Supermicro Supero C7Z370-CG-IW User manual

C7Z370-CG-IW

C7Z370-CG-IW QUICK REFERENCE GUIDE Product Safety Information
Standardized Warning Statements
Motherboards
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of situations which can potentially
cause a bodily injury. Should you have questions or experience difculty, contact Supermicro's Technical Support De-
partment for assistance. Only certied technicians should attempt to install or congure components.
Read this section in its entirety before installing or conguring components in the Supermicro chassis.
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-
lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメーカーが推奨する型、または同等のもの
を使用下さい。 使用済電池は製造元の指示に従って処分して下さい。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理
廢棄舊電池。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理
废旧电池。
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한
종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Note: For complete product safety information, refer to http://www.supermicro.com/about/policies/safety_information.cfm.





C7Z370-CG-IW QUICK REFERENCE GUIDE 限用物質含有情況標示聲明書
限用物質含有情況標示聲明書
設備名稱：主機板 /
Motherboard
單元Ｕnit
限用物質及其化學符號
鉛Lead
(Pb) 汞Mercury (Hg) 鎘Cadmium (Cd)
六價鉻
Hexavalent
chromium
(Cr+6)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
主機板
(Motherboard)
－○ ○ ○ ○ ○
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準
值。
備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考3.〝－〞係指該項限用物質為排除項目。
Equipment name
型號（型式）：C7Z370-CG-IW
Type designation (Type)
Restricted substances and its chemical symbols
Declaration of the Presence Condition of the Restricted Substances Marking
Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the
reference percentage value of presence condition.
Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3：The “−” indicates that the restricted substance corresponds to the exemption.

C7Z370-CG-IW QUICK REFERENCE GUIDE BIOS POST Code
AMI BIOS POST Codes
About AMI BIOS POST Codes
The table below lists some of AMI BIOS POST codes. For more information, refer to https://www.supermicro.com.tw/
manuals/other/AMI_BIOS_POST_Codes_for_Grantley_Motherboards.pdf.
Code Description
0x32 CPU post-memory initialization is started
0x55 No Memory detected or memory failed
0x63 CPU DXE initialization is started
0x69 North Bridge DXE initialization is started
0x70 South Bridge DXE initialization is started
0x92 PCI Bus initialization is started
0x99 Super IO Initialization
0x9A USB initialization is started
0xA0 IDE initialization is started
0xA9 Boot into BIOS setup menu
0xAE Legacy Boot event
0xB2 Legacy Option ROM Initialization
0xB4 USB hot plug
0xD6 No VGA device
0xD7 No Keyboard plug in
0xF2 Recovery process started
0xF9 Recovery capsule is not found

C7Z370-CG-IW QUICK REFERENCE GUIDE
Notes
Notes

C7Z370-CG-IW
Quick RefeRence Guide Rev. 1.0
SUPERMICR R
A
C
A
C
DESIGNED IN USA
C7Z370-CG-IW
REV:1.01
MAC CODE
BAR CODE
JWD1 J9701 J9702
JPME2
JBR1
I-SATA3 I-SATA2
I-SATA1 I-SATA0
LED2
LED5
JD1
JF1
JSD1 JPW1
LED1
JPW2
JCMOS OC1
JSPDIF_OUT
JL1
CPU LED
BOOT LED DIMM LED VGA LED
CPU
MH12
B1
JRLED1
PCI-E M.2-E1
PCI-E M.2-M1
SYS_FAN1 CPU_FAN1
USB 6/7(3.0)
DIMMB1
DIMMA1
CPU SLOT7 PCI-E 3.0 X16
JUSBLAN1
JUSBC
LED HDD
LED PWR
ON
PWR RST
X
OH/FF 1
NIC
X
USB 8/9(3.1)
USB 4/5(3.0) HDMI/DP
USB 0/1
HD AUDIO
AUDIO FP
JPUSB1
PS/2 KB/MOUSE
USB 2/3 (3.0)
Motherboard Layout and Features
8th Gen
Intel® CoreTM i7/i5/i3
Series CPU
=mounting hole
LGA 1151
I/O BACK PANEL

