Time now Invisible clock ii User manual

1. How to set Vibration Speed, Beep Volume and Number of Beeps.

Vibration Speed (1 = low, 2 = medium, 3 = high),

Beep Volume (1-3), Number of beeps (1-6). (Factory settings are Vibration = 3; Beep volume = 3; Beep number = 3)

2. How to set the Time and Date

(The Invisible Clock-II will automatically adjust the time for daylight savings time; please see details

below on how to turn this feature on or off). (TIP: Hold Set button down to rapidly advance counting)

3. How to use the Stopwatch

(TIP: You can start the Stopwatch and then leave this mode and it will continue to count. If you do not

need the stopwatch to run while using other functions, stop it before leaving this mode.

Time Now, Inc.

U.S. patent pending

Time Date

VIB & BEEP

Advance to Vib

& Beep Mode

Time Date

VIBRATE 3

Enter Adjustment

mode

Time Date

VIBRATE 1

Adjust

vibration

Time Date

BEEPVOL-2

Advance to beep

volume

Time Date

BEEPVOL-3

Adjust beep

volume

Time Date

BEEPNO #3

Advance to

number of beeps

Time Date

BEEPNO #4

Adjust number

of beeps

Time Date

VIB & BEEP

Press to save

settings

Time Date

TIME&DATE

Advance to

Time & Date

5:12

SET TIME

Press twice,

hours will blink

6:12

SET TIME

Advance to

minutes

pm6:15

SET TIME

Adjust minutes

8-14

SET TIME

Advance to

month

9-14

ET TIME

Select month

9-14

SET TIME

Advance to

day

6:12

SET TIME

Select hour

(note AM/PM)

Time Date

YEAR=2003

Advance to

Year

9-15

SET TIME

Adjust Day

Time Date

AYLSAV=T?

Hold for 3 seconds

to access daylight

savings time on/off

Time Date

TIME&DATE

Press twice to

save all settings

Time Date

AYLSAV=on

Press to turn

daylight savings

time on or off

ON =

OFF = T?

Time Date

YEAR=2003

Select Year (do not

push if correct year

is shown)

TIP:

If you go past

the year you

want, continue

counting past

2040, to begin

again at 2003.

Time SW

STOP-WATCH

Advance to

STOP-WATCH

Time SW

0 : 00 : 00 : 00

Enter mode

Time SW

0 : 00 : 01 : 35

Start

Stopwatch

Time SW

0 : 00 : 24 : 32

Stop

Stopwatch

Time SW

0 : 00 : 00 : 00

Reset to zero

Time SW

0 : 00 : 37 : 21

Press while Stopwatch is

running to pause: Display

freezes, stopwatch still counts

Time SW

0 : 00 : 43 : 28

Press to resume

display of counting

after pausing

Please Read These Notes about Settings Protection:

(settings protection engage automatically)

1. Setting Protection – To protect the Timer, Meeting Timer and Custom Timer settings from erasure by accidental button presses, the

Invisible Clock-II has a “button auto-lock” feature (which engages automatically). To exit from the Timer or Meeting Timer you have

to press the two middle buttons simultaneously, and then press the Mode button to exit. To exit from the Custom Timer you only have

to press and hold the two middle buttons simultaneously for 2 seconds.

2. Setting Protection for Alarms - To protect the 12 Alarms from accidental erasure: Go to Alarms mode and press and hold the Enter

button for 3 seconds before you can enter the Alarms Mode before setting or changing any Alarm.

To Start:

Install a AAA battery in the back of your Invisible Clock.

The Invisible Clock-II has 7 modes, accessed by the Mode button:

•Vibration and Beep adjustment (VIB & BEEP): Use to adjust Vibration Speed

(1 = low, 2 = medium, 3 = high), Beep Volume (1-3), Number of beeps (1-6).

•Time and date adjustment (TIME & DATE): Use to set time and date.

•Timer (TIMER SET): Use for simple timing or to repeat a time over and over.

•12 Alarms (ALARMS SET): Use to set up to 12 alarms in a 24-hour period. Alarms

programmed in this mode will signal no matter what other mode the unit is in.

•Meeting Timer (MEET-TIMER): Use for meetings, presentations or to track time

during any interval. The Meeting Timer vibrates at ½ way, at 5 minutes before time’s

up, and at time’s up, for any time interval set between 10 –120 min.

