Supermicro SUPERSERVER 1028R-TDW User manual

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
SUPERSERVER®
1028R-TDW
USER’S MANUAL
1.0a

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 1028R-TDW.
Installation and maintainance should be performed by experienced technicians only.
The SuperServer 1028R-TDW is a 1U rackmount server based on the SC113TQ-
600WB chassis and the X10DDW-i serverboard.
Manual Organization
Chapter 1: Introduction
The rst chapter provides a checklist of the main components included with the
server system and describes the main features of the X10DDW-i serverboard and
the SC113TQ-600WB chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the 1028R-TDW into a rack and
check out the server conguration prior to powering up the system. If your server
was ordered without processor and memory components, this chapter will refer you
to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: Standardized Warning Statements
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 1028R-TDW.
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING
THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING
SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harm-
ful interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-
ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0a
Release Date: April 11, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
SUPERSERVER 1028R-TDW User's Manual
iv
Notes
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X10DDW-i serverboard, including the
locations and functions of connections, headers and jumpers. Refer to this chapter
when adding or removing processors or main memory and when reconguring the
serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC113TQ-600WB server chassis.
You should follow the procedures given in this chapter when installing, removing
or reconguring hard drives and when replacing system power supply units and
cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specications
Preface
v

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Serverboard Features ..................................................................................... 1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
SATA .............................................................................................................. 1-2
Rear I/O Ports................................................................................................. 1-2
1-3 Server Chassis Features ................................................................................ 1-2
System Power................................................................................................. 1-2
Hard Drive Subsystem .................................................................................... 1-3
PCI Expansion Slots ....................................................................................... 1-3
Front Control Panel......................................................................................... 1-3
Cooling System............................................................................................... 1-3
1-4 Contacting Supermicro.................................................................................... 1-5
Chapter 2 Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System .................................................................................... 2-1
2-3 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-2
2-4 Warnings and Precautions.............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations ....................................................................... 2-3
Ambient Operating Temperature ................................................................ 2-3
Reduced Airow ......................................................................................... 2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading..................................................................................... 2-4
Reliable Ground ......................................................................................... 2-4
2-5 Installing the System into a Rack ................................................................... 2-5
Identifying the Sections of the Rack Rails...................................................... 2-5
Inner Rails....................................................................................................... 2-6
Outer Rails ...................................................................................................... 2-7
Chapter 3 System Interface
3-1 Overview ......................................................................................................... 3-1
3-2 Control Panel Buttons ..................................................................................... 3-2
Reset............................................................................................................... 3-2
vii
SUPERSERVER 1028R-TDW User's Manual
Power .............................................................................................................. 3-2
UID .................................................................................................................. 3-3
3-3 Control Panel LEDs ........................................................................................ 3-3
Information LED .............................................................................................. 3-3
NIC2 ................................................................................................................ 3-4
NIC1 ................................................................................................................ 3-4
HDD................................................................................................................. 3-4
Power .............................................................................................................. 3-4
3-4 Hard Drive Carrier LEDs................................................................................. 3-5
Chapter 4 Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements....................................................... 4-1
Warning Denition ........................................................................................... 4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning........................................................................ 4-6
Equipment Installation..................................................................................... 4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................ 4-13
Comply with Local and National Electrical Codes........................................ 4-14
Product Disposal........................................................................................... 4-15
Hot Swap Fan Warning................................................................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard ............................................................................... 5-1
Precautions ..................................................................................................... 5-1
Unpacking ....................................................................................................... 5-1
5-2 Processor and Heatsink Installation................................................................ 5-2
Installing a CPU Heatsink ............................................................................... 5-5
Removing the Heatsink................................................................................... 5-5
5-3 Connecting Cables.......................................................................................... 5-6
Connecting Data Cables ................................................................................. 5-6
Connecting Power Cables .............................................................................. 5-6
Connecting the Control Panel......................................................................... 5-6
5-4 I/O Ports.......................................................................................................... 5-7
5-5 Installing Memory............................................................................................ 5-8
Memory Support.............................................................................................. 5-8
Table of Contents

