Sunset Swings 422L Supplement

Sunset Swings
®
By Health In Motion,
LLC
Model 422L
Dual Lounge Swing
Assembly & Operation Manual
Record Serial Number Here
www.sunsetswings.com
1 MARCH 2014

Page 1
Caution:
READ! VERY IMPORTANT
FOR ADULTS ONLY
Ensure that the 422L swing is set up on a firm level surface.
Make sure the swing has completely stopped before entering or exiting the
swing. Be careful as the swing may shift while sitting down or getting up from
the swing.
Keep all body parts within the swing seat while in motion.
Make sure bystanders are at least 5 feet away from the swing while it is in
motion. Be careful placing the swing too close to a structure as severe injury
might occur if a person gets caught between the structure and the swing or
damage might occur if the swing hits the structure.
Be cautious swinging while children are present as they may stray into the path
of the swing.
Review the maintenance schedule before each use to ensure the swing is in good
working order.
This swing is for casual relaxation swinging only.
In freezing climates, the canopy should be removed, folded and stored in a dry place before the
first freeze or snow and until the last freeze or snow has passed. Failure to follow these
instructions can cause damage to the canopy or canopy rods and will void the warranty.
The canopy is not designed for high winds. If high winds are expected, please remove the canopy.
Failure to follow this instruction can cause damage to the canopy or the canopy rods and will void
the warranty.
The swing uses a natural hardwood which might contain slight imperfections.

Page 2
Thank you for choosing Sunset Swings®. Please read the contents of this manual thoroughly.
The information inside will help you in many different areas. You will need to send in your
customer registration card at the back of this manual to validate your warranty. You may also
complete your customer registration at www.sunsetswings.com.
Table of Contents
Positioning Your Swing 3
Tools Required For Assembly 3
Helpful Installation Hints 3
Exploded Swing Diagram 4
Tool and Hardware Diagram 5
Parts List 6
Assembly Instructions 7-12
Weekly Maintenance Information 13
Safety Information 14
Label Reference 15
Limited Warranty 16
Warranty Claim Procedure 16
Sunset Swings® by Health In Motion LLC reserves the right to alter the specifications of this product at any time.

Page 3
Positioning Your Swing
1. The swing is designed to be installed on a firm level surface.
2. There should be a minimum clearance of five feet in front and back, and two feet on
each side of your swing. It should be placed in an area where children will not stray
or walk into the path of the swing.
3. Be careful placing the swing too close to a structure as severe injury might occur if
someone gets caught between the structure and the swing or damage might occur if
the swing hits the structure.
Tools required for assembly
1. 10, 14, 17 and 19 mm box or ratchet wrench
2. 4, 5 and 6 mm Allen wrenches (supplied with the hardware)
Helpful installation hints
1. At least 2 people are required to assemble this swing. Some parts are
large and heavy. Use care when handling.
2. Identify all of the parts for your swing. Empty the boxes and lay out the parts for
identification using the Parts List.
3. Read all the way through the instructions completely before beginning the assembly.
4. Do not tighten hardware completely until instructed. It helps to have some adjustment
for bolt alignment while you are connecting parts. Follow the tightening sequence as
mentioned in the steps. After you have completed the assembly, recheck
that all hardware is secure and tight.

