SUPERMICR R
ContaCt InformatIon
MNL-1553-QRG-10a
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
© 2014 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written
consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
PaCkage Contents
X10sBa(-L)
QuICk referenCe guIde 1.0a
• One (1) Supermicro Motherboard
• Six (6) SATA Cables (2 cables for the -L model)
• One (1) I/O Shield
• One (1) Quick Reference Guide
LED Indicators
Connectors
DIMM Memory Installation
Back Panel I/O Connectors
Motherboard Layout and Features
Jumpers
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide. Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators.
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
= mounting hole
Front Panel Control (JF1)
X10SBA(-L)
Rev. 1.01
JSMB1
J5
JBT1
BT2
M-SATA0M-SATA1
M-SATA2
M-SATA3
JP1
LAN1LAN2
JDIMM2
PJ1
JF1
JTPM1
JOH1
JSPDIF_OUT
JPUSB1
JPAC1
JD1
VGA
FAN1
FAN2
I-SATA1
COM4
COM2
SP1
JSD1
JDIMM1
JPW1
SMBUS1
SLOT1 PCI-E 2.0 X2 (IN X8)
USB4/5
USB6
AUDIO FP
SO-DIMM2 (1.35V only)
USB1(2.0)
USB0(3.0)
CPU
(Install first)SO-DIMM1(1.35V only)
Non-ECC DDR3 Required
eDP
(Embedded Display Port)
HDMI/DP
COM3
BIOS
BAR CODE
J1
(for mini-PCI-E only)
(for M-SATA only)
J2
COM1
(for X10SBA only)
(for X10SBA only)
(for X10SBA only)
(for X10SBA)
LED1
LED5
USB2/3
I-SATA0
LED Description Color/State Status
LED1 Main Power LED Green: On Power On
LED5 Standby Power LED Green: On AC On
Jumpers/Connectors/LED Indicators Memory Support
The X10SBA/X10SBA-L supports up to 8 GB of DDR3L (1.35, Low Voltage) Non-
ECC SO-DIMM of up to 1333 MHz in two horizontal sockets. Populating these DIMM
slots with a pair of memory modules of the same type and same size will result in
interleaved memory, which will improve memory performance.
Insert the desired number of SO-DIMMs into the memory slots, starting with SO-
DIMM1, then SO-DIMM2.
Socket Key
Receptive Point on
the Module
SO-DIMM Memory
Module
Memory Module Socket
A. HDMI E. LAN1
B. DisplayPort F. LAN 2
C. USB0 (3.0) G. VGA
D. USB1 (2.0)
E
A
B
C
OH/Fan Fail/PWR Fail
LED Cathode
1
NIC1 Link LED
Reset Button
2
HDD LED
PWR LED
Reset
PWR
3.3V
3.3V Stby
3.3V Stby
Ground
Ground
1920
X
Ground
X
3.3V Stby
3.3 V
Power Fail LED
NIC2 Link LED
X
1. Align the receptive point on the bottom of the SO-DIMM module against
the key on the memory socket. Note the notches on the side of the SO-
DIMM module and those on the socket to avoid causing damage.
2. Line up the bottom of the SO-DIMM memory module with the edge of the
horizontal socket.
3. Once they are lined up, push the memory module into the memory socket
until the module is securely seated in the socket.
DIMM Memory Removal
1. Use your thumbs to gently push the side clips on both ends of the socket
away from the SO-DIMM module to release it from the locked position.
Socket Side Clip
Socket Side Clip
2. Once the memory module is loosened from the socket, pull it upwards and
outwards to remove it from the socket.
JBT1 CMOS Clear Open: Normal Operation (Default)
Short: Clear CMOS
JPAC1 Audio Enable Pins 1-2 (Enabled)
JPME2 Intel Manufacturer Mode Select Pins 1-2 (Normal)
JPUSB1 USB Wake-Up Enable Pins 1-2 (Enabled)
Connector Description
Audio FP Front Panel Audio Header
Battery Onboard Battery (BT2)
COM1-COM4 COM1/COM2/COM3/COM4 Headers
FAN1/FAN2 System Fan Headers
HDMI/DP (Backpanel) HDMI/DisplayPort
J1 mini-PCI-E Slot for a mini-PCI-E Card (Not available on the -L model)
J2 mSATA slot MUX (Multiplexer/Switch) with I-SATA1 (Not available on the
-L model)
J4 (Slot1) PCI-E 2.0 x 2 in x8 Slot
J5 (eDP) Embedded DisplayPort (eDP)
JD1 Power LED/Speaker Header (Pins 1-3: Power LED, Pins 6-7: Internal
Buzzer, Pins 4-7: External Speaker)
JF1 Front Panel Control Header
JOH1 Overheat LED Indicator Header
JP1 General Purpose I/O Header
JPW1 24-pin ATX Power Connector (Optional Power Source)
JSD1 SATA DOM (Device_On_Module) Power Connector
JSPDIF_OUT S/PDIF (Sony/Phillips Digital Interconnect Format) Audio Output Header
JTPM1 Trusted Platform Module/Port 80 Connector
LAN1/LAN2 Gigabit (RJ45) Ports (LAN1/2)
PJ1 4-pin 12V DC Power Connector (Optional Power Source up to 144W)
I-SATA0/1 (Intel-)Serial ATA (SATA 2.0) Ports 0/1
M-SATA0/1/2/3 (Marvell 88SE9230) Serial ATA (SATA 3.0) Ports 0-3 (Not available on
the -L model)
SMBUS1 (JSMB1) 4-Pin External System Management Bus I2C Header (JSMB1) (for slave
device)
SP1 Internal Speaker/Buzzer
USB 0 Backpanel USB 3.0 Port 1
USB 1 Backpanel USB 2.0 Port 2
USB 2/3, USB 4/5 Front Accessible USB 2.0 Connections: USB 2/3 (USB 3 is available
on the -L model)
USB 4/5 (Not available on the -L model)
USB 6 Front Accessible Type A USB 2.0 Connector (Not available on the -L
model)
VGA Backpanel VGA Port
