Superio SUP-BB-HDBT70-KIT User manual

4K/60Hz Super Slim HDBaseT Extender Kit
SUP-BB-HDBT70-KIT
USER MANUAL

1
Important Safety Information
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Do not use this product near water. Keep away from wet places, such as: spas, pools,
sinks, laundries, wet basements, etc.
4. When cleaning, unplug the unit and wipe with a dry cloth. Do not use damp cloths,
cleaning fluids, or aerosols which may result in electric shock, fire, or unit damage.
5. Operate this product using only the included power supply and/or power cable. Use of an
unapproved power implement may impair performance, damage the product, or cause
fires.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
7. Do not install or place this product near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that produce heat.
8. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the product.
9. Only use attachments/accessories specified by AV Access to avoid fire, shock, or other
hazards.
10. To reduce the risk of electric shock and/or damage to this product, never handle or touch
this unit or power cord if your hands are wet or damp. Do not expose this product to rain
or moisture.
11. Unplug this product during lightning storms or when unused for long periods of time.
12. Never open, remove unit panels, or make any adjustments not described in this manual.
Attempting to do so could result in electric shock, damage to the unit, or other hazards.

2
Contents
Important Safety Information............................................................................ 1
Introduction ......................................................................................................3
Features ...................................................................................................3
Package Contents ....................................................................................3
Panel Description.............................................................................................4
Transmitter................................................................................................4
Receiver ...................................................................................................5
Specifications...................................................................................................6
Installation and Wiring...................................................................................... 7
Installation.................................................................................................7
Wiring ....................................................................................................... 7
RS232 Operation ........................................................................................... 10

3
Introduction
SUP-BB-HDBT70-KIT is a slim transmitter receiver pair, which can extend
HDMI 1080P@60Hz signals up to 70m/230ft and 4K@60Hz (chroma
sub-sampling 4:2:0 8-bit only) signals up to 40m/130ft via a single Cat 6a/7
cable. SUP-BB-HDBT70-KIT features bi-directional PoC. It also supports
bi-directional IR and RS232 pass-through.
Features
Supports resolutions up to 4K@60Hz 4:2:0 8bit and HDCP 2.2.
Over a Cat 6a/7 cable, extends 4K@60Hz 4:2:0 8bit up to 40m/130ft and
1080P up to 70m/230ft.
Over a Cat 5e/6 cable, extends 4K@60Hz 4:2:0 8bit up to 35m/115ft and
1080P up to 60m/200ft.
Bi-directional PoC, one power adapter at either transmitter or receiver
side can power both units.
Supports bi-directional IR and RS232 pass-through.
Package Contents
1 x SUP-BB-HDBT70 Transmitter
1 x SUP-BB-HDBT70 Receiver
1 x DC 18V Power Cord with EU Pins
1 x IR Emitter
1 x Broadband IR Receiver (30-50kHz)
2 x Phoenix Connector (3 Pins, 3.5mm)
4 x Mounting Brackets (with Screws)

4
Panel Description
Transmitter
Front Panel
1 2 3 4
No.
Name
Description
1 POWER LED •On: The device is powered on.
•
Off
: The device is powered off.
2 STATUS LED •On: The device is working properly.
•
Off: The device is not working properly.
3 HDCP LED
•On: HDCP protected content is being transmitted.
•Blinking: Non-HDCP protected content is being
transmitted.
•
Off:
No content is being transmitted.
4 LINK LED •On: HDBT link is normal.
•
Blinking/Off: No HDBT link or link error.
Rear Panel
1 2 3 4 5 6
No.
Name
Description
1
DC 18V
Connect to the DC 18V power cord provided.
2 HDBT OUT Connect to the receiver via a Cat 5e/6/7 cable.
3
IR IN
Connect to the IR receiver provided.
4
IR OUT
Connect to the IR emitter provided.
5
RS232
For RS232 pass-through.
6
HDMI IN
Connect to an HDMI source.

5
Receiver
Front Panel
1 2 3 4
No.
Name
Description
1 POWER LED •On: The device is powered on.
•
Off: The device is powered off.
2 STATUS LED •On: The device is working properly.
•
Off:
The device is not working properly.
3 HDCP LED
•On: HDCP protected content is being transmitted.
•Blinking: Non-HDCP protected content is being
transmitted.
•
Off: No content is being transmitted.
4 LINK LED •On: HDBT link is normal.
•
Blinking/Off:
No HDBT link or link error.
Rear Panel
1 2 3 4 5 6
No.
Name
Description
1
DC 18V
Connect to the DC 18V power cord provided.
2
HDBT OUT
Connect to the transmitter via a Cat 5e/6/7 cable.
3
IR IN
Connect to the IR receiver provided.
4
IR OUT
Connect to the IR emitter provided.
5
RS232
For RS232 pass-through.
6
HDMI IN
Connect to an HDMI source.