Page 4
EXPLODEDDIAGRAM

Page 5
TOOL AND HARDWAREDIAGRAM

Page 6
PARTS LIST
NO#
Item#
Description
QTY
1
GM750-101-001
Bent Leg
2
2
GM750-201-003
Curved Flange
2
3
GM750-200-001
Left Upright Assembly
1
4
GM750-200-002
Right Upright Assembly
1
5
GM780-240-001
Top Beam Assembly
1
6
GM780-320-001PZ
Adjustable Canopy Support Assembly
1
7
0116-012-003
M12 Flat Washer
M12
24
8
0116-010-003
M10 Flat Washer
M10
22
9
0110-712-003
M12 Lock Nut
M12
12
10
0110-710-003
M10 Lock Nut
M10
18
11
GM750-380-001
Wood Support Bracket
2
12
GM780-561-008
Pivot Shaft
2
13
GM780-300-001
Swing Support Arm
2
14
GM780-400-001PZ
Seat Frame
2
15
0111-212-333
M12*33 Hex Head Bolt
M12*33
8
16
GM780-400-004
Right Bent Seat Tube
2
17
GM780-400-003
Left Bent Seat Tube
2
18
GM780-400-005
Separator Mount
4
19
GM760-400-001
Wood Table
2
20
GM780-400-006
Seat Fabric
2
21
GM780-400-007
Pillow
2
22
GM750-881-001UV
Swing Foot
4
23
GM780-401-009
Seat Mount Bracket
8
24
GM780-401-001
Seat Frame Connecting Plate
2
25
GM710-400-003
Canopy
1
26
GM710-801-001
Canopy Rod
4
27
0111-410-753
M10*75 Carriage Bolt
M10*75
4
28
0116-610-003
M10 Arc Washer
M10
30
29
0110-710-003A
M10 Thick Lock Nut
M10
4
30
0113-210-903
M10*90 Button Head Bolt
M10*90
4
31
0111-410-853
M10*85 Carriage Bolt
M10*85
2
32
0111-010-053
M10*115 Hex Head Bolt
M10*115
2
33
0111-012-753
M12*75 Hex Head Bolt
M12*75
4
34
0111-010-253
M10*25 Hex Head Bolt
M10*25
8
35
0111-010-453
M10*45 Hex Head Bolt
M10*45
16
36
0113-208-357
M8*35 Button Head Bolt
M8*35
4
37
0116-202-083
Φ20*Φ8.3*2 Flat Washer
Φ20*Φ8.3*2
4
38
0116-008-003
M8 Flat Washer
M8
4
39
0110-708-003
M8 Lock Nut
M8
4
40
0111-410-083
M10*80 Carriage Bolt
M10*80
2
41
0511-606-03
6mm Allen Wrench
6#
1
42
0511-605-002
5mm Allen Wrench
5#
1
43
0511-604-01
4mm Allen Wrench
4#
1

Page 7
Two people are required for STEPS 1 through 6
STEP 1: Add 2 SWING FEET to each BENT LEG
STEPS 2 and 3: Attach the BENT LEGS to the RIGHT and LEFT UPRIGHT ASSEMBLIES
STEPS 4 and 5: Attach the TOP BEAM to the RIGHT and LEFT UPRIGHT ASSEMBLIES. Ensure that the
swing mounting flanges on the TOP BEAM are facing to the back of the unit.
STEP 6: Attach the ADJUSTABLE CANOPY SUPPORT ASSEMBLY to the TOP BEAM.
WRENCH TIGHTEN ALL HARDWARE NOW

Page 8
STEP 7: Insert the PIVOT SHAFT through the TOP BEAM flanges and through the SWING SUPPORT ARM
bearing (Repeat for both right and left sides). DO NOT tighten the TOP BEAM set screws at this time.
STEP 8: Insert the M10x115 bolt and hardware through the flanges on the TOP BEAM. Tighten the hardware
now. Repeat for both sides. Now tighten the set screws to secure the PIVOT SHAFT.
STEP 9: Assemble the SEAT FRAME ASSEMBLIES so that the adjustment handle is facing to the inside of the
unit.

