Supermicro BPN-SAS3-743A-N4 User manual

Rev. 1.0
BPN-SAS3-743A-N4 Backplane
USER'S GUIDE

ii
BPN-SAS3-743A-N4 Backplane User's Guide
Manual Revision 1.0
Release Date: December 6, 2017
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2017 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

iii
Preface
Table of Contents
Contacting Supermicro.......................................................................................iv
Returning Merchandise for Service.....................................................................v
Chapter 1 Safety Guidelines ....................................................................1-1
1-1 ESD Safety Guidelines ................................................................................... 1-1
1-2 General Safety Guidelines .............................................................................. 1-1
1-3 An Important Note to Users ............................................................................ 1-2
1-4 Introduction to the BPN-SAS3-743A-N4 Backplane ....................................... 1-2
Chapter 2 Connectors and Pin Denitions.............................................2-1
2-1 Front Connectors ............................................................................................ 2-1
2-2 FrontConnectorPinDenitions...................................................................... 2-2
2-3 FrontJumperLocationsandPinDenitions................................................... 2-3
2-4 Rear Connectors and LED Indicators............................................................. 2-5

iv
BPN-SAS3-743A-N4 Backplane User's Guide
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacic
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone]

v
Preface
Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required be-
fore any warranty service will be rendered. You can obtain service by calling your
vendor for a Returned Merchandise Authorization (RMA) number. When returning
to the manufacturer, the RMA number should be prominently displayed on the
outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and
handling charges will be applied for all orders that must be mailed when service
is complete.
For faster service, RMA authorizations may be requested online (http://www.super-
micro.com/support/rma/).
Whenever possible, repack the backplane in the original Supermicro box, using the
original packaging materials. If these are no longer available, be sure to pack the
backplane in an anti-static bag and inside the box. Make sure that there is enough
packaging material surrounding the backplane so that it does not become damaged
during shipping.
This warranty only covers normal consumer use and does not cover damages in-
curred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
Duringthewarrantyperiod,contactyourdistributorrstforanyproductproblems.

1-1
Chapter 1: Safety Guidelines
Chapter 1
Safety Guidelines
To avoid personal injury and property damage, carefully follow all the safety steps
listed below when accessing your system or handling the components.
1-1 ESD Safety Guidelines
Electrostatic Discharge (ESD) can damage electronic components. To prevent dam-
age to your system, it is important to handle it very carefully. The following measures
are generally sucient to protect your equipment from ESD.
• Use a grounded wrist strap designed to prevent static discharge.
• Touch a grounded metal object before removing a component from the antistatic
bag.
• Handle the backplane by its edges only; do not touch its components, peripheral
chips, memory modules, or gold contacts.
• When handling chips or modules, avoid touching their pins.
• Put the card and peripherals back into their antistatic bags when not in use.
1-2 General Safety Guidelines
• Always disconnect power cables before installing or removing any components
from the computer, including the backplane.
• Disconnect the power cable before installing or removing any cables from the
backplane.
• Make sure that the backplane is securely and properly installed on the mother-
board to prevent damage to the system due to power shortage.

1-2
BPN-SAS3-743A-N4 Backplane User's Guide
1-3 An Important Note to Users
• All images and layouts shown in this user's guide are based upon the latest PCB
revision available at the time of publishing. The card you have received may or
may not look exactly the same as the graphics shown in this manual.
1-4 Introduction to the BPN-SAS3-743A-N4 Backplane
The BPN-SAS3-743A-N4 backplane has been designed to utilize the most up-
to-date technology available, providing your system with reliable, high-quality
performance.
ThismanualreectsBPN-SAS3-743A-N4Revision1.00,themostcurrentrelease
available at the time of publication. Always refer to the Supermicro Web site at
www.supermicro.com for the latest updates, compatible parts, and supported
congurations.

2-1
Chapter 2: Connectors and Pin Denitions
Chapter 2
Connectors and Pin Denitions
2-1 Front Connectors
1. Chip: CPLD
2. JTAG Connector: J16
3. NVMe Connector #3: CN3
4. NVMe Connector #2: CN2
5. NVMe Connector #1: CN1
6. NVMe Connector #0: CN0
7. SAS Port #1: JSM1
8. SAS Port #0: JSM0
9. Power Connector (4-pin) #3:
JPW3
10. Power Connector (4-pin) #2:
JPW2
11. Power Connector (4-pin) #1:
JPW1
Figure 2-1. Front Connectors
8
1
7
109 11
23 4 56

