SUNPRO Retractable Awning User manual
2
We thank you for your purchase of your SunPro retractable awning. SunPro awnings will give your
family the shade and protection you need on your deck or patio. You can now look forward to months
of enjoyment and memories.
Before you begin installation, take a moment to familiarize yourself with the awning and this Owner’s
Manual. Please check to insure all of the parts listed on page 5 have been included with your awning
and that you have the correct size, frame and fabric. If you ordered an optional mounting type make
sure you have those parts. They are listed on page 5.
Installation of your Awning
When unpacking your awning, take care to protect the awning from accidental damage or soiling. Do
not drop or drag the awning on the ground.
Note: When removing the clear protective wrap from the awning, do not use a knife or box cutter
to cut plastic wrap as you could accidentally slice into your awning fabric.
Note: Your awning has been shipped to you fully assembled but it is important to follow this
instruction manual to securely fasten the mounting brackets to your home and install the awning.
Please read these instructions completely before installing your awning. Please note, you will need
a helper for installation. Left and Right references are as you are facing the house. You have been
provided with the proper fasteners for mounting to your wall surface.
For the greatest enjoyment of your lateral arm awning, please mount as high on your wall as possible,
with a recommended mounting height of 9’. Yourawning is a motorized model and your electrical cord
will allow you 16’ to reach your GFI outlet. You will find your remote included in your box.
Operating your Awning
Note: If you purchased a 20’ awning, please review the CAUTION on page 18, under “Test for Proper
Operation” before using your awning. Your awning, once installed, has the ability to be opened
partially or to its full projection to suit your deck or patio design. The pitch of your awning may be
easily adjusted, up or down, from the factory setting based upon your actual mounting height. Please
see page 20, if you would like to make this adjustment.
Note: Please follow the Care and Maintenance Guidelines on pages 21 to 24 for proper use and
inclement weather precautions.
Please retain your Owner’s Manual and Installation Instructions for future reference regarding
operation, care and maintenance, troubleshooting, customer service and warranty information.
We know that you will enjoy your SunPro retractable awning by spending more time outside on your
deck or patio.
3
Recommended Tool List
Supplies
½” & 3/8” drill bits
13”, 14”, 17” & 19” wrenches
3/8” impact driver with 17 mm impact socket
4 FT level
Caulk gun
Chalk line
Crowbar, wonder bar, or Pry bar
Hack Saw Blade
Hammer
Masonry hammer drill SDS (Hilti)
Philips head screwdriver & regular screwdriver
Power Drill
Rare earth magnet
Two ladders (Recommended 4 ft. & 6 ft. or a little giant)
Vinyl Siding Tool
Wire Cutters
Wire Strippers
Caulk
Goffo
WD-40
Mounting Hardware
4
TABLE OF CONTENTS
Welcome Page 2
Recommended Tool List Page 3
Standard Installation Parts Included / Optional Page 5
Get to Know Your Awning Size Page 6-10
Installation for Roof Mount Page 11
Bay Bracket Installation Page 12
Installation on Facia Board Covered w/aluminum Over Brick Page 13
Installation for Soffit Mount Page 14-15
Installation for Brick Mount Page 16
Installation for Siding Mount Page 17
Checking Your Awning for Proper Operation Page 18
EZ-Adjustable Pitch Page 19
Adjusting In and Out Limits of the Awning Page 20
General Care and Maintenance ofYour Awning Page 21-23
Troubleshooting Page 24-25
Accessories Page 26
Front Screen Installation Page 27
Testing the Remote Page 28
Wind Sensor Installation Page 29-30
Limit Adjustment from Fabric Stretching Page 31
Valance Bar Pin Page 32
5
Manual Crank Wand
Wall Brackets
12' = Qty 3
16' = Qty 4
20' = Qty 5
In
Out
3/8"x 4" Lag Screw
(12’: Qty 6) (16’: Qty 8) (20’: Qty10)
Standard Wall
Bracket
Remote Holder
with Hardware
Remote
3/8" Flat Washer
(12’: Qty 6) (16’: Qty 8) (20’: Qty 10)
Soffit Bracket
1 Per Standard
Bracket
STANDARD INSTALLATION PARTS INCLUDED
5/16" Flat Washer 5/16" Retaining Nut 5/16" x 2 1/2" Retaining Hex Bolt
(12’: Qty 3) (16’: Qty 4) (20’: Qty 5)
OPTIONAL INSTALLATION PARTS
Siding Plate Bracket
Color match your siding
Roof Bracket
10” = Qty 2
12’ = Qty 3
16’ = Qty 4
20’ = Qty 5
Bay Bracket
(3 sizes)
12”-17”
17”-23”
23”-29”
Quantity needed is based on
type of mounting.