•Custom Timer (CUSTOM TMR): Use to set any countdown time of up to 60

minutes, and program with up to six custom alerts to go off at any time in this period.

Can also set it to repeat, or count-up after countdown is complete.

•Stopwatch

(STOP

WATCH): use to count time for any event.

Invisible Clock







II Operation Instructions

SETTING THE ADJUSTMENT & TIMING MODES

TIME DATE

T I M E R S E T

Mode Enter Set Lite

Display

Mode button

Enter button

To Exit from Timer and

Meeting Timer modes

push simultaneously, then

press Mode button to exit

Alarm Switch

Vibr=vibration

O = off

Beep = beep

Lite: Press

once and

stays on for

12 seconds

Set button

Hold down for

rapid counting

To Erase an

Alarm: Go to the

Alarm you want to

erase, then press

Enter & Set

simultaneously; to

exit press Mode.

TIP 1

To set multiple alarms or to check your set alarms, use the Enter button to scroll through set

alarms. To set additional alarms go to a blank setting, then continue as in drawing #3 above.

TIP 2

: Vibration alert = 20 seconds. Press any button to stop alert. If you press the Lite button, it

stops the alert and engages the snooze feature

see

Note 3

below ab

out the snooze button.

Note 1.

A set alarm will signal in all other modes unless alarm switch (on side of unit) is set to O (off). An alarm

remains set after its time has passed, and will sound again every successive day until it is erased.

Note 2.

Set alarms are automatically organized in the order of next to go off, according to the time of day. In other

words, when you check your set alarms, ALARM 01 will be the next to signal, then ALARM 02…etc.

Note 3.

SNOOZE button - When an alarm signals, press the light button to turn off the alarm and engage the

snooze feature; the alarm turns back on automatically after 5 minutes. You can only do this once with each alarm.

Erasing an Alarm

: To erase an existing alarm, (a) use the Mode button to advance to “ALARMS SET”; (b) use the Enter button to

select the number of the alarm that you wish to erase; (c) Press both the Enter and Set buttons simultaneously. This will erase the

alarm’s time, and therefore will erase the alarm itself.

Changing the Time of an Existing Alarm

:To change the time of an existing alarm, (a) use the Mode button to advance to

“ALARMS SET”; (b) Use the Enter button to select the number of the alarm that you wish to modify; (c) Use the Set button to change

the minutes, then press the Enter button to shift to the hours, which you may change with the Set button; (d) Press the Mode button to

accept the change.

pm2:53

AM -:--

ALM01-SET

Hold for 3

seconds to enter

mode

pm2:53

8-13

ALARMS SET

Advance to

ALARMS SET

pm2:53

:30

ALM01-SET

Advance to hours

(Note: AM/PM)

pm2:53

7:30

ALM01-SET

Set this alarm

pm2:53

:30

ALM01-SET

Adjust hours

(Note: AM/PM)

pm2:53

AM -:--

ALM02-SET

Advance to set

another alarm (to

Exit press Mode)

pm2:53

AM -:

ALM01-SET

Adjust minutes

Continue as in

step 3 in this

line. Finish by

setting the

alarm with the

mode button

5. How t

o set Alarms.

Up to 12 Alarms may be set. NOTE: The Alarm auto-protect feature requires that you hold the Enter

button down for 3 seconds to enter the Alarms mode - see instructions below on how to do this.

Time now Alarm time being set Alarm number

pm2:33

TIMER

00 : 10 : 30

Press until

appears in screen

How to

set the

Timer to

Repeat

over &

over.

First set the countdown time

as shown in the above steps,

then before starting the timer,

press the "Enter" button until

R appears in the left of the

display, then press Mode

button to start the timer.

pm2:33

TIMER

01 : 10 : 13

Press simultaneously

until display blinks

pm2:33

TIMER SET

Exit

To EXIT during a countdown

NOTE

The Timer saves the last programmed time. When countdown is complete, this time is displayed. To use this time again, press

Mode

to start the timer with this time. If you wish to use this time again but have gone to another mode, go to TIMER SET via the Mode button, press

Enter once and press Mode to start this countdown time (you can wait as long as you wish to press Mode to start the Countdown).

