SUNRICH TECHNOLOGY N-480 User manual

PCIe 10G 5-Speed
Multi-Gigabit Network Card
User Manual
Ver. 2.00
All brand names and trademarks are properties of their
respective owners.

MN7000000097 Page 2
Contents:
Chapter 1: Introduction......................................................3
1.1 Product Introduction....................................................3
1.2 Features........................................................................4
1.3 Requirements...............................................................4
1.4 Package Contents.........................................................5
Chapter 2: Getting Started .................................................6
2.1 Hardware Layout.........................................................6
2.2 Hardware Installation ..................................................7
2.3 Driver Installation........................................................7
2.3.1 Installation for Windows.......................................8
2.3.2 Installation for Linux............................................9
2.4 Verifying the installation............................................10
2.4.1 Verifying for Windows........................................10
2.4.2 Verifying for Linux.............................................11

MN7000000097 Page 3
Chapter 1: Introduction
1.1 Product Introduction
This card is a Multi-Gigabit network adapter that’s runs on a high
speed PCIe x4 host bus interface.
This card hosts the Tehuti’s new 3rd generation TN4010 controller, and
optimized 10 Gigabit Ethernet MAC designed for low-power, low-cost,
single-port connectivity required by Application Servers and
Workstations. The TN4010 MAC is paired with Marvell® Alaska®
88X3310P transceiver, a low-power, high-performance 10 Gigabit
Ethernet PHY, to enable five-speed connectivity (10GBase-T,
5GBase-T 2.5GBase-T 1000Base-T, and 100Base-TX) over low-cost
standard CAT-6a Ethernet cabling, up to 100m (Cat-5e and CAT-6 are
supported compliant to Link Segment specifications). This
combination creates a new gateway to cost-conscious consumer
applications, as well as to intensive data environments.

MN7000000097 Page 4
1.2 Features
Support 5-Speed 10Gb/5Gb/2.5Gb/1Gb/100Mb auto negotiation
Runs up to 10G at 100m Cat 6A cable and 5G at 100m Cat
5e/Cat 6 cable
Backward compatibility with 1000Base-T, 100Base-T Networks
PCI Express Gen-2 x4 host bus interface
EEE (Energy Efficient Ethernet)
9K Jumbo Frames
IP, TCP, UDP checksum offloading
IEEE 802.1Q VLAN
Virtual NIC support
Reduced CPU utilization and improved throughput
1.3 Requirements
Hardware
The following system specs are recommended minimum
PCIe slot: Available 4-Lanes PCI-Express slot gen 2.0 or later
Processor: Quad Core 3.0GHz or higher
RAM: 4GB memory or higher

MN7000000097 Page 5
Software
Operating systems supported are (both 32 and 64 bits)
Windows 7
Windows 8.1
Windows 10
Windows Server 2008 R2
Windows Server 2012
Windows Server 2012 R2
Linux 2.6.32 or later
VMware ESXi 5.x/6.0
Mac OS X 10.12.6 or later
1.4 Package Contents
1 x PCIe 10G 5-Speed Multi-Gigabit Network Card
1 x Low profile bracket
1 x Driver CD
1 x User Manual

MN7000000097 Page 6
Chapter 2: Getting Started
2.1 Hardware Layout
Link/Activity Indicator:
When the LED is off, there is no link between the PCIe 10G
5-Speed Multi-Gigabit Network Card and the network
When the LED is on, a link is established, but there is no traffic
on the network
When the LED is flashing, there is traffic on the network to
which the 5-Speed Multi-Gigabit Network Card is connected

MN7000000097 Page 7
Link Speed Indicator:
When the LED is lit orange, a 10GBase-T link is established
When the LED is lit green, a 5GBase-T/2.5GBase-T/1000Base-T
link is established
When the LED is off, a 100Base-T link is established
2.2 Hardware Installation
1. Turn off the power to your computer.
2. Unplug the power cord and remove your computer’s cover.
3. Remove the slot bracket from an available PCIe slot.
4. To install the card, carefully align the card’s bus connector with
the selected PCIe slot on the motherboard. Push the board down
firmly.
5. Replace the slot bracket’s holding screw to secure the card.
6. Secure the computer cover and reconnect the power cord.
2.3 Driver Installation
The following section shows you how to install 5-Speed Multi-Gigabit
Network Card driver on different operating systems.

MN7000000097 Page 8
2.3.1 Installation for Windows
 Insert the provided CD into your disk drive. The CD-ROM
will start automatically. The following screen will show up and
please click “Install Driver”.
*Note: Actual image may vary
Note: If the install program doesn’t run automatically, please
locate and double-click on the Autorun.exe file in the CD to
launch the install program.
 Please click “PCIe 10G” to start the installation.

MN7000000097 Page 9
*Note: Actual image may vary
 Follow the instructions on screen to install the driver.
2.3.2 Installation for Linux
1. Insert the provided CD into your CD-ROM drive.
2. Extract the compressed driver source file to a certain directory by
the following command: (Please copy the driver file
“tn40xx-x.x.x.x.tgz” from the CD folder
“.\Driver\10G\TN4010\Linux” to a certain folder on hard drive)
# tar xf tn40xx-x.x.x.x.tgz
3. Now, the driver source files should be extracted under the current
directory. Executing the following command to compile the
driver:

MN7000000097 Page 10
# make
4. If the compilation is well, the tn40xx.ko will be created under the
current directory.
5. If you want to use modprobe command to mount the driver,
executing the following command to install the driver into your
kernel:
# make install
2.4 Verifying the installation
2.4.1 Verifying for Windows
1. Click on the “Device Manager” tab in the Windows Control
Panel.
Start > Control Panel > Device Manager

MN7000000097 Page 11
2. Entry “Network adapters” item, and you can read “Tehuti
Networks 10GbE Adapter” in the Device Manager.
2.4.2 Verifying for Linux
1. You can check whether the driver is loading by using following
commands:
# lsmod | grep tn40xx
# ifconfig –a
If there is a device name, ethX, shown on the monitor, the linux
driver is load. Then, you can use the following command to
activate the ethX.
# ifconfig ethX up, where X=0,1,2,…