Package contents
• One (1) Supermicro Motherboard
• Four (2) SATA Cables, One (1) I/O Shield
• One (1) Quick Reference, One (1) Driver CD
Jumpers and Connectors
Jumpers
Connectors
Jumper Description Default
JCMOS Clear CMOS Open: Normal
Short: Clear CMOS
J9701/J9702 Manufacturing Mode 1-2: Normal
JBR1 BIOS Recovery 1-2: Normal
JPME2 Intel®Manufacturing Mode 1-2: Normal
JPUSB1 USB Wake Up Enable (Back Panel USB 2/3) 1-2: Enable
JWD1 Watch Dog Function Enable 1-2: Reset
Connector Description
AUDIO FP Front Panel Audio Header
B1 RTC Battery
CPU_FAN1 CPU Fan Header
CPU SLOT7 PCI-E 3.0 x16 PCI Express x16 Slot (PCI-E 3.0 x16 link)
HD AUDIO High Denition Audio
HDMI/DP High Denition Multimedia Interface/DisplayPort
I-SATA0~3 (Intel®Z370) Serial ATA (SATA) 3.0 (6Gb/sec)
JD1 External Speaker Header
JF1 Front Control Panel Header
JL1 Chassis Intrusion Header
JPW1 24-pin ATX Main Power Connector (Required)
JPW2 8-pin CPU Power Connector (Required)
JRLED1 RGB Header
JSD1 SATA DOM (Disk-On-Module) Power Connector
JSPDIF_OUT Sony/Philips Digital Interface (S/PDIF) Out Header
KB/MOUSE PS/2 Keyboard/Mouse Port
LAN RJ45 GbE LAN Port
OC1 2-pin Header for Overclocking Setting
PCI-E M.2 CONNECTOR M1,
M2
PCI-E M.2 Connectors (Small form factor devices and other portable devices
for high speed NVMe SSDs)
*PCI-E M.2 CONNECTOR M2 is on the bottom side of the board
PCI-E M.2 -E1 Wi+BT
SYS_FAN1 System Fan Header
USB 0/1 Front Panel Universal Serial Bus (USB) 2.0 Ports (Black)
USB 2/3, USB 4/5(3.0) Back Panel USB 3.0 Ports (Blue)
USB 6/7(3.0) Front Panel Accessible USB 3.0 Headers (Blue)
USB 8/9 (3.1) Back Panel USB 3.1 Type A (Red) , Type C Ports (Red)

ContaCt InformatIon
• www.supermicro.com (Email: [email protected])
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
Note: 1) For memory optimization, use only DIMM modules that have been validated by Supermicro. For the latest memory updates, please
refer to our website at http://www.supermicro.com/products/motherboard.
2) Always connect the power cord last, and always remove it before adding, removing or changing any hardware components.
3) Only use 8th Generation Intel® CoreTM i7/i5/i3/Pentium®/Celeron® to boot up, otherwise system will not be powered on.
LED Indicators
LED indicators
CPU & Memory Support
Towards the CPU
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the following order:
DIMMA1, then DIMMB1.
• Always use DDR4 DIMM modules of the same size, type and speed.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed of the slowest DIMM.
Recommended Population (Balanced)
DIMMA1 DIMMB1 Total System Memory
4GB 4GB 8GB
8GB 8GB 16GB
16GB 16GB 32GB
DIMMB1 (Grey Slot)
DIMMA1 (Grey Slot)
DIMM Memory Installation
The C7Z370-CG-IW supports an 8th Gen Intel® CoreTM i7/i5/i3/Pentium®/Celeron® processor, up to 32GB of Unbuf-
fered (UDIMM) non-ECC DDR4 memory, 2666MHz to 3733+MHz (OC) in two 288-pin memory slots. Populating these
DIMM slots with a pair of memory modules of the same type and same size will result in interleaved memory, which
will improve memory performance.
LED Description Color/State
BOOT LED Bootable Device POST (Power-On Self-
Test) Status
Bootable Device POST: Red ON
Bootable Device POST Completion: OFF
CPU LED CPU POST(Power-On Self-Test) Status CPU POST: Yellow ON
CPU POST Completion: OFF
DIMM LED DIMM POST(Power-On Self-Test) Status DIMM POST: Blue ON
DIMM POST Completion: OFF
VGA LED Onboard VGA POST (Power-On Self-Test)
Status
Onboard VGA POST: Green ON
Onboard VGA POST Completion: OFF
LED1 Power On: Green On
S3 (Suspend to RAM) LED
Power On: Green ON
S3: Green Blinking
LED2 PCI-E M.2 Connector #2 LED PCI-E/SATA Device Detected: Green ON
Activlity: Green Blinking
LED5 PCI-E M.2 Connector #1 LED PCI-E Device Detected: Green ON
Activlity: Green Blinking

