Sunsky TS-9210 User manual

TS-9210
MIRROR PROJECTI O N CLOC K MANUAL
1

TS-9210 Mirror Projection Clock：
-- ----- ---- -- ----- ----
-- ----- ----- ------ ----- ----- ----- ----- ----- ----- - ----- ----- ----- ----- ----- ----- ----- - ---
18.5cm
-- ----- ----- ------ ----- ----- ----
-- ----- ----- -
-- ----- -----
-----------------------------------------
1.2cm
7.7cm
-- ----- --
-- ----- -----
---------
2.4cm
PM
AL2
AL1
2

4
CR2032 BATTERY
COMPARTMENT
REMOVABLE SUPPORT FRAME
HORN

Function and button indication diagram
PM
AL2
AL1
Time
PM
Projection lamp
Alarm clock 1
Alarm clock 2
3

down u p proje ct ZZmode 1 2
DOWN
UP/AM/PM
/AUTOMATIC SENSITIVITY
PROJECTION
ON/OFF MODE
SNOOZE/BRIGHTNESS ADJUSTMENT
ALARM2
PROJECTION LAMP
TYPE-C POWER PORT
USB OUTPUT PORT
ALARM1
5
PHOTOSENSITIVE PORT

2
1
Thank you for purchasing and using the TS-9210 Mirror Projection
Clock, the following is the user's operating guide.
1.Functions：
LED time display
The default is the brightest, six brightness levels adjustable
7 function buttons: down, up, project, , mode, ,
Projection function, projection can be rotated 180 degrees
4-bit time display: hour, minute
12-hour format and 24-hour format can be switched, default 24-hour format
The default display of the clock is 0:00 at power on
Two sets of alarm clocks, alarm clock 1 on the default display for 6:00, alarm clock 2 on the
default display for 13:00
Snooze function, 5 to 60 minutes adjustable
Automatic light-sensitive function
Night mode
ZZ
6

2.Power supply method：
1.TYPE-C power cord power supply (the product is always on when the power cord is powered).
2. CR2032 button battery (The battery is not powered and is only used to remember the time.).
Note: The product is shipped without batteries.
Type-c
(1.5m USB power cord)
Rear view Left view
7

3.Power on and reset：
The initial interface display of power-on reset
Default display after power on:
LED white light
Time: 0:00
Default time system:
24-hours format
8

4.Time setting：
1. In the time display mode,long press the【mode】enter the setting mode,the setting items are
displayed and flashing,and the setting sequence is: 12/24 hour setting→hour setting→minute
setting→exit. (As shown in Figure 1)
2. During setting, short press【up】to increase the value by 1; long press【up】to quickly increase
(8 steps/s); short press【down】to decrease the value by 1;long press【down】to quickly
decrease (8 steps/s).
3. If there is no operation within 10 seconds during the setting process, the current setting will be
saved automatically and the time setting mode will be exited.
9
1 2 H / 2 4 H s e t t i n g Hour setting Minute setting
Figure 1

5.Alarm setting：
10
Picture 2
Hour setting Minute setting Snooze time
AL1AL1
1. In the time display mode, single press【 】 /【 】to turn on or turn off the alarm, when the
alarm is on, the corresponding alarm symbol is displayed.(As shown in Figure 2)
2. In the time display mode, press and hold【 】 /【 】for 2 seconds to enter the setting mode,
after entering, the setting items will be displayed and flashing, and the setting sequence is:
hour→ minute→ snooze time.
12
12
3. During setting, short press【up】to increase the value by 1; long press【up】 to quickly
increase (8 steps/s); short press【down】to decrease the value by 1;long press【down】to
quickly decrease (8 steps/s).
4. Default snooze time is 5 minutes.

1. 2 minutes alarm time.
2. When the alarm sounds, the alarm symbol （ / ）flashes.
3. Snooze function: When alarm 1 or alarm 2 sounds, press【 】to enter snooze mode,
default 5 minutes. Press other buttons expect【 】 to stop the alarm.
6.Alarm and snooze：
1. Power on the LED display default brightest gear.
2. Single press【 】to switch the order of brightness: 100%→80%→60%→40%→20%→0%→
cycle. (As shown in Figure 3)
7.Brightness selection and automatic light-sensing：
ZZ
ZZ
ZZ
11
Figure 3
100% 80% 60% 0%
PM
AL2
AL1PM
AL2
AL1
PM
AL2
AL1PM
AL2
AL1PM
AL2
AL1
40% 20%
AL2
AL1

3. In the time display mode, long press【up】for 2 seconds to turn on or off the automatic
dimming function, ON for 2 seconds when open, OFF for 2 seconds when closed.(As shown in
Figure 4)
4. Automatic light sensing: the product automatically senses according to the strength of the
ambient light and darkness, the brighter the ambient light, the brighter the product backlight,
the darker the ambient light, the darker the product backlight.
down up pr oj ec t ZZmo de 12
Photosensitive port
Figure 4
12
Auto-sensing function is on Auto-sensing function is off
PM
AL2
AL1
PM
AL2
AL1

1. Night mode that night LED automatically into the low brightness display.
2. In the time display mode, single press【mode】to display the night mode ON (display ON) or
OFF (display OFF) state, the default is OFF state, the default night mode time is 18:00~6:00
automatically into the low light display, by short press【up】/【down】to select ON or OFF.
3. Night mode ON display state, long press【mode】to enter the inter val time setting, the setting
sequence is: start hour→start minute→ end hour→ end minute, start hour and minute setting,
the upper point of the COOL two points is lit, end hour and minute setting, the lower point of
the COOL two points is lit.(As shown in Figure 5)
8.Night mode：
13
Figure 5
START HOUR START MINUTE END HOUR END MINUTE

1. In the time display mode, single press【project】 to start the projection function, the
projection brightness is high bright, single press【project】again the projection brightness will
become low bright, press【project】again to close the projection function.(As shown in
Figure 6)
2. In the projection function on state, long press【project】, the projection screen will rotate 180
degrees. The projection column is adjustable: front 90 degrees, rear 90 degrees.
9.Projection function：
down up pr oj ec t ZZmo de 12
Projection column
Figure 6
high brightness
low brightness
14

RoHS
MADE IN CHINA
10.Charging function：
There is a USB output port on the side of the product, which can be used to charge cell phones
or other electronic devices through the USB output with an output voltage of 5V in the state of
using Type-c power cable connection for power supply.(as shown in Figure 7)
Figure 7
USB output port
15

16
TS-9210
镜面投影时钟说明书

TS-9210镜面投影时钟：
-- ----- ---- -- ----- ----
-- ----- ----- ------ ----- ----- ----- ----- ----- ----- ------ ----- ----- ----- ----- ----- ----- - ---
18.5cm
-- ----- ----- ------ ----- ----- ----
-- ----- ----- -
-- ----- -----
-- ----- ----- ------ ----- ----- ----- ----- ---
1.2cm
7.7cm
---------
-- ----- -----
-- ----- --
2.4cm
17
PM
AL2
AL1

功能及按键指示图
18
PM
AL2
AL1
时间
下午
投影灯
闹钟1
闹钟2

CR2032电池仓
可拆卸支撑架
喇叭
19

down u p proje ct ZZmode 1 2
减键
加键/上午/下午/自动感光功能
投影开关 设置按键
贪睡/亮度调节 闹钟1
闹钟2
投影灯
20
Type-c电源孔
USB输出孔
自动感光端口