Page 9
STEP 10: Assemble the SEAT FRAME MOUNTING BRACKETS onto both SEAT FRAME ASSEMBLIES
DO NOT TIGHTEN ANY HARDWARE

Page 10
STEP 11: Be sure the Velcro side of the SEAT FABRIC is facing down. Slide the SEAT FABRIC up from the
bottom of the LEFT AND RIGHT BENT SEAT TUBES so it is oriented as shown.
STEP 12: Attach the SEPARATOR MOUNT to the upper and lower threaded portions of the LEFT AND RIGHT
BENT SEAT TUBES. Tighten the bolts only until the fabric is taut.
Repeat STEPS 11 AND 12 for the other SEAT ASSEMBLY

Page 11
STEP 13: Attach the SEAT ASSEMBLY to the SEAT FRAME ASSEMBLY at the 4 middle threaded locations
on the SEAT ASSEMBLY BEND SEAT TUBES.
Repeat STEP 13 for both SEAT ASSEMBLIES
TIGHTEN ALL HARDWARE FROM STEP 10
STEP 14: Attach the PILLOW to both SEAT ASSEMBLIES by wrapping the Velcro strap around the backside
of the seat. The pillow height may be adjusted by moving adjusting the position of the Velcro strap.

Page 12
STEP 15 and 16: Attach the table WOOD SUPPORT BRACKETS to the BENT LEGS and attach the WOOD
TABLE to the WOOD SUPPORT BRACKETS. Tighten the hardware now.
STEP 17: Place the CANOPY RODS into the ADJUSTABLE CANOPY SUPPORT ASSEMBLY. They will
just sit in the tubes until the CANOPY is put on the swing.
NOTE: If the CANOPY is too cold it will not stretch enough to get it over the last CANOPY ROD. Place the
CANOPY in a warm room until it warms up enough to stretch over the last CANOPY ROD.
STEP 18: The CANOPY is a rectangular piece of fabric with pocketed corners. Begin by laying the CANOPY on
top of the CANOPY RODS. Then slide one of the pocketed corners of the CANOPY onto one of the CANOPY
RODS. Continue around the CANOPY until the last corner. Getting the last corner onto the CANOPY ROD
requires stretching the fabric by pulling the CANOPY fabric towards the end of the CANOPY ROD and slightly
down. Continue stretching the CANOPY towards the end of the CANOPY ROD until it slides into the corner
pocket of the CANOPY.

Page 13
422L Swing Weekly Maintenance
Inspect and familiarize yourself with the safety warnings and other information that is
posted on the decals located on the swing or in the owner’s manual.
Inspect all fabric areas for tears and fabric seams for loose or damaged threads. Replace
immediately if needed.
Inspect all the hardware for proper tightness, Retighten if needed.
Inspect the wood for weather cracking. The wood is a natural product and there might be
slight imperfections that are visible. During normal weathering the wood may crack
slightly due to changes in moisture. This is a natural occurrence and does not affect the
structural integrity of your swing. The wood should be treated every 3 months, or as
needed, with a wood preservative. See your local hardware retailer for suggestions for
wood preservatives. Failure to protect the wood will void its warranty.
The canopy is not designed for high winds. If high winds are expected remove the canopy.
Failure to follow these instructions can cause damage to the canopy or canopy rods and will
void the warranty.
In freezing climates the canopy should be removed, folded and stored in a dry place before
the first freeze or snow and until the last freeze or snow has passed. Failure to follow these
instructions can cause damage to the canopy or canopy rods and will void the warranty.

Page 14
Safety Information
CAUTION!
This 422L swing is designed for adult use only
Ensure that the 422L swing is set up on a firm level surface.
Make sure the 422L swing has completely stopped before entering or exiting the swing. Be
careful as the swing seat may shift while sitting down or getting up from the swing.
The foot rest should be tucked under the seat when entering or exiting the swing.
Keep all body parts within the swing seat while it is in motion.
Make sure bystanders are at least 5 feet away from the swing while it is in motion. Be
careful placing the swing too close to a structure as severe injury might occur if a person
gets caught between the structure and the swing or damage might occur if the swing hits
the structure.
Be cautious swinging while children are present as they may stray into the path of the
swing.
Review the maintenance schedule before each use to ensure the swing is in good working
order.
This swing is for casual relaxation swinging only.
Residential use only.