How to

ERASE a

countdown

time and

program a

new one

pm2:33

TIMER

00 : 00 : 00

Press to erase

countdown time

pm2:33

8-13

TIMER SET

erase countdown

time when countdown

is not running, advance

to Timer Set.

pm2:33

TIMER

01 : 10 : 13

Enter Timer

mode

pm2:33

TIMER

00 : 00 : 00

Press to erase.

pm2:33

TIMER

01 : 10 : 13

erase during a

countdown, press

simultaneously

Then to program in a

new countdown time

proceed as shown

starting with the 3rd

drawing in the very

first line at the top of

this page

pm2:33

TIMER SET

Advance to

Timer Set

pm2:33

TIMER

00 : 00 : 00

Enter Timer

mode

pm2:33

TIMER

00 :

: 30

Advance to

minutes

pm2:33

TIMER

00 :

: 30

Select minutes

pm2:33

TIMER

: 10 : 30

Advance to

hours

pm2:33

TIMER

: 10 : 30

Select hours

pm2:33

TIMER

00 : 00 :

Select Seconds

(press "Enter" to

skip seconds)

4. How to use the Timer.

The Timer can be set to countdown once, or set to repeat over and over.

Hours Minutes Seconds

pm2:33

TIMER

01 : 10 : 29

Start countdown;

Countdown time in this

example =1hour, 10

minutes, 30 seconds.

When countdown = 0,

alarm vibrates or beeps

NOTE: Vibration

alert lasts for 20

seconds. Press any

button to turn off

vibration or beep.

pm2:33

CTMR

RPT : 20 : 00

Press repeatedly until

RPT (repeat)

STEP 3:

to One

Countdown, to

Repeat, or to

Count-Up

pm2:33

CTMR

C-UP : 20 : 00

Count-Up

(after countdown

is complete)

pm2:33

CTMR

: 20 : 00

One countdown

only (blank on left)

STEP 4:

tart

Countdown

(if timer doesn't

start, press Enter

then press Mode

to start)

NOTE: You can

press Mode after

setting 1, 2, or more

Alerts; then to start

the timer, press

Enter once, and

Mode once.

Press to save all

programming and start

countdown session

pm2:33

CTMR

C-UP : 19 : 33

6. How to use the Custom Timer.

First set a countdown time of from 3 seconds to 60 minutes. Then program up to 6

unique alerts to signal within this countdown time. The countdown time can be set to countdown once, to repeat over and over,

or to count-up after countdown completes. NOTE: If you set an alert at 10 minutes, it will signal when there are 10 minutes left

in the countdown; set an alert at 1 second to signal at the end of countdown.

STEP 1:

Program

Countdown

Time

pm2:33

CTMR

TIME :

:30

Adjust minutes

(countdown time =

40 minutes & 30 seconds)

pm2:33

8-13

CUSTOM TMR

Advance to

CUSTOM TMR

pm2:33

CTMR

TIME: 00 :

Adjust seconds

pm2:33

CTMR

TIME :

:30

Advance to

minutes

pm2:33

CTMR

TIME 00 :

Enter

adjustment

mode

Proceed to

STEP 2

below

Alert A

= 5 second vibration... or if alert switch (on the side of the unit) is set to beep = 1 beep

Alert B = 5 second vibration, 5 second space, 5 second vibration…………or……….. = 2 beeps

Alert C = 10 second vibration………………………………………………or………. = 3 beeps

Alert D = 10 second vibration, 7 second space, 10 second vibration………or……… = 4 beeps

Alert E = 20 second vibration………………………………………………or……… = 5 beeps

Alert F = 2 second vibration……………………………………………… or……… = 6 beeps

STEP 2:

Program up to

6 alerts within

countdown

time

pm2:33

CTMR

A : 00 : 00

Advance to

Alert A

pm2:33

CTMR

A :

:01

Advance to

minutes

pm2:33

CTMR

A :

: 01

Adjust minutes

pm2:33

CTMR

B : 00 : 00

Advance to

Alert B

Set Alert B the

same way as you

set A. You can

set one or all of

the alerts

A,B,C,D,E,F.