5/8” Lead Anchor for Brick installations
(12’: Qty 6) (16’: Qty 8) (20’: Qty 10)
Note: Roof mount awnings will have twice the number of 3/8” flat washers and the same
number of 2 inch through bolts with matching nuts as lag screws supplied
6”
Out Button
Stop Button
In Button
Light Button
6
Awning Installation Instructions
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN
PERSONAL INJURY!
WARNING: Never attempt to repair or disassemble any part of theawning without
following replacement part procedures supplied by the manufacturer. Trying to doso
without proper instructions could result in personal injury!
Before beginning, please familiarize yourself with the components of the awning as shown in
Figure 1, and the supplied fasteners/parts shown on pages 5. Find the mounting brackets
in the package (they are separated from the awning itself). Certain brackets could have been
shipped separately.
Note: This figure shows awning with motor installed on the right side as you face thehouse.
Note: Number of brackets supplied with the awning will vary depending on awning size, see
page 5.
Before Starting
FIGURE 1
Location (e)
Location (d)
Location (c)
Location (b)
Location (a)
Image of shoulder gear loop
(EZ-Pitch Adjustment)
7
Figure 2
9”
7’6”
Tools Needed:
For any type of wall installation, you will need an assistant(s), measuring tape, two ladders, 9/16” and
17mm socket, chalk line (or string), Stud finder, Phillips screw-driver, pencil, level, electric drill and
a 1/2” or 13mm wrench. If you have a wood frame construction with wood, vinyl or aluminumsiding,
you will need in addition to the above: 1/8” and 1/4” drill bits and a Vinyl Siding tool.
If you have masonry construction or brick walls, you will need a 5/8” masonry drill bit and SDS
hammer drill.
Installation
Inspect the wall you plan to mount your awning
on, and be sure you have a clear area with nolight
fixtures, doors, windows or downspouts toobstruct
your installation. Check the wall surface for bows or
swells. If you have these conditions,
shimming the wall brackets will be required.
Mounting Height: The mounting height is defined as
one inch above the highest part of the wall bracket
from the deck/patio floor - see figure 2.
Your awning’s pitch (angle) is not pre-set at the
factory. The awning pitch (angle) can be adjusted
after installing the awning. See page 19.
Note: When making the decision on the mounting height, remember that the awning requires 9
inches of unobstructed area along the whole length of the awning to fit the mounting brackets on
your wall. see figure 3.
To assure head clearance at the front of the awning, we recommend installing the awning above 7 foot
6 inches from the deck/ patio, with an optimal mounting height of 8 foot or above.
Measure up from the deck/ patio floor on one side and make a mark at your desired mounting height
(should be at least 7’ 6"). Make a second
mark 9 inches below the first mark. The
space between these marks must be
clear of obstructions, (light fixtures, etc.)
all along the length of the wall. Using a
chalk line or a string, snap a level line on
the lower mark for the length of the
awning.
The bottom of the wall brackets will rest
on this lower line.
NOTE: For ease of mounting the awning
into the brackets,
it is very important that the line will be
straight and level.
Figure 3
9”
8’3”
8
WARNING: Proper location of the brackets is the most important aspect of the awning
installation. It is critical that you fasten all the mounting brackets to studs, joists, headersor
other major structural members.
Even a moderate wind exerts great force on the awning and mounting brackets. This is why it is
important that all the brackets will be fastened properly and securely. Proper location will also make it
easier to insert the pre-assembled awning into the supporting brackets.