MNL-2028-QRG-100
© 2017 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
Notes
• Graphics shown in this quick reference guide are for illustration only. Your components may or
may not look exactly the same as drawings shown in this guide.
• Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, LED
indicators, memory support and CPU/motherboard installation instructions.
Front Control Panel (JF1)
CPU Installation Heatsink Installation
Heatsink
with Fan
Motherboard
Mounting Hole
Back Panel I/O Connectors
C7Z370-CG-IW
Add
thermal paste
Power Button
Overheat/
Fan Fail LED (-)
1
NIC1 LED (-)
Reset Button
2
HDD LED (-)
POWER LED (-)
Reset
PWR
POWER LED (+)
Ground
Ground
XX
HDD LED (+)
NIC1 LED (+)
Overheat/
Fan Fail LED (+)
1516
XX
A. PS/2 Keyboard/Mouse Port F. Wi+BT K. USB 3.1 Port 9 (Type C) P. Line Out
B. USB 3.0 Port 2 G. USB 3.0 Port 4 L. Center/LFE Out Q. Mic In
C. USB 3.0 Port 3 H. USB 3.0 Port 5 M. Surround Out
D. Display Port I. Gigabit Ethernet RJ45 LAN
Port
N. S/PDIF Out
E. HDMI Port J. USB 3.1 Port 8 (Type A) O. Line In
A
B
C
D
EF
G
H
I
J
K
L
M
N
O
P
Q

美超微電腦股份有限公司
C7Z370-CG-IW 快速參考指南 版本 1.00
SUPERMICR R
主機板元件配置圖
A
C
A
C
DESIGNED IN USA
C7Z370-CG-IW
REV:1.01
MAC CODE
BAR CODE
JWD1 J9701 J9702
JPME2
JBR1
I-SATA3 I-SATA2
I-SATA1 I-SATA0
LED2
LED5
JD1
JF1
JSD1 JPW1
LED1
JPW2
JCMOS OC1
JSPDIF_OUT
JL1
CPU LED
BOOT LED DIMM LED VGA LED
CPU
MH12
B1
JRLED1
PCI-E M.2-E1
PCI-E M.2-M1
SYS_FAN1 CPU_FAN1
USB 6/7(3.0)
DIMMB1
DIMMA1
CPU SLOT7 PCI-E 3.0 X16
JUSBLAN1
JUSBC
LED HDD
LED PWR
ON
PWR RST
X
OH/FF 1
NIC
X
USB 8/9(3.1)
USB 4/5(3.0) HDMI/DP
USB 0/1
HD AUDIO
AUDIO FP
JPUSB1
PS/2 KB/MOUSE
USB 2/3 (3.0)
8th Gen
Intel® CoreTM i7/i5/i3
Series CPU
= 裝機孔
LGA 1151
I/O BACK PANEL