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
viii
SUPERSERVER 1028R-TDW User's Manual
5-6 Adding PCI Expansion Cards ....................................................................... 5-10
5-7 Mezzanine Card Installation...........................................................................5-11
5-8 Serverboard Details ...................................................................................... 5-12
X10DDW-i Quick Reference ......................................................................... 5-13
5-9 Connector Denitions.................................................................................... 5-15
5-10 Jumper Settings ............................................................................................ 5-21
5-11 Onboard Indicators........................................................................................ 5-24
5-12 SATA Ports .................................................................................................... 5-25
5-13 Installing Software......................................................................................... 5-26
SuperDoctor® 5 ............................................................................................ 5-27
5-14 Onboard Battery............................................................................................ 5-28
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices.................................................................................. 6-1
Precautions ..................................................................................................... 6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 System Fans ................................................................................................... 6-2
System Fan Failure......................................................................................... 6-3
6-4 Drive Bay Installation/Removal ....................................................................... 6-4
Accessing the Drive Bays ............................................................................... 6-4
Hard Drive Installation..................................................................................... 6-4
DVD Drive Installation..................................................................................... 6-7
6-5 Power Supply.................................................................................................. 6-8
Power Supply Failure................................................................................. 6-8
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
Starting BIOS Setup Utility.............................................................................. 7-1
How To Change the Conguration Data ......................................................... 7-1
How to Start the Setup Utility ......................................................................... 7-2
7-2 Main Setup...................................................................................................... 7-2
7-3 Advanced Setup Congurations...................................................................... 7-4
7-4 Event Logs.................................................................................................... 7-31
7-5 IPMI............................................................................................................... 7-33
7-6 Security Settings ........................................................................................... 7-35
7-7 Boot Settings................................................................................................. 7-36
7-8 Save & Exit ................................................................................................... 7-39
Appendix A BIOS Error Beep Codes
Appendix B System Specications

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
Chapter 1
Introduction
1-1 Overview
The SuperServer 1028R-TDW is a 1U server comprised of two main subsystems:
the SC113TQ-600WB chassis and the X10DDW-i serverboard. Please refer to our
website for information on operating systems that have been certied for use with
the system (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the 1028R-TDW, as listed below:
• Five 4-cm server fans (FAN-0086L4)
• Two passive CPU heatsinks (SNK-P0047PS)
• Two riser cards (RSC-R1UW-2E16 and RSC-R1UW-E8R)
• SATA Accessories
One hard drive backplane (BPN-SAS-113TQ)
Eight drive carriers (MCP-220-00047-0B)
Rackmount Rail Kit
• One outer rail set (MCP-290-00101-0N)
• One inner (front) rail set (MCP-290-00107-0N)
• One inner (extension) rail set (MCP-290-00111-0N)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
• Supermicro product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: ftp://ftp.supermicro.com
• Product safety info: http://www.supermicro.com/about/policies/safety_informa-
tion.cfm
Chapter 1: Introduction
1-1

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
1-2 1-3
Chapter 1: Introduction
SUPERSERVER 1028R-TDW User's Manual
1-2 Serverboard Features
At the heart of the SuperServer 1028R-TDW lies the X10DDW-i, a dual processor
serverboard based on the Intel® C612 chipset. Below are the main features of the
X10DDW-i. (See Figure 1-1 for a block diagram of the chipset).
Processors
The X10DDW-i supports two Intel® Xeon E5-2600 (v3/v4) series processors in an
R3-LGA2011 socket. Please refer to our website for a complete listing of supported
processors (www.supermicro.com).
Memory
The X10DDW-i has 16 DIMM sockets that can support up to 2 TB of DDR4-
2400/2133/1866/1600 LRDIMM (Load Reduced DIMMs), or 512 GB of RDIMM
(registered DIMMs) DDR4-2400/2133/1866/1600 memory. Please refer to Chapter
5 for installing memory.
SATA
A SATA controller is integrated into the chipset to provide a ten-port, SATA subsys-
tem, which is RAID 0, 1, and 10 supported. The SATA drives are hot-swappable
units. The serverboard also supports the use of a SATA DOM device.
Rear I/O Ports
The rear I/O ports include one VGA (monitor) port, two USB 2.0 ports, two USB 3.0
ports, two Gb LAN ports and a dedicated IPMI LAN port.
1-3 Server Chassis Features
The SC113TQ-600WB is Supermicro's third-generation 1U chassis and features
eight 2.5" hard drive bays and one high-efciency power supply. The following is a
general outline of the main features of the SC113TQ-600WB chassis.
System Power
When congured as a SuperServer 1028R-TDW, the SC113TQ-600WB chassis
includes a single 600 watt power supply.
Hard Drive Subsystem
The SC113TQ-600WB chassis was designed to support eight hot-swap SATA
hard drives.
PCI Expansion Slots
Two riser cards (RSC-R1UW-2E16-O-P and RSC-R1UW-E8R-O-P) on the left
side of the chassis can support two PCI-E x16 and one PCI-E x8 expansion cards,
respectively. See section 5-6 for further details.)
Front Control Panel
The SC113TQ-600WB control panel provides important system monitoring and
control information. LEDs indicate power on, network activity, hard disk drive activ-
ity and a UID (Universal Information) LED. Also present are a main power button,
a system reset button and a UID button.
Cooling System
The SuperServer 1028R-TDW has an innovative cooling design that features ve
sets of 4-cm counter-rotating fans located in the middle section of the chassis.
There is a "Fan Speed Control Mode" setting in IPMI that allows chassis fan speed
to be determined by system temperature. The power supply module also includes
a cooling fan.