WARNING: Failure to securely fasten all the brackets to the wall could result in the
collapse of the awning and cause personal injury.
NOTE: Mount brackets only in the locations recommended for your awning size.
(See pages 9 & 10 for awning sizes.
Location (a)-Betweentheleftendoftheawningandtheleftarm,onthestudnearesttotheleftend.
Location (b)-Betweenthetwoarms,onthe neareststudtotheleftarm.
Location (c)-Theneareststudtothemiddlepointoftheawning.(Size10’ -13’ only)
Location(d)-Betweenthetwoarms,ontheneareststudtotherightarm.
Location(e)-BetweentherightendoftheawningMissingtherightarm,onthestudnearesttotherightend.
NOTE: You will need to use all brackets supplied for secure mounting.
For 10 ft wide awnings, we recommend installing three brackets supplied at the locations: (a), (c)
and (e). (See Page. 9)
For 12 ft wide awnings, we recommend installing three brackets supplied at the locations: (a), (c)
and (e). (See Page. 9)
For 16 ft wide awnings, we recommend installing four brackets supplied at the locations (a), (b),
(d) and (e). (See Page. 10)
For 20 ft wide awnings, use five brackets supplied at the locations (a), (b), (c), (d), (e).
(See Page. 10)
LOCATING THE BRACKETS
On the chalk line you have marked on the house, mark the left and right ends of the awning.
Using your awning, measure the distance from the right end of the square bar to the inner and outer
edges of the right arm shoulder and record those measurements. Repeat this measurement for the
left arm shoulder. Mark on the chalk line the middle point and the points where the left and right arm
shoulders will be located.
Note: The brackets cannot be installed in the area where the arm shoulders are located.
Bracket Locations for 10’ Awning
9
Bracket Locations for 12’ Awning
(A)
(C)
(E)
Image of shoulder gear with EZ-
Adjustable Pitch.
Do not adjust more than 20 degrees
up or down. Never adjust with
awning out more than 4 feet
(A)
(C)
(E)
Image of shoulder gear with EZ-
Adjustable Pitch.
Do not adjust more than 20 degrees
up or down. Never adjust with
awning out more than 4 feet
Bracket Locations for 16’ Awning
10
Bracket Locations for 20’ Awning
(A)
(B)
(D)
(E)
(A)
(B)
(C)
(D)
(E)
Image of shoulder gear with EZ-
Adjustable Pitch.
Do not adjust more than 20 degrees
up or down. Never adjust with
awning out more than 4 feet
Image of shoulder gear with EZ-
Adjustable Pitch.
Do not adjust more than 20 degrees
up or down. Never adjust with
awning out more than 4 feet
11
Installation for Roof Mount
NOTICE: INSTALLATION OF ROOF MOUNT BRACKETS CAN ONLY BE DONE ON
ASPHALT SHINGLES. THEY CAN NOT BE INSTALLED ON TILESHINGLES!!
When installing an awning onto your roof you will need these tools in addition to the tools found
in the “installing on any wall surface” section:
•Hammer
•Caulk gun
•Roofing tar in a caulking tube
Measure the placement of the awning using a chalk line. Brackets should be place as close to the
edge of the roof line as possible and may have to hang over gutter so that you can still use the EZ-
Adjustable Pitch. Also make sure the bracket placement will
not be in the same location as the arm shoulder assembly.
How to Locate roof trusses or joists:
There a couple of different ways to locate the roof trusses
or joists. Take a hammer and gently beat on the roof about
4 to 5 feet up from the gutter. You should be able to hear
a hollow sound when not hitting the roof joist and a solid
sound when right on top of the joist.
Another method is to go into the attic and measure of the
distances of the joists and transfer the measurement to the
outside. Using a drill with a ¼ inch drill bit find the center of
the joist where the bracket is going to be located. Place the
bracket on the roof surface and predrill three holes into the
roof joist.
Remove the bracket. Using a caulk gun fill the holes
you have just drilled with roofing tar.
