Supermicro X10DRD-L User manual

SUPERMICR R
ContaCt InformatIon
MNL-1712-QRG-10a
• Website: www.supermicro.com
• General Information: [email protected]
• Tech Support: [email protected]
• Phone: [phone], Fax: [phone]
© 2016 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
X10DrD-L/Lt/I/It/Int
QuICk referenCe GuIDe rev. 1.0a
• One (1) iPASS to 4-SATA cable
(CBL-0097L-03) (for X10DRD-i/iT/iNT)
• One (1) Quick Reference Guide
(MNL-1712-QRG)
for your system to work properLy, pLease DownLoaD approprIate
DrIvers/ImaGes/user'smanuaL from the LInks beLow:
• Manuals: http://www.supermicro.com/support/manuals/
• Drivers & Utilities: ftp://ftp.supermicro.com/
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
paCkaGe Contents
• One (1) Supermicro Motherboard
• Four (4) SATA Cables (CBL-0044L)
• One (1) I/O shield (MCP-260-
00042-0N)
This motherboard supports up to 1024 GB of Load Reduced (LRDIMM) or 256 GB
of Registered (RDIMM) DDR4 (288-pin) ECC 2400/2133/1866/1600 MHz modules
in eight slots. Memory speed support is dependent on the CPUs installed in the
motherboard. For the latest memory updates, please refer to our website at http://
www.supermicro.com/products/motherboard.
Dual Intel®E5-2600v3/v4 Series processors (Socket R3-LGA 2011); each processor
supports dual full-width Intel QuickPath Interconnect (QPI) links (of up to 9.6 GT/s
one direction per QPI)
Notes: 1. The X10DRD-LT/i/iT/iNT supports CPU Thermal Design Power
(TDP) of up to 145W, and X10DRD-L supports TDP of up to 120W.
2. Please install both CPUs for full access to onboard PCI-E slots, DIMM
slots, and controllers. Refer to the block diagram on page 1-10 in the user's
manual to determine which slots or devices may be affected. Please populate
CPU socket 1 rst.
Connectors
Jumper Description Default Setting
JBT1 Clear CMOS See Chapter 2
JI2C1/JI2C2 SMB to PCI-E Slots Pins 2-3 (Disabled)
JPB1 BMC Enable Pins 1-2 (Enabled)
JPG1 VGA Enable Pins 1-2 (Enabled)
JPL1 Gigabit LAN 1/2 Enable (X10DRD-L/i) Pins 1-2 (Enabled)
JPL1 10G_LAN 1/2 Enable (X10DRD-LT/iT/iNT) Pins 1-2 (Enabled)
JPME2 Manufacture (ME) Mode Select Pins 1-2 (Normal)
JWD1 Watch Dog Timer Enable Pins 1-2 (Reset)
Connectors Description
JBAT1 (Battery) Onboard CMOS battery (See Chpt. 3 for Used Battery Disposal)
COM1/COM2 Backplane COM Port1/Front accessible COM2 header
FAN 1- 8 CPU/system fan headers (FAN1-FAN8)
IPMI_LAN IPMI_dedicated LAN support by the Aspeed controller
JF1 Front panel control header
JL1 Chassis intrusion header
JPI2C1 Power supply SMBbus I2C header
JPWR1 24-pin ATX main power connector (See Warning on Pg. 1-6)
JPWR2/JPWR3 12V 8-pin power connectors (See Warning on Pg. 1-6.)
JSTBY1 Standby power connector
JTPM1 TPM (Trusted Platform Module)/Port 80 header
P1-NVME0/1 NVM Express PCI-E 3.0 x4 ports (by internal mini-SAS HD con-
nector) (for X10DRD-iNT only)
I-SATA 0-5 SATA 3.0 connectors supported by Intel PCH (I-SATA 0-5), (I-
SATA4/I-SATA5: can be used as Supermicro SuperDOMs [Devic-
es-on-Module] with built-in power connectors)
S-SATA0-3 SATA 3.0 connections 0-3 supported by Intel SCU (for X10DRD-i/
iT/iNT only)
LAN1 10G Ethernet LAN Port 1 (X10DRD-LT/iT/iNT)
Gigabit Ethernet LAN Port1 (X10DRD-L/i)
LAN2 10G Ethernet LAN Port 2 (X10DRD-LT/iT/iNT)
Gigabit Ethernet LAN Port2 (X10DRD-L/i)
(CPU1)Slot4 PCI-Express 3.0 x8 slot from CPU1 (for X10DRD-i/iT/iNT)
(CPU1)Slot5 PCI-Express 3.0 x8 slot from CPU1 (for X10DRD-i/iT/iNT)
(CPU1)Slot6 PCI-Express 3.0 x8 slot from CPU1