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
1-4 1-5
Chapter 1: Introduction
SUPERSERVER 1028R-TDW User's Manual
Figure 1-1. Intel C612 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.supermicro.com.tw
x16
P1
P1
P0
P0
CPU
FRONT
CPU
DMI
PE1
PE2
PE3
PE3 PE1PE2
DDR4 DIMM
4,5
port 0,1
REAR
DDR4 DIMM
#1
#2
DDR4 DIMM
A
G
x16
RIGHT
SLOT
SXB2
PCIE3.0 x16
x16
RJ45
JLAN1
UL1
RJ45
JLAN2
PHY
RTL8211E
PET
[3,4,6,7]
DMI
PET5
LPC
USB2.0
[6]
QPI
DualLAN
I350BT2
PROCESSOR
PROCESSOR
QPI
DDR4 DIMM
#2#1
DDR4 DIMM
DDR4 DIMM
BMC
SATA
Gen3
[0..5]
2,3
REAR
AST2400
DDR4 DIMM
B
DDR4 DIMM
C
D
SocketID 01
E
H
F
#1
#2
#1
#2
#1 2#
2
##1
#1
#2
#1
#2
x16
Left
SLOT
SXB1B
(lower)
PCIE
3.0
x16
SocketID 00
Left
SLOT
SXB1B
(Upper)
PCIE 3.0 x16
AOM
J35
PCIE
3.0 x16
PCH
SPI
SPI
FLASH
32MB
BMC
DDR3
VGA
IPMI
LAN
RJ45
TPM Header
sSATA
Gen3
[0..3]
HDR
2x5
WIO Slots
SXB1A
SXB1B
SXB1C
SXB2
PCIE x16
Upper Lower
PCIE x16 PCIE x16
Left Slot
Right Slot
HWM COM1
USB2.0
[0..5]
USB3.0
[1..6]
NC _SI(RMII)
x8
S-SATA3
SPI
FLASH
16MB
BIOS
DMI
S-SATA2
S-SATA1
S-SATA0
I-SATA0 I-SATA1
I-SATA2
I-SATA3
I-SATA4
I-SATA5
Rear

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
1-6
SUPERSERVER 1028R-TDW User's Manual
Notes

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 1028R-TDW
up and running. Following these steps in the order given should enable you to have
the system operational within a minimum amount of time. This quick setup assumes
that your system has come to you with the processors and memory preinstalled. If
your system is not already fully integrated with a serverboard, processors, system
memory etc., please turn to the chapter or section noted in each step for details on
installing specic components.
2-2 Unpacking the System
You should inspect the box the SuperServer 1028R-TDW was shipped in and note
if it was damaged in any way. If the server itself shows damage you should le a
damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer
1028R-TDW. It should be situated in a clean, dust-free area that is well ventilated.
Avoid areas where heat, electrical noise and electromagnetic elds are generated.
You will also need it placed near a grounded power outlet. Be sure to read the Rack
and Server Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 1028R-TDW was shipped in should include two sets of
rail assemblies, two rail mounting brackets and the mounting screws you will need
to install the system into the rack. Follow the steps in the order given to complete
the installation process in a minimum amount of time. Please read this section in
its entirety before you begin the installation procedure outlined in the sections that
follow.

