Super Vac V18-BL User manual

VENTILATOR USER GUIDE MODEL V18-BL

POSITIVE PRESSURE VENTILATOR
2
V18-BL PPV User Guide Revised 9-2019
USER GUIDE
This manual covers the description, cautions, operation, and maintenance of the Super Vac V18-BL.
Please take the time to read this manual before operating the ventilator.
Save this guide for future reference.
CONTENTS
1. BREAKAGE OR DAMAGE DURING SHIPMENT ................................................................................................... 3
2. GENERAL DESCRIPTION AND SPECIFICATIONS ................................................................................................. 4
3. PRODUCT SAFETY PRECAUTIONS ...................................................................................................................... 4
4. BEFORE OPERATING VENTILATOR .................................................................................................................... 5
5. OPERATION ....................................................................................................................................................... 6
6. CHARGING THE BATTERY PACKS ............................................................................................................................. 7
7. MAINTENANCE AND REPAIR ................................................................................................................................... 7
8. WARRANTY ....................................................................................................................................................... 8
9. CONTACT INFORMATION .................................................................................................................................. 9
10. PARTS LIST ......................................................................................................................................................... 10
11. EXPLODED VIEW ............................................................................................................................................... 11

POSITIVE PRESSURE VENTILATOR
3
V18-BL PPV User Guide Revised 9-2019
1. Breakage or Damage During Shipment
The transportation company is fully responsible for all shipping damage and will resolve problems promptly if you handle it correctly.
Please read these instructions carefully.
Examine the contents of all shipping cases. If you find any damage, call your transportation agent at once and have them make a
description on the freight or express bill describing the damage and the number of pieces. Then write us and we will send you the
original bill of lading. Get a claim blank from the express or truck company. Fill the claim form out. Attach the claim blank to the
original bill of lading together with a copy of our invoice. Attach a memo on which you show the value of the damaged goods. Mail or
hand these papers to your local transportation agent. They will process your claim with reasonable promptness.
Please note, we cannot and will not enter claims for damages. If we filed claim here, it would be sent to your local freight agent for
verification and investigation. This time can be saved by your filing the claim directly. Every consignee is on the ground floor and in
contact with the local agent who inspects the damaged goods, and thus, each claim can be given individual attention.
Since our goods are packed to comply with the regulations of all railroad, truck, and express companies, we cannot allow deduction
from any invoice because of any damage, however, be sure to file your claim promptly. Our goods are sold F.O.B. factory. We take
receipt from the transportation company certifying that the goods were delivered to them in good order, and our responsibility
ceases.
It is seldom that any breakage or damage occurs in any of our shipments, and in no case will the customer be out any expense if they
follow the above instructions.
Be sure to keep all damaged goods subject to examination of the truck or express company inspector, who may call on you some time
later. These damaged goods, of course, will belong to them, and they will inform you what to do with them. If you dispose of these
damaged goods, your claim may not be paid.

POSITIVE PRESSURE VENTILATOR
4
V18-BL PPV User Guide Revised 9-2019
2. General Description and Specifications
Super Vac ventilators are specifically designed to provide a convenient and portable source of air. Super Vac positive pressure
ventilators are tested to AMCA Standard 240-15, for use in extreme conditions.
Model # RPM Motor H x W x D Weight
V18-BL 2000 1 HP Variable Speed DC 25.75” x 25.75” x 11.75” 46 lbs
Specifications are subject to change without notification. Refer to model decal affixed to ventilator to determine actual specifications.
This ventilator is designed for high powered air movement. Super Vac’s propeller produces a greater intake of air and reduces turbulence at
the tips. Each blade is dynamically balanced for high efficiency and long life.
3. Product Safety Precautions
• Do not use the ventilator for purposes other than its’ intended use.
• Wear eye and ear protection when operating the ventilator.
• Never operate ventilator while fatigued.
• Do not disassemble or modify the ventilator in any way. Doing so may lead to
mechanical failure or personal injury.
• Do not wear loose clothing that could become entangled in the operating ventilator.
• Never permit anyone to operate ventilator without proper instruction.
• Do not operate ventilator without proper inlet or outlet guards in place. If guards are
missing or damaged, contact factory for replacements.
• Do not place fingers or other foreign objects through inlet or outlet guards. Should a foreign
object enter the ventilator, immediately stop motor. Be certain all mechanical motion has
stopped. Do not use with any power voltage other than the indicated voltage.
• Never handle energized power cords with wet hands.
• Do not place or operate ventilator on unsteady tables, slanted surfaces or other unstable
surfaces. Never use this ventilator in any explosive environment.
• Never let extension cords or plug connections lay in water. Locate the ventilator so that it
cannot fall into water inadvertently.

