Super Amart LE FRANSCHHEOK 54391 User manual

1 54391
Imported by Super A-mart Pty Ltd, Qld, Brisbane Australia.
or any assistance with assembly or for missing parts please phone
Super A-mart Ewing Road, Customer Service ree call 1800 351 084
ASSEMBLY INSTRUCTION
LE RANSCHHEOK 6 DRAWER DRESSER WITH MIRROR
ITEM CODE 54391
Imported by Super A-mart Pty Ltd, Qld, Brisbane Australia.
or any assistance with assembly or for missing parts please phone
Super A-mart Ewing Road, Customer Service ree call 1800 351 084

2 54391
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product
2. Take care when lifting. Product should be assembled as near as possible to the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads

3 54391
PARTS LIST
1 DRESSER
2 MIRROR
3 SUPPORT BAR
a.
Bolt
M6x40
12pcs
b
. Allen key M4
1pc
c
.
lat Washer
Φ
6.5x
Φ
19
12pcs
d
. Lock Washer
Φ
6.5x
Φ
9
12pcs

4 54391
ITEMS REQUIRED
•Attach Support Bar ( 3 ) to Dresser (1) using bolts (a) with flat
washer (c) and lock washer (d).
•Tighten with Allen Key (b).
a. Bolt M6x40
6pcs
b. Allen key M4
1pc
c. lat Washer Φ6.5xΦ19
6pcs
d. Lock Washer Φ6.5xΦ9
6pcs

5 54391
ITEMS REQUIRED
•Attach mirror (2) to Support Bar (3) with bolts (b) and lat washer
(c) and lock washer (d).
•Tighten with Allen Key (b).
b. Bolt M6x40
6pcs
b. Allen key M4
1pc
c. lat Washer Φ6.5xΦ19
6pcs
d. Lock Washer Φ6.5xΦ9
6pcs

6 54391
SAFETY BRACKETS INSTRUCTIONS
1. Attach one bracket to the wall, with the long screws as shown. Make
sure to attach the bracket into a stud. If mounting onto brick or
masonry, you will need to acquire wall anchors.
2. Attach a bracket to the furniture frame under the top with the short
screws provided.
3. Move the furniture into its final position. Thread a strap through the
bracket as shown in the illustration, tighten strap until snug. Do not
over tighten.
4. Make sure the bracket is firmly attached to the wallboard and
furniture, and the strap is snug.

7 54391
ASSEMBLY IS COMPLETE

Care label for timber items
•A multi-step finish is applied to all our furniture, but all wood comes from nature. Because
of this, there will be natural variations in surface texture and grain like knots, mineral
streaks and sap runs that may affect the finish. These differences in character are not
defects, but distinctions that make each piece of furniture unique.
•Our furniture is built to last. ollowing these steps for basic care should protect your
investment for years to come.
•Dust frequently with a clean damp lint-free cloth. This will help remove abrasive build up
which can damage a finish over time.
•Do not place hot objects on any furniture surface. Always use a hot plate or placemat.
Laminate and lacquer finishes on table tops provide added scratch and heat resistance to
our furniture, but they can still be damaged without proper care.
•Avoid exposing your furniture to strong sunlight, heat outlet, open windows or dampness.
Prolonged exposure to direct sunlight can fade the finish of your furniture, while extreme
temperature and humidity changes can cause cracking or splitting.
•Do not expose your furniture to any liquids. Never allow water to sit on your furniture.
Alcohol, nail polish and perfume are also dangerous as they will dissolve the lacquer finish
on contact and may require professional repairs.
•Do not allow plastic to come in direct contact with your furniture. Chemicals in the plastic
of placemats etc may soften and mark the finish if left in contact with the furniture for a
period of time.
•If the glass is chipped or broken, stop using the product and consult the place of purchase
•Do not drop, drag or strike glass
•Do not sit or stand upon the glass surfaces
•Do not place very hot or cold items on the glass unless adequately thick table mats are
used to prevent such items coming in contact with the glass
•Do not place heavy objects on glass
•Avoid scratching the glass or using as a chopping surface
•Do not strike the glass with hard or pointed items
•When cleaning the glass panels, use a damp cloth with washing up liquid or soft soap if
necessary. Do not use washing powders or any other substances containing abrasives that
may potentially scratch the glass