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
Chapter 2: Server Installation
2-32-2
SUPERSERVER 1028R-TDW USER'S MANUAL
Choosing a Setup Location
• Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufcient airow and ease in servicing.This product is for
installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).
• This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
2-4 Warnings and Precautions
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains stable.
The following guidelines are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
• When mounting this unit in a partially lled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
Rack Precautions
• Ensure that the leveling jacks on the bottom of the rack are fully extended to
the oor with the full weight of the rack resting on them.
• In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
• Always make sure the rack is stable before extending a component from the
rack.
• You should extend only one component at a time - extending two or more
simultaneously may cause the rack to become unstable.
Server Precautions
• Review the electrical and general safety precautions in Chapter 4.
• Determine the placement of each component in the rack before you install the
rails.
• Install the heaviest server components on the bottom of the rack rst, and then
work up.
• Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
• Allow the hot plug SATA drives and power supply modules to cool before
touching them.
• Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
Rack Mounting Considerations
Warning: Do not pick up the server with the front handles. They are
designed to pull the system from a rack only.
Stability Hazard: The rack stabilizing mechanism must be in place, or the
rack must be bolted to the oor before you slide the unit out for servicing. Failure
to stabilize the rack can cause the rack to tip over.
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient temperature
of the room. Therefore, consideration should be given to installing the equipment
in an environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).
Reduced Airow
Equipment should be mounted into a rack so that the amount of airow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
Chapter 2: Server Installation
2-52-4
SUPERSERVER 1028R-TDW USER'S MANUAL
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power supply
connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).
2-5 Installing the System into a Rack
This section provides information on installing the SuperServer 1028R-TDW into a
rack. If the SuperServer 1028R-TDW has already been mounted into a rack, you
can skip ahead to Sections 2-5 and 2-6.
Note: This rail will t a rack between 26" and 33.5" deep.
There are a variety of rack units on the market, which may mean the assembly
procedure will differ slightly. The following is a guideline for installing the SuperServer
1028R-TDW into a rack with the rack rails provided. You should also refer to the
installation instructions that came with the rack unit you are using.
Identifying the Sections of the Rack Rails
Each assembly consists of two sections: an inner xed chassis rail that secures
directly to the server chassis and an outer xed rack rail that secures directly to
the rack itself.
Figure 2-1. Identifying the Sections of the Rack Rails
Inner Rails
Inner Rail
Extensions
Note: system pictured above includes an optional DVD drive.

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
Chapter 2: Server Installation
2-72-6
SUPERSERVER 1028R-TDW USER'S MANUAL
Figure 2-2. Installing Chassis Rails
Inner Rails
The SC113 chassis includes a set of inner rails in two sections: inner rails and inner
rail extensions. The innerrails are pre-attached and do not interfere with normal use
of the chassis if you decide not to use a server rack. Attach the inner rail extension
to stabilize the chassis within the rack.
Installing the Inner Rails (Figure 2-2)
1. Place the inner rack extensions on the side of the chassis aligning the hooks
of the chassis with the rail extension holes. Make sure the extension faces
"outward" just like the pre-attached inner rail.
2. Slide the extension toward the front of the chassis.
3. Secure the chassis with two screws as illustrated.
4. Repeat steps 1-3 for the other inner rail extension.
1
1
1
2
1
3
Outer Rails
Installing the Outer Rails to the Rack (Figures 2-3 and 2-4)
1. Attach the short bracket to the outside of the long bracket. You must align the
pins with the slides. Also, both bracket ends must face the same direction.
2. Adjust both the short and long brackets to the proper distance so that the rail
ts snugly into the rack.
3. Secure the long bracket to the front side of the outer rail with two M5 screws
and the short bracket to the rear side of the outer rail with three M5 screws.
4. Repeat steps 1-4 for the left outer rail.
Figure 2-3. Assembling the Outer Rails
SCALE 0.500
Secure to the
Front of the Rack
Secure to the
Rear of the Rack
Attach Outer Rails
Together
Warning: Slide rail mounted equipment is not to be used as a shelf or a
work space.
Note: system pictured above includes an optional DVD drive.