Replace the bracket and install the supplied lag screws
and washers into the three holes using a 17mm socket
and wrench. Be sure not to over tighten the lag screws as this may damage the wood. Install your
wall brackets onto your roof brackets using the supplied hardware. Using a caulk gun, run a bead of
roofing tar around the entire perimeter of the roof bracket. Also make sure to cover the heads of the
lag screws that you just installed with roofing tar. Finish placing the roof brackets on the roof then
install the awning into the brackets.
CAUTION: Proper location of the brackets is the MOST IMPORTANT aspect of the awning
mounting. It is critical that you fasten all of the mounting brackets to the rafters or other major
structural members.
Even a moderate wind exerts great force on the awning and mounting brackets. This is why it is most
important that all the brackets will be fastened properly and securely. Proper location will also make it
easier to insert the pre-assembled awning into the supporting brackets.
12
Bay Bracket Installation
When installing an awning over a bay window or bay with a sliding glass door you will need the
following tools in addition to those found in the “installing on any wall surface”.
•½” and 3/8” metal drill bits
•3/8”impact driver
•Exterior silicone sealant
•Depending on the construction
of the house you may also need
a SDS masonry hammer drillwith
a 5/8”drill bit and ¾ to 1 inch
shimming material.
•Torpedo level
After measuring the placement of the
awning, you will want to locate your
first two brackets on either side of the
bay. You will want to keep the
brackets close to a window or door to
ensure you are going to be installing
the lag bolts directly into the framing
of the structure.
Once you have the first two brackets
installed you may install your awning.
If you have a 20’ awning you will want
to have something in place to help
support the awning until you have the
bay brackets installed.
Drill 3/8”or ½” holes on the top and
bottom tabs of your bay bracket.
Find the stud where the bay
bracket will be hung using the
earlier referenced “how to find
a stud” section.
Drill 3/8”or ½” holes in the bay sleeve
and install the wall bracket on to the
sleeve. Place the sleeve into the bay
bracket and put it on the Awning in
line with the wall stud. Slide the bay
bracket out until it is touching the wall.
Have a helper hold a torpedo level on the square bar of the awning while gently lifting the awning upward. Be
sure the awning and the bay bracket are completely level. Once the awning is level pre-drill your holes into the
stud using the bay bracket as a guide. Fasten the bay bracket to the wall using the supplied hardware.
CAUTION: Proper location of the brackets is the MOST IMPORTANT aspect of the awning
mounting. It is critical that you fasten all of the mounting brackets to the rafters or other major
structural members.
Even a moderate wind exerts great force on the awning and mounting brackets. This is why it is most
important that all the brackets will be fastened properly and securely. Proper location will also make it
easier to insert the pre-assembled awning into the supporting brackets.
After the bay bracket is fastened to the wall make sure the sleeve is not sitting too far forward or too
far back. Once you have the sleeve set into place take the supplied self-drilling screw and drill into
the top or bottom of the bay bracket. Make sure the screw penetrates the bay bracket and thesleeve.
Take exterior silicone sealant and apply to the seam between the bay bracket and the sleeve to
ensure water will not go into the bay bracket.
Continue to install the bay brackets where other wall studs or major structural members are found in
accordance to bracket placement found on page 9 and page 10.
13
Installation on Facia Board Covered by
Aluminum over Brick
When installing on facia that is covered in Aluminum over brick you will need the following
tools in addition to the tools you already have for “installing on any wall surface” section.
•Hammer
•10 to 12”hacksaw blade
•Flat stock wonder/crow bar
After making your marks on the facia where the awning is going to be installed and the shoulder
location continue to the next steps to find your studs. Place the flat side of the wonder bar
against the brick just under the bottom lip of the facia board.
Take your hammer and gently tap the wonder bar under the facia board. Insert the hack saw
blade under the facia while gently pushing down on wonder bar under.
Slide the hack saw blade left or right of the wonder bar until it hits the side of a stud. Mark on the
facia where each side of the stud is.
Then place the hack saw blade in the center of the stud and measure up to see how high the
stud sits on the facia board. Continue finding studs where your brackets are going to be located.
