Super Vac SVU-50 User manual

USER MANUAL
OPERATOR MANUAL SVU-50

OPERATOR MANUAL
2Revised 6-2023
OPERATOR MANUAL
This manual covers the how to use the Super Vac SVU.
For additional instruction, view installation videos at:
SVU OPERATION: .................................. bit.ly/svu-operation
SVU SECUREMENT: .............................bit.ly/svu-securement

CONTENTS
Contact Info ........................... 3
Unit Operation ..................... 4-5
Control Panel........................4
Operation .............................5
Securement ........................ 6-8
Parts ................................... 6
Back Bar ..............................7
Turnbuckles..........................8
Maintenance .......................... 9

SVU-50
3
Revised 6-2023
THANK YOU
Please allow us to express a simple thank you for investing in a SUPER VAC product. As a company we are
dedicated to producing the very best and most versatile fan package available. We take great pride in the quality
of our work and hope that you will nd many years of satisfaction from the use of this equipment.
Should you have any problems with your product please do not hesitate to contact us.
Super Vaccum Mfg Co, Inc
3842 Redman Drive
Fort Collins, CO 80524
PHONE: [phone]
FAX: [phone]
WEB: www.SuperVac.com

OPERATOR MANUAL
4Revised 6-2023
SVU CONTROL PANEL:
RAISE AND LOWER
ROTATE LEFT TO RIGHT
TILT BACK AND FORWARD
START ENGINE MASTER POWER
POWER ON
MONITOR
LIGHTING
POWER OFF
LOW/HIGH IDLE
RPMS
ReGen ON/OFF

SVU-50
5
Revised 6-2023
STEP 1: START
To start the unit, turn the key to on and the dash will
light up. (Wait a moment.)
STEP 2: MASTER POWER
When that is on, turn you master power on. That will
turn your fuel pump on and you’ll be ready to start.
STEP 3: TURN KEY
Turn the key all the way to the right to start.
PROPER USE
Get engine running and while at idol raise and
position your unit where you want it to be before
you ramp up your RPMS.
STEP 5: RAMP UP RPMS
LIghting should be above 1500 RPMs
running the LED lights.
STEP 4: SET POSITION
Raise, lower, rotate and tilt the fan head into position.

OPERATOR MANUAL
6Revised 6-2023
SVU SECUREMENT: How to tie down the SVU unit for transport.
CURBSIDE FLOOR HOOK
STREETSIDE FLOOR HOOK
CURBSIDE UNIT TIE-DOWN
STREETSIDE UNIT TIE-DOWN
BACK FLOOR STRAP
FIRST: Turn master power on, tilt forward.


SVU-50
7
Revised 6-2023
STEP 1: APPLY BACK STRAPS
Utilize tilt motion to get the unit in place.

B: Release rear strap. C: Connect rear strap to eyelet. D: Use Ratchet Strap to secure.
* (Repeat Steps B,C, and D on the opposite side.)

OPERATOR MANUAL
8Revised 6-2023
STEP 2: APPLY FRONT STRAPS
A: With back straps tight and in place
(step 1), hook ratchet straps into
both front oor loops.
B: Hook opposite side of ratchet straps onto front unit tie downs. C: Tighten both front ratchet straps until
tight and secure.
Make sure all straps are removed before operating unit.

SVU-50
9
Revised 6-2023
MAINTENANCE:
ENGINE:
Refer to Kubota Supplement for Engine Maintenance.
SCISSOR LIFT:
Refer to Advance lift supplement for Scissor Lift Maintenance
SVU UNIT:
After each use:
;Clean and inspect unit after each use.
;Keep debris clean from shroud and blade area.
;Inspect covers and fasteners etc. for tightness on a regular basis.
WARNING
Never operate with any guards, covers or other components
not properly in place and in good condition.
!