POSITIVE PRESSURE VENTILATOR
5
V18-BL PPV User Guide Revised 9-2019
4. Before Operating Ventilator
• This ventilator has been designed to work best with either the Milwaukee M18 REDLITHIUM High Output XC8.0Ah or HD12.0 batteries.
• This ventilator will work with any M18 battery from the Milwaukee brand.
• A complete inspection of the ventilator should be made prior to operation.
• Check all threaded fasteners for proper tightness.
• Check ventilator inlet and outlet guards for obstructions. Check and remove from immediate surrounding area any objects that could be drawn into the
ventilator intake.
• Replace damaged or missing guards before operating ventilator.
• Never store or carry the battery pack so that metal objects can contact exposed battery terminals. Transporting batteries can possibly cause fires if the
battery terminals contact loose nails, screws, keys, hand tools and the like.
• If using shore or mains power:
o Never use power cords with frayed, cut, or brittle insulation.
o Inspect power cord plug for proper connections to the ground fault interrupter circuit.
Airflow vs Setback
11,000
10,000
9,000
8,000
7,000
9,209
10,230
MAXIMUM
AIRFLOW
↓
10,103
8,873
8,131
7,854



10º


15º
20º 25º
30º
0
21 ft 18 ft 15 ft 12 ft 9 ft 6 ft 3 ft 0
6.5 m 5.5 m 4.5 m 3.6 m 2.7 m 1.8 m 1 m
Setback (ft, m)
Airflow (CFM)
6,000
5,000
4,000
3,000
2,000
1,000
5º

POSITIVE PRESSURE VENTILATOR
6
V18-BL PPV User Guide Revised 9-2019
0
200
400
600
800
1000
1200
1400
1600
1800
2000
0 10 20 30 40 50 60 70
Blade RPM
Runtime [min]
Battery Runtimes
[at max speed]
HD12.0 Battery
XC8.0 Battery
Low Battery Warning
5. Operation
• Use caution not to direct toxic fumes into confined spaces with the ventilator. Please refer to the Super Vac Training Manual for
Smoke Ventilation for comprehensive instruction on effective ventilation practices.
• Insert a Milwaukee M18 battery. Only one battery is necessary. Battery will click when fully inserted.
• Battery removal will get easier with more remove/replace cycles. The Battery Adapter & M18 Battery interface is required by Milwaukee.
• Fan will need to be reset (turned off & on) if a new battery is inserted.
• If fan is not reset, then the fan will not recognize the new battery and run until previous battery is empty.
• If using shore (mains) power, use an extension cord to connect to 110 – 240V AC.
• Press and hold power button until blue backlight indicates powering up.
• When the fan is on, it will need to run at the minimum speed allowed by Milwaukee. (This feature is to protect the batteries from small parasitic draws)
• Turn speed control clockwise until desired speed is reached.
• Power button will indicate approximate power left. (It is normal for colors to flicker back and forth if 2 batteries are being used)
• Green: 50 - 100%
• Yellow: 20 - 50%
• Red: 0 - 20% (Low Battery Warning: Front Facing LED will also flash if turned on)
• To turn off, press and hold power button until blue backlight shows.
*Runtimes dependent on air
density, temperature and age of
batteries. Test data shown taken at
5000ft elevation, 25% RH, 70°F
with new batteries.
*Air density is primarily affected by
elevation, humidity and
temperature.
*At temperatures below freezing
expect battery life to decrease.
*Other M18 Batteries will operate
the fan, but at reduced runtimes.

POSITIVE PRESSURE VENTILATOR
7
V18-BL PPV User Guide Revised 9-2019
CAUTION:
• Do not store battery packs or
chargers above 120°F (50°C) or in
direct sunlight.
• Never use charger or batteries in
explosive atmospheres.
• Never attempt to open the
battery pack. If cracked or
damaged, return it to a
service center for recycling.
• Do not splash or immerse
charger in water or other
liquids.
6. Charging the Battery Packs
- Remove Milwaukee batteries from fan.
- Insert in Milwaukee Charger. Use only Milwaukee brand battery chargers.
- When the battery pack temperature is outside the charging range (40-105°F or 5-40°C),
the red light on the charger will flash and the battery will not charge.
- Once the battery pack is within the acceptable temperature range, normal charging will
take place.
- Using the Milwaukee RapidChargerTM, a 12 Amp hour battery will recharge in 120
minutes and an 8 Amp hour battery will recharge in 90 minutes.
- Other Milwaukee chargers, including units that work with vehicle DC power, may take
longer to fully charge the batteries.
7. Maintenance and Repair
Maintenance should only be performed by experienced and trained personnel. If you have
any questions, please contact Super Vac before attempting any maintenance at
www.supervac.com or 1-800-525-5224.
Be sure the ventilator is disconnected from the power source and both batteries have been
removed before performing any maintenance or repair. The motor is of heavy-duty ball bearing
construction. The unit is completely sealed and requires no lubrication for the life of the motor.
The ventilator blade should be specially checked for build-up of material or dirt which may cause
an imbalance. Excessive imbalance can lead to accelerated wear on motor bearings and vibration.
Remove front ventilator guard. Clean blade and inside housing with mild detergent and water. Do
not use abrasives, sharp instruments or caustic solvents that may scratch or damage the fan
blade.

