces out; the at
surface goes on rst. Hand-tighten until
you feel resistance, which is caused by
the nylon insert.
Page 2 / 4
Carefully read all assembly steps, care instructions,
and safety information before using this product.
Save these instructions for future reference.
Assemble components on a soft, clean surface to avoid scratching/damaging the nish.
ASSEMBLY
STEP 1
B: 2 C: 2 D: 4 G: 8 H: 4
• Place two Base Beams (B) onto two
Legs (C) and loosely fasten using four
M10x130mm Bolts (D), eight Washers (G),
and four Lock Nuts (H), as shown.
Do not fully tighten hardware
until Step 2 is complete!
STEP 2
A: 2 E: 4 G: 8 H: 4
• Align the boreholes on the bottom Upright
Beam (A) with the boreholes in the base
beams.
• Loosely secure each upright beam using
two M10x170mm Bolts (E), four Washers
(G), and two Lock Nuts (H), as shown.
Fully tighten all lock nuts shown in Step 1
and Step 2 using the included Back Nut Tap
Spanners with Pivot Pins.
WHS12 10/2021
IMPORTANT: This hammock stand accommodates spreader bar hammocks that are 8' to 11'
in length from ring to ring. Rope-style hammocks are not recommended with this 12' stand.
Beveled Edge
Counterbored
Hole
Borehole
Nylon
Insert
Page 3 / 4
STEP 3
F: 2 G: 2 H: 2 I: 4 J: 2
• Install one Eye Bolt (F) on the inside of the
upright beam, and securely fasten using
one Washer (G) and Lock Nut (H).
• Repeat this step on the opposite upright
beam to secure the remaining eye bolt.
• Connect two Carabiners (I) to the outermost
links of each Chain (J). Then, clip one
carabiner onto each eye bolt.
ADJUSTING THE HAMMOCK HEIGHT (hammock not included)
Always leave some slack in the fabric when hanging your hammock.
The center of the hammock should be at a height where the user can enter and
exit the hammock safely.
Always enter and exit hammocks slowly; moving too quickly can cause the
hammock and/or stand to tip over. Excessive movements also put unnecessary
strain on the edge-glued wood, causing them to separate, which could result in
serious injury.
HANGING YOUR HAMMOCK
When adjusting hammock height, adjust both ends evenly.
The more chain links there are between the carabiners, the lower the hammock
height will be. To raise the hammock height, simply adjust the hanging hardware,
ensuring both ends are adjusted evenly.
To raise the height, unclip the chain from the carabiner on the stand, pull the
chain toward the carabiner, and clip the carabiner to an inner link on the chain.
Repeat this adjustment on the opposite side.
• SAFE USE: Follow all safety statements and warnings. Always move slowly when getting in and out of
any hammock. This stand could cause serious injury, including, but not limited to, the stand tipping over or
breaking if user(s) stand up in, swing, bounce, jump, or perform any other excessive movement while using
a hammock.
WARNING: Do not use if parts are missing,
worn, or damaged.
WARNING: Never leave a hammock hanging
on this stand while it is not in use.
WARNING: Do not allow children to use this
product without constant adult supervision.
WARNING: Always keep weight centered
over the base when using this product.
GENERAL USE & CARE
BEFORE USE
• Ensure all hardware is securely fastened.
• Only use on a flat, level surface.
• Carefully read all use, care, and safety information to ensure the stand is
used safely.
WHS12 10/2021
Page 4 / 4
WARNING!
• CHILDREN: This stand is only to be used by adults and person(s) with developed motor skills who also
understand the potential dangers if misused. Supervise children at all times. Never allow small or young children
to enter or exit a hammock without adult assistance. Never allow or encourage children to sleep or play in a
hammock. Always teach and practice safe hammock use, with and without a hammock stand.
• Frequently check the hardware to ensure it remains securely fastened; tighten loose hardware
as needed. Do not use the stand if parts are missing, broken, damaged, or worn. Don't forget that it is also
important to inspect your hammock (not included) before every use.
• Protect your investment by covering or storing this stand when not in use. Avoid long-
term exposure to precipitation and high-moisture areas. Covering the stand will protect it from damages caused
by water and sunlight. Store in a cool, dry location.
• CLEANING: Identify the direction of the woodgrain, use a soft cloth to wipe away dust and debris.
• :As the wood ages, small cracks or 'checking' can appear. Maintain the appearance of the
wood by applying a suitable wood oil or varnish regularly to help seal gaps. Clean the stand and bring it indoors,
allow it to dry thoroughly; drying may take several days. If necessary, lightly sand rough areas by hand with fine
grit sandpaper. Apply the oil or varnish as directed by the manufacturer, and only apply to wooden surfaces.
WARNING: THE ONE-YEAR WARRANTY DOES NOT COVER DAMAGES OR DEFECTS
CAUSED BY THE APPLICATION OF CHEMICAL TREATMENTS OR PROTECTIVE COATINGS.
WHS12
Mounting holes do not align Ensure components are being installed in the correct direction.
Hardware was tightened too soon. Unscrew any hardware that was fully
tightened.
The bolts are not long enough Components may be installed in the wrong direction. Carefully review
the assembly instructions and important tips.
The nut will not fully tighten onto
the bolt
This unit includes lock nuts that have a nylon insert to resist loosening
when the stand is in use. Use both back nut tap spanners with pivot
pins, one to hold the bolt head and the other to tighten the lock nut.
If you are still having trouble tightening, try a ratcheting socket wrench
(not included).
My hammock hangs too low Adjust the chains as noted in the Hanging Your Hammock section.
Ensure your hammock is suited for use with this stand.
The stand seems unstable Make sure the stand is on a at, level surface and there are no dangerous
objects, such as rocks/stones, beneath the feet.
Check that all components were installed in the correct direction.
Check that all hardware is fully and securely tightened.
The protective coating is aking o The stand may have been exposed to too much moisture and/or sunlight.
Cover or store the stand when not in use to prevent further degradation.
Wood is checked or separating The stand may have been exposed to too much moisture and/or sunlight.
Cover or store the stand when not in use to prevent further degradation.
10/2021
Table of contents
Other Sunnydaze Decor Baby & Toddler Furniture manuals
Popular Baby & Toddler Furniture manuals by other brands
RH Baby&child
RH Baby&child BELLINA CONVERSION CRIB TODDLER BED KIT instructions
Kids II
Kids II Ingenuity 60407-BS instructions
TROLL nursery
TROLL nursery SUN manual
wildkin
wildkin Step ’n Store Assembly instructions
Kids II
Kids II Comfort& Harmony Snuggle Stay Blamket quick start guide
Bebe Care
Bebe Care SORRENTO LETTO manual
