Sunset Swings 460GN Supplement

Sunset Swings
Assembly & Operation Manual
Model 460GN
Six Person Glider
RecordSerialNumberHere
www.sunsetswings.com by Health In Motion LLC 1 June 2010

460GN Assembly and Operation Manual
READ! VERY IMPORTANT
RESIDENTIAL USE ONLY
FOR ADULTS ONLY
Caution: Make sure the swing has completely stopped
before entering or exiting the swing. Be careful as the swing
may shift while entering or exiting.
This swing is for casual relaxation swinging only.
Make sure bystanders are at least 5 feet away from the swing
while it is in motion.
Be cautious swinging while children are present as they may
stray into the path of the swing.
In freezing climates, the canopy should be removed, folded and stored in a dry place
before the first freeze or snow and until the last freeze or snow has passed. The
canopy can not support the weight of snow. Failure to remove the canopy during
periods of snow will damage the canopy.
The canopy is not designed for high winds. If high winds are expected, please
remove the canopy. Failure to follow this instruction can result in damage to the
canopy.
The swing uses a natural hardwood which might contain slight imperfections.
See the General Maintenance section for proper care of the wood.
2

Thank you for choosing Sunset Swings. Please read the contents of this manual thoroughly. The
information inside will help you in many different areas. You will need to send in your customer
registration card at the back of this manual to validate your warranty. You may
also complete your customer registration at www.sunsetswings.com.
Table of Contents
Positioning Your Swing 4
Tools Required For Assembly 4
Helpful Installation Hints 4
Exploded Swing Diagram 5, 6
Hardware and Tool Diagram_________________________________ 7
Parts and Hardware List 8
Assembly Instructions 9-24
General Maintenance Information_____________________________25
Safety Tips_______________________________________________25
Label Reference___________________________________________26
LimitedWarranty 27
Warranty Claim Procedure___________________________________27
Sunset Swings by Health In Motion LLC reserves the right to alter the specifications of this product at any time.
3

Positioning Your Swing
1. The swing is designed to be installed on a level surface.
2. There should be a minimum clearance of four feet in front and back, and two feet on each
side of your swing. It should be placed in an area where children will not stray or walk into
the path of the swing.
Tools required for assembly
1. 13, 17 and 19 mm box or ratchet wrench
2. 4, 5 and 6 mm Allen wrenches (supplied with the hardware)
Helpful installation hints
1. At least 2 people are required to assemble this swing. Some parts are large and
heavy. Use care when handling.
2. Identify all of the parts for your swing. Empty the boxes and lay out the parts for
identification using the Parts List.
3. Read all the way through the instructions completely before beginning the assembly.
4. Do not tighten hardware completely until instructed. It helps to have some adjustment
for bolt alignment while you are connecting parts. Follow the tightening sequence as
mentioned in the steps. After you have completed the assembly, recheck that all
hardware is secure and tight.
4

Exploded Diagram
5

Exploded Diagram
6

7

Parts List Hardware List
Part# Description Qty (pcs) Part# Description Qty (pcs)
1 Top Beam 2 32 M10*73 Carriage Bolt 8
2 Inside Upright 4 33 M10*67 Carriage Bolt 4
3 Corner Upright 4 34 M10*63 Carriage Bolt 8
4 Cross Beam 2 35 M10*75 Button Head Screw 2
5 Upright Bracket 4 36 M10*25 Button Head Screw 12
6 Canopy Support Tube 1 37 M10*53 Carriage Bolt 8
7 Swing Arm 4 38 M10*58 Button Head Screw 8
8 Left Seat Frame 2 39 M12*35 Button Head Screw 4
9 Right Seat Frame 2 40 M8*51 Carriage Bolt 8
10 Seat Base 2 41 M12*84 Carriage Bolt 2
11 Table Base 1 42 M10*80 Carriage Bolt 2
12 Table Post 1 43 M10*26*M6 T Nut 16
13 Table Frame 1 44 M6*15 Button Head Screw 20
14 Foot Rest stopper 1 45 M8*50 Button Head Screw 8
15 Foot Rest 2 46 M10*93 Button Head Screw 2
16 Cup Holder 4 47 M10*37*M6 T Nut 4
17 Bearing Flange 4 48 Φ6 Large Washer 20
18 Ball Bearing 12 49 Φ8 Flat Washer 16
19 Wood Seat 2 50 Φ10 Arc Washer 24
20 Seat Back 2 51 Φ10 Flat Washer 28
21 Table Wood 2 52 Φ12 Flat Washer 14
22 Arm Rest 4 53 M8 Lock Nut 8
23 End Cap (fit with 25.4*25.4*2 tube) 6 54 M10 Lock Nut 40
24 End Cap (fit with 38*38*2.5 tube) 12 55 M12 Lock Nut 6
25 End Cap (φ60) 1 56 Φ25*Φ10*2.5 Washer 8
26 Anti-Slipping pad 1 57 4# Allen Wrench 1
27 Rubber Pad 1 58 6# Allen Wrench 2
28 End Cap 4 59 8#(120*40) Allen Wrench 1
29 Bushing 4
30 Shaft 4
31 Canopy 1
8

Complete Step 1 through 3 for both sides of the swing. Only finger tighten the
hardware in Steps 1 through 3 at this time. This will make it easier to install the hardware. It
will be fully tightened later.
9

Two people are required for Step 4
Tighten all the hardware in Step 4 at this time.
10