If the facia board is caulked to the brick you may need to use a stud finder to locate the studs
behind the facia rather than the wonder bar.
14
Installation for Soffit Mount
Note: The following instructions are for installing to a level overhang or soffit.
Before beginning, please familiarize yourself with the components of the awning as shown onPage
9 and Page 10. Make sure you ordered soffit brackets as they are optional.
Tools Required
For installing the awning on the soffit, under the overhang, you will need an assistant,
measuring tape, two step-ladders, 9/16" socket, chalk line (or
string), Phillips screwdriver, pencil, a level, electric drill, 1/8" and 1/4" drill bits, 1/2" or 13mm wrench
and a stud finder.
Mounting Line
1. Snap a horizontal straight line on the soffit, using the chalk line, the length of the awning. When
you position your chalk line on the soffit, consider that when retracted, the awning will project 10"
from the chalk line -- see figure 13 on page 15.
Note: For ease of mounting the awning to the brackets, it is very important that the line be straight.
Locating the brackets
CAUTION:
Properlocationofthebracketsisthe
MOSTIMPORTANT
aspectoftheawning
mounting.Itiscriticalthatyoufastenallofthemountingbracketstotheraftersorothermajor
structural members.
Even a moderate wind exerts great force on the awning and mounting brackets. This is why it is most
important that all the brackets will be fastened properly and securely. Proper location will also make it
easier to insert the pre-assembled awning into the supporting brackets.
Note: Mount brackets only in the locations recommended for your size awning.
Note: You will need to use all brackets supplied for secure mounting.
For 20 ftwideawnings,use ALL 5 bracketssuppliedatlocations(a)(b)(c)(d)and(e)seePage
10
.
Location(a)–Betweentheleftendoftheawningandtheleftarm,ontherafternearesttotheleftend.
Location (b) –Between the two arms, onthe nearest rafter to theleft arm.
Location (c) –The nearest rafter to the middle point of the awning.
Location(d)--Betweenthetwoarms,onthenearestraftertotherightarm.
Location (e) –Between the right end of the awning and the right arm, on the rafter nearest to the right end.
2. On the chalk line you have marked on the soffit, mark the left and the right ends of the awning.
Using your awning, measure the distance from the right end of the square bar to the inner and outer
edges of the right arm shoulder and record those measurements. Repeat this measurement for the
left arm shoulder. Mark on the chalk line the middle point and the points where the left and right arm
shoulders will be located (points a, b and c in figure d respectively).
Note: The brackets cannot be installed in the area where the Arm Shoulders are located.
15
Installation for Soffit Mount (continued)
3. YOU MUST NOW LOCATE THE RAFTERS IN THE AREA IN WHICH EACH BRACKET MUST
BE INSTALLED AS EXPLAINED EARLIER IN “LOCATING THE BRACKETS”. Tofind the rafters,
use a stud finder. Be sure to read the stud finder instructions before usage. Mark the center of each
rafter, on which a bracket will be installed with a 7” long line.
4. Position the bracket against the soffit, centered over the vertical line, with the back of the bracket
even with the horizontal chalk line, and mark the two holes.
5. Drill 1/4” pilot holes about 3-1/2” into the rafter. This will prevent the framing from splitting while
installing the lag screws. Youmay want to cut out the vinyl in the shape of the top of the bracket to
ensure the bracket sits level on the rafter.
6. Using a 9/16” socket, install the bracket with the 3/8” x 4” long lag screws. Use the flat washer
provided under the head of the screw. Make sure not to overtighten the lag screws; doing so may split
the wood framing or weaken the screw.
7.Attach the wall brackets to the soffit brackets with the supplied hardware. Repeat for allbrackets.
WARNING: Failure to securely fasten all the
brackets to structural members of the soffit or
failure of the structural member to support an
awning could result in the collapse of the awning
and cause personal injury.
Securing the Awning into the Brackets
•Carefully remove all packaging from the awning.
•Separate the wand from the awning.
•Insert a retaining nut into each of the two
special slots in each bracket - see Fig. 14.