After setting the

alerts you want,

proceed to

STEP 3 below

TIP: To skip an

alert during

programming,

press the Enter

button two times

pm2:33

CTMR

A : 00 :

Adjust seconds

Stop

Count-

down

This action

stops the timer

and puts it in

the ready

position to

start again

pm2:33

CTMR

C-UP : 20 : 00

Press two middle buttons

simultaneously for 1 second

or less to stop countdown

Exit

Mode

Restart

count-

down

Press to restart

countdown

pm2:33

CTMR

C-UP : 19 : 49

Press two middle

buttons simultaneously

and hold for 2

seconds to exit mode

pm2:33

8-13

CUSTOM TMR

Then

ERASE

ALL

program-

ming

pm2:33

CTMR

ERASEALL=T

Hold for 3seconds

pm2:33

8-13

CUSTOM TMR

Start from here

pm2:33

CTMR

ERASED ALL

Press to erase

Restarting

Timer when

it is

programmed

pm2:33

T 08:00

ADB

Press to enter Press to start

pm2:33

CTMR

C-UP : 19 : 49

pm2:33

8-13

CUSTOM TMR

Start here

NOTES for the Custom Timer:

1. During programming, once you have selected all the alerts you need, you can press Mode at any time to save your programming. To

start the timer, press Enter once, then Mode once.

2. Once the custom timer is programmed, it will remain programmed until all programming is erased.

3. To restart timer after countdown completes for one-time countdown or for count-up, press Mto restart (at any time during count-up).

4. Set any alert to 1 second to have a signal at end of countdown.

. From "CUSTOM TIMER" you can press

Enter

and wait until ready to start countdown by pressing

Mode

Checking and changing programming (without erasing all programming)

pm2:33

8-13

CUSTOM TMR

Start here

pm2:33

T 08:00

#A= 01:00

Press and hold for

3 seconds to see

alerts

pm2:33

T 08:00

#B= 01:00

Press to scroll

through existing

alerts

pm2:33

T 08:00

#B= 01:00

Push simultaneously

to allow this alert to

be changed

pm2:33

T 08:00

#B= 01:15

Press to

change

seconds

pm2:33

T 08:00

#B= 01:15

Advance to minutes

pm2:33

T 08:00

#B= 03:15

Press to accept

changes. Press

again to exit mode

pm2:33

T 08:00

#B= 03:15

Press to

change

minutes

MEETING TIMER NOTES:

1. Once a meeting time is started, it will repeat every 1/2 hour for durations of 10-30 minutes, and repeat every hour for durations of 31-60 minutes,

and repeat every other hour for durations of 61-120 minutes. For example, program a meeting time of 50 minutes and start it on the hour, it will go

for 50 minutes, wait 10 minutes and then begin again on the next hour. If you start this 50 minute meeting time at 10 minutes after the hour, it will go

for 50 minutes, wait 10 minutes and begin again at 10 minutes after the next hour.

2. Meeting times of 30, 60, 120 minutes will repeat back to back automatically. For all other meeting times, there will be a space before the meeting

timer repeats. For example, for a meeting time of 25 minutes, it will go for 25 minutes, wait 5 minutes and begin again. For a meeting time of 40

minutes it will go for 40 minutes, wait 20 minutes and begin again. If you want a meeting time to repeat back to back and it is not 30, 60 or 120

minutes, you will need to restart the meeting timer manually at the end of each meeting time by pressing the two middle buttons simultaneously, and

then pressing the Enter button to re-start the meeting timer at that time.

3. When the meeting timer is in operation, it does not show countdown. It only shows "ON" and the total meeting duration.

7. How to use the Meeting Timer.

Set for any time between 10 minutes and 120 minutes. Signals at 1/2 way through,

5 minutes before the end, and at the end of meeting time. Each signal is unique. Repeats on the 1/2 hour, 1 hour, or every 2 hours.

pm2:33

MT-TMR

ON : 00 : 30

Turn meeting timer back ON

pm2:33

8-13

MEET-TIMER

Advance to

MEET-TIMER

pm2:33

MT-TMR

ON : 00 : 30

Start meeting

timer

pm2:33

MT-TMR

MEET-TIMER

Push to EXIT

(this will only work

when in OFF position)

pm2:33

MT-TMR

OFF : 00 :

Adjust minutes

(10 to 120 min.)

pm2:33

MT-TMR

OFF : 00 : 30

Push simultaneously

to turn OFF

EXIT

Back ON

pm2:33

MT-TMR

OFF 00 : 10

Enter adjustment

mode

pm2:33

MT-TMR

OFF 00 : 30

Enter adjustment

mode

TIP #1

: The meeting time

that was last programmed

is saved when you exit.