POSITIVE PRESSURE VENTILATOR
8
V18-BL PPV User Guide Revised 9-2019
8. Warranty
Milwaukee products carry a separate 3-year limited warranty for the compatible battery packs, chargers and ODM battery adapter. For more
information, contact them at www.milwaukeetool.com or 1-800-729-3878.
Super Vacuum Manufacturing Company warrants that the equipment is free from defects in materials and workmanship when used and
operated for a period of five years, excluding the motor which has a 3-year warranty. The responsibility of Super Vacuum Manufacturing
Company under this limited warranty is limited to the repair and replacement of any parts which are found defective and which are returned
to Super Vacuum Manufacturing Company at 3842 Redman Dr, Fort Collins, CO 80524 with transportation charges prepaid (C.O.D. shipments
will not be accepted).
Prior to returning defective parts to SUPER VACUUM MANUFACTURING COMPANY, the original purchaser shall make a claim in writing to
SUPER VACUUM MANUFACTURING COMPANY at the above address indicating the model number and type of defect. No parts or
equipment will be received by SUPER VACUUM MANUFACTURING COMPANY for repair or replacement under this warranty without
specific written authority from it in advance.
Any parts damaged by improper installation, overloading, abuse or accident of any type or cause are not covered by this warranty.
All equipment manufactured by us is pre-run and tested before leaving our plant, and is shipped in good working order and condition. We
therefore extend to the original purchasers the following Limited Warranty for the period of five years from the original date of purchase:
1. This warranty does not apply to defects caused by accident, misuse, neglect, or wear and tear, nor can we be held responsible for
incidental and consequential expense and loss, nor does this warranty apply to equipment where alterations have been executed
without our knowledge or consent. These conditions are readily discernible when the equipment is returned to us for inspection.
2. On all component parts not manufactured by SUPER VACUUM MANUFACTURING COMPANY, their warranty is to the extent that the
manufacturer of such component warrants them to SUPER VACUUM MANUFACTURING COMPANY, if at all. Look in your local
business phone directory for the nearest repair station for the brand of parts you have or write to us for the address.
3. If equipment received is found to have been damaged in transit, a claim should be made against the carrier within three days, as we
assume no responsibility for such damage.
4. Any service other than our Authorized Service voids this warranty.
5. This warranty is in lieu of and is intended to exclude all other warranties, express or implied, oral or written, including any warranties of
MERCHANTABILITY or FITNESS for a particular purpose.

POSITIVE PRESSURE VENTILATOR
9
V18-BL PPV User Guide Revised 9-2019
9. Contact Information
For parts or service information, contact:
Super Vacuum Manufacturing Company, Inc.
3842 Redman Dr.
Fort Collins, CO 80524
Phone: [phone]
970-297-7100
Fax: [phone]
Email : [e-mail]
Internet: www.supervac.com