6
Specifications
Technical
Input/Output Port
Transmitter:
1 x HDMI IN; 1 x HDBT OUT; 1 x RS232; 1 x DC 18V IN
Receiver:
1 x HDMI OUT; 1 x HDBT IN; 1 x RS232; 1 x DC 18V IN
Input/Output Signal Type
HDMI with 4K@60Hz 4:2:0, HDCP 2.2
Input/Output Resolution
Supported
Up to 4096x2160@60Hz, including
4K@60Hz/4K@30Hz/1080P/1080i/720P
Note: 4096x2160/3840x2160@50/60Hz is based on chroma
sub-sampling 4:2:0 8-bit only.
Audio Format Supported Supports multichannel audio up to PCM 7.1, Dolby True HD,
DTS HD Master Audio, Dolby Atmos and DTS:X
Maximum Data Rate
10.2Gbps
Maximum Pixel Clock
340MHz
Control Method
IR, RS232
General
Operating Temperature
0°C to 45°C (32°F to 113°F)
Storage Temperature
-20°C to 70°C (-4°F to 158°F)
Humidity
10% to 90%, non-condensing
ESD Protection
Human-body Model:
±8kV (Air-gap discharge)/
±4kV (Contact discharge)
Power Supply
DC 18V 1A
Power Consumption
8.88W (Pair, PoC) (Max)
Device Dimension
(W x H x D)
108.8mm x 15mm x 64.2mm (4.3" x 0.6’’ x 2.5’’) (mounting
brackets not included) each for TX/RX
Net Weight
0.18kg/0.40lb each for TX/RX
Transmission Distance
Note: Straight-through category cable of T568B standard is recommended.
Cable Type Range Supported Video
Cat 5e/6
60m/200ft
Up to 1080P@60Hz, 36bpp
Cat 6a/7 70m/230ft
Cat 5e/6
35m/115ft
1080P@60Hz, 48bpp
4K@60Hz, 4:2:0, 24bpp
Cat 6a/7 40m/130ft

7
Installation and Wiring
Installation
CAUTION:Before installation, please ensure the device is disconnected from
the power source.
Steps to install the switcher on a suitable location:
1. Attach the installation bracket to the enclosure using the screws provided
in the package separately.
2. The bracket is attached to the enclosure as shown.
3. Repeat steps 1-2 for the other side of the transmitter.
4. Install the unit in the mounting rack using the screws (provided by
others).
5. Repeat steps 1-4 to install the receiver.
Wiring
WARNING:Before wiring, ensure all units are DISCONNECTED from power.
Otherwise, circuitry damage or physical injury may be caused.
Steps for device wiring:
1. Connect video source
Connect an HDMI source (such as PC, Blu-ray player, Apple TV, 4K
media player, etc) to the HDMI IN port of transmitter.

8
2. Connect HDMI OUT
Connect an HDMI display device (such as TV, projector, LED/LCD
display) to the HDMI OUT port of receiver.
3. Connect HDBT OUT
Connect HDBT OUT of the transmitter to HDBT IN of the receiver with a
Cat 5e/6/7 cable.
4. Connect for additional control options:
•RS232 pass-through: Connect a RS232 master device (or slave
device) to RS232 port of the transmitter, and a RS232 slave device
(or master device) to RS232 port of the remote receiver for
bi-directional RS232 pass-through.
•IR pass-through: Connect an IR emitter (or IR receiver) to the IR
connector of the transmitter, and an IR receiver (or IR emitter) to IR
connector of the receiver for bi-directional IR pass-through.
5. Connect the DC 18V power cord provided to the transmitter.
6. Power on all attached devices.
When all is set, check if all LED indicators on switcher are normal to ensure
installation is successful. For LED indication, please refer to Panel
Description section.
See below application diagram:

9
Transmitter
Receiver
Blu-ray PlayerDisplay Remote
IR Emitter1
IR Receiver2 HDMI IN
Display
Source Remote
IR Receiver1
IR Emitter2
HDMI OUT
Cat x

10
RS232 Operation
RS232 ports can be used for bi-directional RS232 signal pass-through
between the transmitter and receiver.
Transmitter
Receiver
Cat x
RS232 Device
RS232 Device
G
RX
TX
GND
TX
RX
RS232 Port Connected RS232 Device Pins

Version: V1.0.1
www.superio.com
[e-mail]
SWEDEN