When you return to this

mode and wish to re-use

this meeting time, follow

these steps.

pm2:33

8-13

MEET-TIMER

Advance to

MEET-TIMER

pm2:33

MT-TMR

ON : 00 : 30

Start meeting

timer

TIP #2:

ERASE a meeting time

go to MEET-TIMER,

press Enter, press Set; this will erase the last used meeting

time and allow you to set a new time by pressing Set

again. Hold Set button down for rapid counting.

Warranty:

Time Now, Inc. (TN) warrants this timer is free from defects in material and workmanship that result in product failure during normal use, according to the following

terms and conditions: The limited warranty for this product extends for 1 year beginning on the date of purchase of the product. The limited warranty extends to the original

purchaser of the product and is not assignable or transferable to any subsequent purchaser/user. During the limited warranty, TN will repair, or replace the timer unit, at TN’s option;

or replace any defective parts, or any parts that will not properly operate for their intended use with new items if such repair or replacement is needed because of product malfunction

or failure during normal usage. No charge will be made to the consumer for any such parts or repair labor. The limited warranty does not cover defects in appearance, cosmetic,

decorative or structural items. TN shall not be liable for any other losses or damages. These remedies are the consumer’s exclusive remedies for breach of warranty. The consumer

shall have no coverage or benefits under this limited warranty if any of the following conditions are applicable: (a) The product has been subject to abnormal use, abnormal

conditions, improper storage, exposure to moisture or dampness, unauthorized modifications, unauthorized repair, misuse, neglect, abuse, accident, alteration, improper installation,

or other acts which are not the fault of TN, including damage caused by shipping; (b) the product has been damaged from external causes such as collision with an object, or from

fire, flooding, sand, dirt, windstorm, lightning, earthquake or damage from exposure to weather conditions, an Act of God, or battery leakage, or theft. If a problem develops during

the limited warranty period, the consumer shall take the following procedure: Return the product to TN, 3325 Garnet Ave., Rosamond, CA 93560 USA. Include a return address,

phone #, description of the problem. TN will repair or replace the product under the limited warranty within 15 days after receipt of the product by TN. TN shall not be liable for

special, incidental or consequential damages, including but not limited to, loss of anticipated benefits or profits, loss of savings or revenue, punitive damages, loss of use of the

product or any associated equipment, cost of capital, cost of any substitute equipment, downtime, the claims of any third parties including customers, and injury to property, resulting

from the purchase or use of the product or arising from breach of the warranty, breach of contract, negligence, strict tort, or any other legal or equitable theory, even if TN knew of

the likelihood of such damages. TN shall not be liable for delay in rendering service under the limited warranty, or loss of use during the period that the product is being repaired.

INVISIBLE CLOCK

II PROBLEM SOLVING:

1. The Unit appears stuck in the Timer or Meeting Timer: try pushing the two middle buttons simultaneously (just for a second) until the display blinks, and

then press the mode button to exit. To EXIT the Custom Timer, press and hold the two middle buttons for 2 seconds.

2. The Meeting Timer does not appear to be working: The Meeting Timer does not show countdown when in operation. It only shows "ON" and the total time

of the meeting or interval set.

3. No alert is vibrating for the Meeting Timer: Make sure you have a meeting time set & the Meeting Timer is ON; the display should show for example: “ON

00:45”. Also, make sure the vibration switch on the side of the unit is set to “V” for vibration.

4. The vibration strength is not strong enough: Try setting the vibration to “3, high”. See “#1. How to set vibration speed…” first page of instructions.

5. Alarms do not appear to organize correctly when setting multiple alarms: The unit automatically organizes the set alarms in the order of next to go off. So

when you set or check your alarms, the unit will display Alarm 01 as the next to signal, and Alarm 02 as the next after that one and so on.

6. You cannot enter the Alarms mode to set alarms: Hold down the Enter button for 3 seconds to enter the Alarms mode (this protects alarms from accidental

erasure.

7. The vibration is too long for the Timer and Alarms: Vibrations in these modes = 20 seconds. To stop the vibration, push any button. In the Alarms mode, one

push of the "Lite" button stops the alert and also engages the snooze feature, and an alert will signal again in 5 minutes.

8. A pulsed vibration is normal in low and medium vibration settings.

9. The Stopwatch cannot be used to set an alert.

10. When to Change the Battery - The battery is low when the backlight becomes dim and the vibration is noticeably slower / or the beep volume is lower. The