•With proper help, lift the awning (with fabric
Roll tube above the Square Bar) into the
brackets and position so the ends line up
with end points markedon the wall.
•Push the square bar into the brackets and
secure with one retaining bolts in each
bracket. Be sure to insert the bolt from the
bottom of the bracket up. Youmight need to
apply pressure on the square bar to permit
insertion - see page 16 figure 9. Return to
“Checking your Awning for Proper
Operation” page 16 to complete the
installation of yourawning.
Figure 13
Figure 14
16
Installation for Brick Mount
CAUTION: The masonry fasteners
recommended are NOT supplied with this
awning and ARE NOTdesigned for use in the
joint between two bricks. They are ONLY to be
installed within the main body of a brick, not
within 1/2” of an outer edge of the brick (see
figure 7). The fasteners are also not suitable for
hollow cinder-block type construction or wall
surfaces that have deteriorated. Consult a local
hardware store for fasteners that fit these types
of applications. Do not use recommended
masonry fasteners on a stucco wall.
•Remove the bracket and drill a 1/4” pilot hole using a masonry drill bit, about 3” deep for the top
hole. Make sure the bottom hole is plumbed with the top hole, then drill the bottomhole.
•Using the 5/8" masonry bit, drill both holes 4-1/2" deep. Do not allow the holes to become
tapered or oversized while drilling to this final size.
CAUTION: You must drill these holes in the two specified steps. If you do not follow these
steps, the size of the hole can become too large and the bolts will not hold properly.
•Place a flat washer under the head of the lag bolt and screw the bolt into the lead shield using a
9/16" socket - see page 25 figure 10. Repeat for another bolt. While tightening the bolts, make sure
to keep the bracket plumb (use a level if needed). Do not overtighten the bolts.
WARNING: Youmust be sure the lag bolts are tight in the shields. If not, remove them and
consult a local hardware store for fasteners that fit your application.
Repeat for all brackets.
Securing the awning into the
brackets
Carefully remove all
packaging material from the
awning.
Separate the wand from the
awning. Fig. 9 Fig. 10
Insert the retaining nut into the special groove in each bracket - see figure 10.
With the proper help, lift the awning (with fabric/roll tube above the square bar) into thebrackets
and position so the ends line up with end points marked on the wall -see fig. 8.
WARNING: NEVER INSTALL AN AWNING ON SOLIDER BRICK. Solider brick
does not allow you to securely fasten your awning. Installing your awning on solider
brick could result in personal injury.
Fig. 8
17
Installation for Siding Mount
Note: For an attractive, finished appearance on Wood Siding, you can use spacers or siding plates
underneath each bracket to make a flat surface. For Vinyl or Aluminum Siding, shimming beneath the
siding in each bracket location may provide a more solid surface for mounting - see figure 4. Siding
plates are supplied with your awning if specified at the time of sale.
Position the bracket on the wall (or on the shim), centered over the vertical line, with the bottom of
the bracket even with the lower horizontal chalk line. Using a level, plumb the bracket vertically, then
mark the top and bottom holes-- see figure 5.
Remove the bracket and drill the top hole through the siding bracket or shim (if appropriate) and
about 3-1/2” into the stud or joist. using a 1/4” drill bit. This will prevent the framing from splitting
while installing the lag screws. Make sure the bottom hole is plumbed with the top hole, then drill the
bottom hole. Using a 9/16” socket, install the bracket with the two 3/8” x 4” long lag screws. Use the
flat washer provided under the head of the screw. While tightening the lag screws, keep the bracket
plumb (use level if needed). Do not overtighten the lag screws; doing so may split the wood framing
or weaken the screw -- see figure 5.
Repeat for all brackets.
WARNING: You must securely fasten all the brackets to the studs. Some homes may require
longer lag screws. Please consult with a local handyman or contractor if appropriate.Failure
to do so could result in collapse of the awning and cause personal injury.
Figure 4 Figure 5
18
Checking Your Awning for Proper Operation
NOTE: Do not plug the power cord into the
outdoor outlet yet.