Page 15

Page 16
Sunset Swings
®
By Health In Motion LLC
LIMITED TEN YEAR WARRANTY
Sunset Swings® warrants this product to the original purchaser to be free from defects in workmanship and/or materials
under normal use. If, during the warranty period, a component part is defective, Sunset Swings® shall repair or replace it (at
Sunset Swings® option) within a reasonable period of time. This warranty does not cover costs of removal, transportation
or reinstallation. This warranty shall not apply if damage is caused by misuse, improper maintenance or assembly, neglect
or normal wear and tear. Starting from the original date of purchase, normal wear and tear shall be considered as the
following: All failures of the rubber, fabric and wood that occur after 2 years, all failures of bearings, bushings, hardware
or powder coated frame that occur after ten years. If the swing is located within 2000 feet of a salt water shore/waterway or
10 feet of a pool, warranties may be void. Sunset Swings® sole responsibility shall be to repair or replace the component
within the terms stated above. Sunset Swings® shall not be liable for any loss or damage of any kind including any
incidental or consequential damages resulting, directly or indirectly from any warranty expressed or implied or any other
failure of this product.
WHAT IS NOT COVERED BY THIS WARRANTY
Sunset Swings® sole obligation under this warranty is limited to either repair or replacement of parts, subject to the
additions below. This warranty neither assumes nor authorizes any person to assume obligations other than expressly
covered by this warranty.
NO CONSEQUENTIAL DAMAGES. Sunset Swings® is not responsible for economic loss; profit loss; or special, indirect,
or consequential damages.
WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies only in favor of the original
purchaser/user to whom delivered. Any such assignment or transfer shall void the warranties herein made and shall void all
warranties, express, implied or statutory. There are no warranties which extend beyond the description on the face hereof.
ALTERATION, NEGLECT, ABUSE, MISUSE, NORMAL WEAR AND TEAR, ACCIDENT, DAMAGE DURING
TRANSIT OR INSTALLATION, FIRE, FLOOD, ACTS OF GOD. Sunset Swings® is not responsible for the repair or
replacement of any parts that Sunset Swings® determines have been subjected after the date of manufacture to alteration,
neglect, abuse, misuse, normal wear and tear, accident, damage during transit or installation, fire, flood, or an ACT OF
GOD.
TRANSPORTATION COSTS. Sunset Swings® will accept parts covered under this warranty freight collect, provided that
shipment has received prior approval. Sunset Swings® is not responsible for any other transportation costs, but will ship
freight collect parts either repaired or replaced under these warranties.
WARRANTY VALIDATION AND CLAIM PROCEDURE. To validate your warranty please complete the enclosed
customer warranty registration card or go to www.sunsetswings.com and complete the online warranty registration.
All claims should include: model number, the serial number, proof of purchase, date of installation, and all pertinent
information supporting the existence of the alleged defect. In some cases photos may be required to support the claim.
Please call for pre-approval of shipment of warranty parts.
Sunset Swings®
Health In Motion
LLC
4945 East Hunter Ave
Anaheim, CA 9807
(877) 738-1729
(714) 738-1728 fax
Table of contents
Other Sunset Swings Baby Swing manuals
Popular Baby Swing manuals by other brands

Fisher-Price
Fisher-Price Rock-a-bye Cradlette 79615 instructions

stilum
stilum patis 3 Robinie Maintenance Instruction

Fisher-Price
Fisher-Price 79613 instructions

Fisher-Price
Fisher-Price M7590 manual

Graco
Graco Baby Swing owner's manual

Nags Head Hammocks
Nags Head Hammocks Deluxe Double Swing Assembly instructions

Sunnydaze Decor
Sunnydaze Decor DSL-521 manual

Garden Oasis
Garden Oasis EMERY D71 M20355 Use and care guide

Chad Valley Baby
Chad Valley Baby Circus Friends 580/9866 manual

Fisher-Price
Fisher-Price J7812 manual

Big Backyard
Big Backyard HILLCREST F23270 Installation and operating instructions

KIDWELL
KIDWELL LUPO user manual