Directed Electronics Xpresskit Series User manual

XL202
Installation Guide
COMPATIBILITY
REQUIREMENT SPECIFICATIONS
+
XK Modules
Range Extender*
* Vehicles equipped with factory remote starter only
The RFTD feature of the
CANMAX400 must be turned on to
have full two-way communication.
The power ( ) must be applied
last to the XK module.
12V
†CANMAX400 is not only a range extender, it is also a standalone remote starter.
TECHNICAL SUPPORT / INFORMATION
web resources:
www.xpresskit.com
www.xpressvip.com
www.directechs.com
tm
Update Alert
Firmware updates are posted to the web on a regular basis. It is important that you check
for firmware and/or install guide updates prior to the installation of this product.
XL202
Remote Starter Standalone
Note: See XpressKit.com for vehicle application guide.
+
XL202
DLPKKICH3
or XK09
†
or CANMAX400
+
XL202
†
CANMAX400
To proceed with the installation of the
XL202 RFTD with Astro firmware you need:
XL202RFTDmodule.
D2Dharness.
AstroStart RF kit, which includes a
and a receiver antenna.
?
?
?remote
* This image is for example purposes only. Your remote may
be a different model.
*
Page 1
Rev.: 20091124
© 2009 Directed Electronics. All rights reserved.
MODEL: XL202
FIRMWARE: RFTDAF

HOW TO PROGRAM A REMOTE INTO XL202
3Press and hold the programming button of the XL202 to enter in programming mode.
XL202
PRESS & HOLD
PROGRAMMING
BUTTON
5When programming is finished, release programming button on the XL202.
XL202
RELEASE
PROGRAMING
BUTTON
4
1Refer to the D2D installation instructions for the module to make all the necessary connections and ensure power is supplied to
the XL202.
2Antenna
XL202
1. Connect the antenna to module with the antenna harness (number 1 in the diagram).
2. Connect the module to the 4-pin connector of the using the D2D harness (number 2 in the diagram).
3. Connect wires to the vehicle according to the firmware install guide.
XL202 XL202
HOW TO CONNECT
Antenna
HARNESS #2 HARNESS #1
D2D Antenna
LED
side view
XL202
Page 2
XK modules: The power ( ) must be applied last to the XK module.12V
CANMAX400: The RFTD feature must be turned on to have full two-way communication.
Plug the module and the antenna in the XL202.
See page 3 for more information on how to switch between modes.
Press one of the remote buttons while holding the programming button to program the remote
into the XL202; the LED flashes once.
- Unlock: driver priority unlock.
If the Unlock button is pressed once, the driver door is unlocked; if pressed twice however, all
doors are unlocked.
- Any other button: unlock all.
* To program extra remotes, repeat steps 3 & 4 for each remote.
(A maximum of four (4) remotes can be programmed in an XL202.)
PRESS ONE OF
THE BUTTONS
ON THE REMOTE
Important Note
There are 4 memory slots. Every time you program a new remote, you access the next memory slot, empty or not.
After the 4th one is reached, it will go back to the 1st one, and so on.
Each remote has its own unlock setting, once decoded/learned. If for some reason, the same remote is programmed in slot #1 and #3,
slot #1 is decoded first so the associated function for the unlock feature will be from slot #1, not from #3. It is preferable to erase all
remotes if you are unsure.
The feature behavior may vary depending on which firmware you are using.
Rev.: 20091124
© 2009 Directed Electronics. All rights reserved.
MODEL: XL202
FIRMWARE: RFTDAF

SWITCHING BETWEEN MODES
1. Remove power to the XL202 module.
2. Press and hold the Programming button.
3. Reconnect the XL202 module, while still holding the Programming button. The LED turns on solid.
4. Release the button, then press and hold it once again. The LED turns off/on following the sequence.
If you hold the button longer than 5 seconds, it will erase all the memory content.*
5. After 2 seconds, the XL202 turns off the LED and switches mode. You can release the button and watch the LED:
- Mode 1
1x slow LED flash = LCD (XRT) remotes
- Mode 2
2x slow LED flash = Non-LCD remotes
Once the mode is changed, it erases all memory content and reverts to normal operation by itself. No more manipulation is
required, other than learning the remote.
* Erasing all remotes from memory:
1. Remove power to the XL202 module.
2. Press and hold the Programming button, while reconnecting the power to the XL202 module.
3. Keep holding the Programming button. The LED will stay on for 5 seconds, then it will start to flash quickly.
4. You can now release the button.
Once the module stops flashing, the memory content has been erased. The next step is to program all desired remotes.
Page 3
Rev.: 20091124
© 2009 Directed Electronics. All rights reserved.
MODEL: XL202
FIRMWARE: RFTDAF

Limited One-year Consumer Warranty
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics.
(“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote
start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the
following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED,
postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name,
address,telephonenumber,theauthorizedlicenseddealer’snameandcompleteproductandPartdescription.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended
purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not
arisingoutofdefectinmaterialsorconstruction.
TOTHE MAXIMUM EXTENTALLOWED BY LAW,ALL WARRANTIES, INCLUDING BUT NOTLIMITED TO EXPRESS WARRANTY,
IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSEAND WARRANTY OF NON
INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR
AUTHORIZESANYPERSONORENTITYTOASSUMEFORITANYDUTY,OBLIGATIONORLIABILITYINCONNECTIONWITHITS
PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD
PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OFACLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS
SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE
LAWS AND APPLICABLE FEDERAL LAWS SHALLAPPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER
ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE
PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FORANY DAMAGES WHATSOEVER, INCLUDING BUT NOT
LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE,
THEMANUFACTURERDOESOFFERALIMITED WARRANTYTOREPLACE OR REPAIRATDIRECTED’SOPTIONTHE PARTAS
DESCRIBEDABOVE.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or
consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to
State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or
obligation in connection with this Part.920-0007 07-06
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list
uponcompletionofcompatibilitytesting.Visitwebsiteforlatestvehicleapplicationguide. DISCLAIMER:Undernocircumstancesshall
the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages
sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any
representativeoranyotherindividualtoassumeobligationorliabilityinrelationtotheinterfacekit/databusinterfacepart(s)otherthan
its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential
damagessustainedin connectionwiththisproductand neitherassumes norauthorizesanyrepresentativeor otherpersontoassume
foritanyobligationorliabilityotherthanthereplacementofthisproductonly.
PROTECTED BY U.S. PATENTS:5,719,551;6,011,460B1*;6,243,004B1; 6,249,216B1; 6,275,147B1;6,297,731B1; 6,346,876 B1;
6,392,534B1; 6,529,124B2; 6,696,927B2; 6,756,885B1; 6,756,886B2; 6,771,167B1; 6,812,829B1; 6,924,750B1; 7,010,402 B1;
7,015,830B1; 7,031,826B1; 7,046,126B1; 7,061,137B1; 7,068,153B1; 7,205,679B1; CDN. PATENT:2,320,248; 2 , 4 1 4 , 9 9 1 ;
2,415,011;2,415,023;2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089 EUROPEAN PATENT:1,053,128 PAT.
PENDING:2,291,306; MADE IN CANADA
Page 4
Rev.: 20091124
© 2009 Directed Electronics. All rights reserved.
MODEL: XL202
FIRMWARE: RFTDAF