Plug the electric cord into your outdoor ground fault
receptacle.
We’ve also supplied a wall holder for the remote
transmitter - see page 5.
CAUTION: Do not permit the hand-held remote transmitter to
get wet as this can affect its proper operation. It
is recommended to install the wall holder inside the house.
WARNING: Make sure to unplug the awning before using the
crank wand.
Note: During an electrical outage, you can open or close your awning using the crank wand
supplied. Just insert the wand into the black crank loop and turn –see photo
Test for Proper Operation
Note: The open and close stop limits on the awning motor were set and tested at the factory prior to
shipment.
CAUTION: When opening the awning for the first time, it is very
important to be sure that the Open stop setting on the motor has not
been disturbed during shipment to your home. After pressing the
‘Open’ button on the remote transmitter to extend the awning, be ready
to press the middle button if the awning continues to unroll past the
point that the fabric starts to excessively sag. If this happens, press the
‘Close’ button on your remote transmitter to close the awning and refer
to page 20 reset the open limit position on the motor.
Test the operation of your awning by using the open and close buttons
on your remote control. The awning should open to its full projection
and the arms will still be bent but not locked at the elbow (this is
normal). The awning should close so that the front bar is just inside the
protective housing. If your awning fails to open to its full projection or
does not appear to open and close properly, please follow the steps on
page 20 to reset the Open/Close Stop Limits. Are you happy with the
height and level of the Front Bar? If yes, Great! Your installation is now
complete. Enjoy your new awning. If No, and you would like to change
the pitch(angle) of your awning- refer to page 19.
Note: Please refer to pages 21 to 24 for Care and Maintenance Guidelines for your awning.
19
EZ-Adjustable Pitch
One of the great features of your awning is the EZ-Adjustable Pitch that came standard
on your awning. This allows you to adjust the pitch of the awnings left or right side
individually.
To adjust the pitch, insert crank handle hook into the loop shown (do not use the black
loop as that is for emergency manual override only) and turn clockwise to raise and
counter clockwise to lower.
Caution:
•Do not adjust the slope more than 20 degreesfrom its
factory setting.
•Do not extend the awning out more than 4 feet when
adjusting the slope. After slope is adjusted, then
extend awning out to the desired projection.
•You can adjust the slope with the awning all the way out with a
second person slightly lifting the front bar to take the weight off
the arm that is being adjusted.
•If you are going to use your awning in lite rain you must use EZ-
Pitch to slope the awning to one side or the other to allow water
to drain off the awning fabric. Failure to do so could allow water
to accumulate and damage your awning and even pull off its
mounting!
WARNING: The awning is not designed to hold the weight of rainwater pooling on the fabric.
Accumulation of rainwater on the fabric could collapse the awning and cause serious injury.
20
Adjusting In and Out Limits of the Awning
•The motor on your awning is mounted on the right, as you face the house, complete Steps 2 thru 6.
•Press the Neutral/Stop button on the remote.
•From a stepladder locate the two 4mm limit Allen screws on the motor. These screws will be colored.
One will be red, and one will be white. These are thelimit screws for the IN and OPEN positions for
the motor on the awning.
Limit settings
•Toadjust the inward setting of motor, locate the Allen screw that is red and turn it counter clockwise
or towards the plus (+) sign to close the awning tighter. You must run the awning motor by using the
remote control while adjusting the limit. Fig 6
•Toadjust the outward setting of the motor, locate the Allen screw that is white and turn it clockwise
or towards the plus (+) sign to increase the projection of the awning. Be sure not to “LOCK” the arms
or allow the fabric to sag when making this adjustment. The arms should stop just before the lock
position. The fabric will also be at it tightest point.
NOTE: The fabric should be rolling over the top of the roll tube (figure 4), not underneath (figure 5).
If the fabric is rolling from the bottom of the roll tube, continue unrolling the fabric until it rolls over the
top of the roll tube. Then roll up the fabric until both lateral arms ‘lock’ and the fabric become tight.
Figure 4
Figure 5
Figure 6
Table of contents