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
Chapter 2: Server Installation
2-92-8
SUPERSERVER 1028R-TDW USER'S MANUAL
Figure 2-4. Installing the Outer Rails to the Rack
SCALE 0.380
1
2
1
3
1
3
Figure 2-5. Installing the Server into a Rack
Installing the Chassis into a Rack (Figure 2-5)
1. Conrm that chassis includes the inner rails and rail extensions . Also, conrm
that the outer rails are installed on the rack.
2. Line chassis rails with the front of the rack rails.
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click".
4. (Optional) Insert and tightening the thumbscrews that hold the front of the
server to the rack.
Note: The gure above is for illustrative purposes only. Always install servers to
the bottom of the rack rst.
Note: The gure above is for illustrative purposes only. Always install servers to
the bottom of the rack rst.

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
2-10
SUPERSERVER 1028R-TDW USER'S MANUAL
Notes

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
Chapter 3: System Interface
3-1
Chapter 3
System Interface
3-1 Overview
There are several LEDs on the control panel and on the drive carriers that provide
system and component status for the 1028R-TDW server. This chapter explains the
meanings of all LED indicators and the appropriate responses that need to be taken.
Figure 3-1. System Interface
8
334 12
1
9
6
7
5
10

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
Chapter 3: System Interface
3-2 3-3
SUPERSERVER 1028R-TDW USER'S MANUAL
UID
Depressing the UID (unit identier) button illuminates an LED on both the front and
rear of the chassis for easy system location in large stack congurations. The LED
will remain on until the button is pushed a second time. Another UID button on the
rear of the chassis serves the same function. See the table below for descriptions
of UID LED states.
Universal Information LED States
State Indication
Fast Blinking Red (1x/sec) Fan Fail
Solid Red CPU Overheat
Slow Blinking Red (1x/4 sec) Power Fail
Solid Blue Local UID Button Depressed
Blinking Blue IPMI-Activated UID
Note: deactivating the UID LED must be performed in the same way it was activated.
(If the UID LED was activated via IPMI, you can only turn the LED off via IPMI and
not with the UID button.)
3-2 Control Panel Buttons
There are three buttons located on the front of the chassis: a reset button, a power
on/off button and a UID button.
Reset
Use the reset button to reboot the system.
Power
This is the main power button, which is used to apply or turn off the main system
power. Turning off system power with this button removes the main power but keeps
standby power supplied to the system.
Server Interface Buttons and LEDs
No. Description
1 Power LED
2Device Activity LED
3 LAN1/LAN2 LED
4 Universal Information LED
5 Power Button
6 Reset Button
7 UID Button
8 USB 2.0 Ports
9 Hard Drive Signal
10 Hard Drive Fail
Information LED
See the following table for the status shown by this LED.
Information LED
Status Description
Continously on and red An overheat ocondition has occured. (This may be caused by cable congestion.)
Blinking red (1 Hz) Fan failure: check for an inoperative fan.
Blinking red (0.25 Hz) Power failure: check for an inoperative power supply.
Solid blue Local UID has been activated. Use this function to locate the server in a rack
environment.
Blinking blue (300 msec) Remote UID has been activated. Use this function to locate the server from a
remote location.
3-3 Control Panel LEDs
The control panel located on the front of the SC113TQ-600WB chassis has ve
LEDs. These LEDs provide you with critical information related to different parts of
the system. This section explains what each LED indicates when illuminated and
any corrective action you may need to take.

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
Chapter 3: System Interface
3-4 3-5
SUPERSERVER 1028R-TDW USER'S MANUAL
NIC2
Indicates network activity on LAN2 when ashing.
NIC1
Indicates network activity on LAN1 when ashing.
HDD
Indicates IDE channel activity when ashing.
2
1
3-4 Hard Drive Carrier LEDs
Each hard drive carrier has two LEDs.
• Green: When illuminated, the green LED on the front of the drive carrier
indicates drive activity. A connection to the drive backplane enables this LED to
blink on and off when that particular drive is being accessed.
• Red: The red LED indicates two states. When blinking, it indicates the drive is
rebuilding. When solid, it indicates a drive failure. If a hard drive fails, you should
be notied by your system management software. Please refer to Chapter 6 for
instructions on replacing failed hard drives.
Power
Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
3-6
SUPERSERVER 1028R-TDW USER'S MANUAL
Notes

WIT.RU
WIT Company – поставка серверов, СХД,
сетевого оборудования, лицензионного ПО
4-1
Chapter 4: Warning Statements for AC Systems
Chapter 4
Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certied technicians should attempt to install or congure
components.
Read this appendix in its entirety before installing or conguring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
Warning Denition
警告の定義
この警告サインは危 険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸
電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。