10
V18-BL PPV User Guide Revised 9-2019
POSITIVE PRESSURE VENTILATOR
ITEM PART NUMBER QTY DESCRIPTION
1 FRAME, V18-BL 1 FRAME, WLDMNT V18-BL
2 V18-
BL_Power_Supply_
Box 1 BOX, POWER SUPPLY, V18-BL (OPTIONAL)
3 033-10874 10 NUTSERT, TSN RIBBED, 10-24 (OPTIONAL)
4 005-15355 1 POWER SUPPLY, 750W, 24V, V18-BL
5 019-20268 1 COVER, POWER SUPPLY, V18-BD (OPTIONAL)
6 032-10096 3 SCREW,SHCS,SHCS M4x0.7x6
7 065-12852 3 STRAIN RELIEF,DOMED,SCR .24-.47,1/2 NPT,BLACK
8 065-12856 2 LOCKNUT,NYLON,1/2 NPT,BLACK
9 032-10757 4 SCREW,PHP,10-24 UNCx0.75
10 024-13473 4 FEET RUBBER CONE SHAPE VBM-4002
11 012-14196 2 INSERT, 3/8-16, TUBE, V-BD AXLE MOUNT
12 019-20253 1 TUBE, WHEEL SUPPORT, V18-BD
13 008-13804 2 WHEEL, V18-BD, 6 INCH
14 032-14564 2 SCREW,BHSH,3/8-16x2-1/2,SS
15 005-10256 10 PLUG, 1.25, TUBE END ROUND, VALOR
16 019-20266 1 COVER, CONTROLLER BOX, V18-BD
17 021-10514 1 CONTROLLER, HOAG, 18V / 36V DC MOTOR
18 065-00920 1 SHORE PLUG, V18-BD
19 032-10101 4 SCREW,PHP,8-32 UNCx0.5
20 034-10963 14 SCREW,PHP,10-24 UNCx0.5
21 005-10269 1 BUSHING, ROTATION, V18-BD
22 005-10271 2 GROMMET,PUSH-IN,0.75 ID,1.125 OD,0.0938 GROOVE
23 005-13563 1 LIGHT, LED, V18-BD
24 005-10270 1 WASHER, RUBBER, ROTATION, V18-BD
25 019-20276 1 SHROUD, V18-BD
26 012-15393 1 STREAMSHAPER GUARD FOR 18" PPV FAN
27 025-16020 1 DECAL, SHROUD, CENTER, V18,V16-BD
28 008-10193 1 KEYSTOCK,SHAFT,BLADE,718, V-18
29 003-15320 1 BUSHING,BLADE, V18-BD
30 032-10743 2 SCREW,HH,1/4-20x3/4,SS
31 021-10523 1 MOTOR,1 HP TEAO,48VDC, V18-BD
32 032-10119 4 SCREW,HH,M5x0.8x12,SS
33 021-10524 1 COVER, MOTOR, V18-BD
34 032-10118 1 SCREW,PPH,M3 X 0.5 x 8 mm
35 034-11073 1 NUT,NYLOCK, 3/8-16 UNC,SS
36 005-10266 1 HANDLE, TENSION, V18-BD
37 HANDLE, V18-BL 1 HANDLE, V18-BL, WLDMNT
38 Milwaukee_Battery_
Mount_Spacer
3
MILWAUKEE_BATTERY_MOUNT_SPACER
39 Milwaukee_Battery_
Mount_Lower
4
MILWAUKEE_BATTERY_MOUNT_LOWER
40 005-16103 8 ADAPTER, MILWAUKEE, ODM, V18-BL
41 032-10121 8 SCREW,FHPMS,4-40 UNC x 5/16 in,SS
42 032-10122 4 SCREW,FHPMS,4-40 UNC x 3/4 in,SS
43 4-40_Nut_Steel 2
44 4-40_Nut_Plastic 2
45 032-10110 4 SCREW,FHPMS,5/16-18 UNC x 7/8 in,SS
46 032-10789 4 NUT,NYLOCK, 5/16-18 UNC,SS
47 005-10255 4 T-HANDLE, PLUNGER, VALOR
48 032-10123 6 NUT, 4-40, ZINC
49 032-10695 2 NUT,MS,HEX2,8-32UNC,SS
50 STD HARDWARE-
FHMS-66
4
SCREW,FHPMS,8-32 UNC x 3/4 in,SS
51 065-00923 2 POTENTIOMETER, V18-BD
52 005-10267 2 KNOB, POTENTIOMETER, V18-BD
53 V18-
BL_Wiring_Plate
8
WIRING COVER PLATE, V18-BL
54 032-10754 8 WASHER,LOCK,SPRING,REGULAR, 1/4", SS
55 STD HARDWARE-28 22 WASHER,LOCK,SPRING,REGULAR, #10, SS
56 005-16100 1 BATTERY, MILWAUKEE, 12AH, V18-BL
57 005-13562 1 SWITCH, MOMENTARY, RGB, V18-BD
58 005-13564 1 SWITCH, LATCHING, V18-BD
59 025-16018 1 DECAL, SHROUD, CHEVRON, V18-BD
60 025-16016 2 DECAL, TOP, V18-BD
61 025-16017 4 DECAL, SERIAL NUMBER, V18-BD
62 025-16019 3 DECAL, SIDE, V18, V16-BD
63 003-15320 2 BLADE, PLASTIC, 30DEG, V18-BD (ALUMINUM BLADE AVAILABLE)
10. Parts List

11
V18-BL PPV User Guide Revised 9-2019
POSITIVE PRESSURE VENTILATOR
11. Exploded View