(CPU2)Slot7 PCI-Express 3.0 x8 slot from CPU2 (for X10DRD-i/iT/iNT) (CPU2
is required)
SP1 Internal speaker/buzzer
UID-SW (JUIDB1) UID (Unit Identication) switch
(BP) USB 0/1 (2.0) Backpanel USB 2.0 ports 0/1
(BP) USB 2/3 (2.0) Backpanel USB 2.0 connections (USB 2/3) header
(FP) USB 4/5 (2.0) Front-accessible USB 2.0 ports 4/5
(FP) USB 6 (2.0) Front-accessible Type A 2.0 connector (USB6)
VGA Backpanel VGA port
LED Description State Status
LED1 Rear UID LED Blue: On Unit Identied
LEDM1 BMC Heartbeat LED Green: Blinking BMC Normal
CLOSE 1st
OPEN 1st
SAN MAC
BAR CODE
MAC CODE
IPMI CODE
JBAT1
JUSBRJ45
S-SATA0-3
X10DRD-L(T)/i(T)/iNT
REV:1.00
BIOS
LICENSE
I-SATA5
I-SATA4
I-SATA0
I-SATA1I-SATA3
I-SATA2
JSTBY1
JL1
FAN3
FAN7
FAN8
FAN5
FAN6
I-SGPIO2
I-SGPIO1
JTPM1
JPWR1
JPWR3
JF1
JPI2C1
JPL1
JVRM_I2C2
JVRM_I2C1
JPME2
JI2C2
JWD1
JI2C1
JPG1
LEDM1
LED1
JUIDB1
SP1
CPU1 SLOT4 PCI-E 3.0 X8
P1_NVME0
P1_NVME1
P2-DIMMG1
P2-DIMMH1
P1-DIMMC1
P1-DIMMB1
P1-DIMMD1
P1-DIMMA1
IPMI_LAN
COM1
COM2
USB4/5
CPU1 SLOT5 PCI-E 3.0 X8
CPU1
CPU1 SLOT6 PCI-E 3.0 X8
CPU2 SLOT7 PCI-E 3.0 X8
VGA
LAN1
USB2/3
USB0/1
USB6
JPWR2
FAN2 FAN1
FAN4
P2-DIMMF1
P2-DIMME1
JPB1
CPU2
PCH
BMC
AST2400
Intel LAN
CTRL
(For -iNT only)
BIOS
CLOSE 1st
OPEN 1st
JIPMB1
LAN2
(For -i(T)/iNT only)
JBT1
12
Ground
19 20
NMI
X
X
FP PWRLED
3.3 V
HDD LED
UID Switch
NIC1 Link LED
NIC1 Activity LED
NIC2 Link LED
NIC2 Activity LED
UID LED OH/Fan Fail/
PWR Fail LED)
Power Fail LED
3.3V
Reset Button
Power Button Ground
Ground
Speed (MT/s)
Voltage (V)
Jumpers
Motherboard Layout and Features Jumpers and Connectors
Populating RDIMM/LRDIMM ECC Memory Modules
Back Panel I/O Connectors
Memory Support
CPU Installation
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as the drawings shown in this guide.
Note: Refer to Chapter 1 of the user's manual for detailed information on jumpers, connectors, and LED
indicators.
Note: Refer to Chapter 2 of the user's manual for detailed information on memory support and CPU/
motherboard installation instructions.
= mounting hole
Heatsink Installation Front Panel Control (JF1)
CPU Support
Release Tabs
2
3
4
5
6
7
8
9
10
1
LED Indicators
Notches
OPEN1st
Screw#1
Screw#2
Mounting Holes
Direction of the airow
Note: For optimal airow, please follow your
chassis airow direction to correctly install the
CPU heatsink.
Socket Keys
CPU Keys
OPEN 1st
OPEN 1st
1. COM Port 1
2. Back Panel USB 2.0 Port 0
3. Back Panel USB 2.0 Port 1
4. IPMI-Dedicated LAN
5. Back Panel USB 2.0 Port 2
6. Back Panel USB 2.0 Port 3
7. 10GbE LAN Port 1 (X10DRD-LT/iT/iNT)
Gigabit LAN Port 1 (X10DRD-L/i)
8. 10GbE LAN Port 2 (X10DRD-LT/iT/iNT)
Gigabit LAN Port 2 (X10DRD-L/i)
9. Back Panel VGA (Blue)
10. UID Button/UID LED
Populating RDIMM/LRDIMM
DDR4 Memory Modules
for the E5-2600v3-based
Motherboard
Populating RDIMM/LRDIMM
DDR4 Memory Modules
for the E5-2600v4-based
Motherboard
Type
Ranks Per
DIMM
and
Data
Width
DIMM Capacity
(GB)
Speed (MT/s);
Voltage (V);
Slot Per Channel
(SPC) and DIMM Per
Channel (DPC)
1 Slot Per Channel
1DPC
4Gb
8Gb
1.2V
RDIMM
SRx4
8GB
16GB
2133
RDIMM
SRx8 4GB 8GB 2133
RDIMM
DRx8
8GB
16GB
2133
RDIMM
DRx4 16GB 32GB 2133
LRDIMM
QRx4
32GB
64GB
2133
LRDIMM
3DS
†
8Rx4 64GB 128GB 2133
Type
Ranks Per
DIMM
and
Data
Width
DIMM Capacity
(GB)
Speed (MT/s);
Voltage (V);
Slot Per Channel
(SPC) and DIMM Per
Channel (DPC)
1 Slot Per Channel
1DPC
4Gb 8Gb 1.2V
RDIMM SRx4 8GB 16GB 2400
RDIMM SRx8 4GB 8GB 2400
RDIMM DRx8 8GB 16GB 2400
RDIMM DRx4 16GB 32GB 2400
LRDIMM QRx4 32GB 64GB 2400
LRDIMM
3DS 8Rx4 64GB 128GB 2400