2-2
BPN-SAS3-743A-N4 Backplane User's Guide
#9. - 11. Backplane Main Power Connectors
The 4-pin connectors, designated JPW1,
JPW2, and JPW3, provide power to the
backplane. See the table on the right for
pindenitions.
2-2 Front Connector Pin Denitions
#2. JTAG Connector
The JTAG connector, designated J16, is
used for diagnostic purposes. This connec-
tor should not be used as it is for internal
testing only.
Backplane
Main Power
4-Pin Connector
Pin#Denition
1 +12V
2 and 3 Ground
4 +5V
#7. - 8. SAS Ports
The SAS ports are used to connect the
SAS or SATA drive cables CBL-SAST-0532
to an HBA card inserted in a PCIe slot on
motherboard X11DAi-N. The 2 ports are
designated JSM0, for drives at SAS #0-#3,
and JSM1, for drives at SAS #4-#7 (see
section 2-4 for SAS drive locations). Each
port is also compatible with SATA drives.
However, mixing SAS and SATA drives in
the same enclosure is not recommended.
#1. CPLD Chip
The CPLD is an enclosure management
chip that supports the SGPIO and LED
management.
#3. - 6. NVMe Connectors
The NVMe ports are used to connect the
NVMe drive cables. To congure 2 NVMe
drives, OCuLink cables CBL-SAST-0820
should be used to connect ports CN0 and
CN1 to NVMe slots 1 and 2 on motherboard
X11DAi-N. To congure 4 NVMe drives,
OCuLink cables CBL-SAST-0820 should
be used to connect all 4 ports to four corre-
sponding ports on add-on card AOC-SLG3-
4E4T in slot 3 of motherboard X11DAi-N
and connected to the motherboard's NVMe
I2C2 header with cable CBL-CDAT-0674.

2-3
Chapter 2: Connectors and Pin Denitions
2-3 Front Jumper Locations and Pin Denitions
JP8
Figure 2-2. Front Jumpers
Explanation of Jumpers
To modify the operation of the backplane,
jumpers can be used to choose between
optional settings. Jumpers create shorts
between two pins to change the function
of the connector. Pin 1 is identied with
a square solder pad on the printed circuit
board.
Note: On two pin jumpers, "Closed" means
the jumper is on and "Open" means the
jumperiso󰀨thepins.
Connector
Pins
Jumper
Setting
3 2 1
3 2 1
ACTLED
JP9

2-4
BPN-SAS3-743A-N4 Backplane User's Guide
Jumper Settings
JP8 JP9 Description
2-3 2-3 All 4 drives connected to main CPU. (default)
1-2 2-3 3 drives connected to main CPU, 1 drive connected to 2nd
CPU.
2-3 1-2 2 drives connected to main CPU, 2 drives connected to 2nd
CPU.
1-2 1-2 1 drive connected to main CPU, 3 drives connected to 2nd
CPU.
LED Test
ACTLED Description
Open For internal use only. (default)

2-5
Chapter 2: Connectors and Pin Denitions
/SAS#0 /SAS#1 /SAS#3 SAS#4 SAS#5 SAS#6 SAS#7 /SAS#2
2-4 Rear Connectors and LED Indicators
Figure 2-4. Rear Connectors & LED Indicators
SAS/SATA/NVMe Connectors and LED Indicators
Rear
Connector
SAS Drive
Number
Failure
LED
Activity
LED
#0 SAS/SATA/NVMe HDD #0 FAIL #0 ACT #0
#1 SAS/SATA/NVMe HDD #1 FAIL #1 ACT #1
#2 SAS/SATA/NVMe HDD #2 FAIL #2 ACT #2
#3 SAS/SATA/NVMe HDD #3 FAIL #3 ACT #3
#4 SAS/SATA HDD #4 FAIL #4 ACT #4
#5 SAS/SATA HDD #5 FAIL #5 ACT #5
#6 SAS/SATA HDD #6 FAIL #6 ACT #6
#7 SAS/SATA HDD #7 FAIL #7 ACT #7
NVMe#0NVMe#1 NVMe#2 NVMe#3
ACT#0
FAIL#0
ACT#6
ACT#1 ACT#7
ACT#2 ACT#4ACT#3 ACT#5
FAIL#7
FAIL#6
FAIL#5
FAIL#4
FAIL#3FAIL#2
FAIL#1

2-6
BPN-SAS3-743A-N4 Backplane User's Guide
Disclaimer (cont.)
The products sold by Supermicro are not intended for and will not be used in life sup-
port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices, or other critical systems whose failure to
perform would be reasonably expected to result in signicant injury or loss of life or
catastrophic property damage. Accordingly, Supermicro disclaims any and all liability,
and should buyer use or sell such products for use in such ultra-hazardous applications,
it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend,
and hold Supermicro harmless for and against any and all claims, demands, actions,
litigation, and proceedings of any kind arising out of or related to such ultra-hazardous
use or sale.