Supermicro SUPERSERVER 6018R-TD User manual

SUPERSERVER®
6018R-TD
USER’S MANUAL
1.0a

iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 6018R-TD.
Installation and maintenance should be performed by experienced technicians only.
The SuperServer 6018R-TD is a server based on the SC813TS-441CBP 1U rack-
mount chassis and the Super X10DRD-L serverboard.
Manual Organization
Chapter 1: Introduction
The rst chapter provides a checklist of the main components included with the
server system and describes the main features of the X10DRD-L serverboard and
the SC813TS-441CBP chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 6018R-TD
into a rack and check out the server conguration prior to powering up the system.
If your server was ordered without processor and memory components, this chapter
will refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: Standardized Warning Statements
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6018R-TD.
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu-
mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-
ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro-
ductive harm.
Manual Revision 1.0a
Release Date: April 14, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

v
SUPERSERVER 6018R-TD User's Manual Preface
iv
Notes
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X10DRD-L serverboard, including the
locations and functions of connections, headers and jumpers. Refer to this chapter
when adding or removing processors or main memory and when reconguring the
serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC813TS-441CBP server chassis.
You should follow the procedures given in this chapter when installing, removing or
reconguring hard drives and when replacing system power supply modules and
cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specications

vii
Table of Contents
vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Serverboard Features ..................................................................................... 1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
SATA................................................................................................................ 1-2
PCI-Expansion ................................................................................................ 1-2
Rear I/O Ports................................................................................................. 1-2
Onboard Graphics........................................................................................... 1-2
1-3 Server Chassis Features ................................................................................ 1-3
System Power................................................................................................. 1-3
SATA Subsystem............................................................................................. 1-3
Control Panel .................................................................................................. 1-3
Cooling System............................................................................................... 1-3
1-4 Contacting Supermicro.................................................................................... 1-5
Chapter 2 Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System .................................................................................... 2-1
2-3 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-1
2-4 Warnings and Precautions.............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations ....................................................................... 2-3
Ambient Operating Temperature ................................................................ 2-3
Reduced Airow ......................................................................................... 2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-3
2-4 Rack Mounting Instructions............................................................................. 2-4
Identifying the Sections of the Rack Rails...................................................... 2-4
Inner Rail Extension........................................................................................ 2-5
Installing the Chassis into a Telco rack .......................................................... 2-9
Chapter 3 System Interface
3-1 Overview ......................................................................................................... 3-1
3-2 Control Panel Buttons ..................................................................................... 3-1
Reset............................................................................................................... 3-1
Power .............................................................................................................. 3-1
3-3 Control Panel LEDs ........................................................................................ 3-2
Information LED .............................................................................................. 3-2
NIC1 ................................................................................................................ 3-2
NIC2 ................................................................................................................ 3-3
HDD................................................................................................................. 3-3
Power .............................................................................................................. 3-3
3-4 Hard Drive Carrier LEDs................................................................................. 3-3
Chapter 4 Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements....................................................... 4-1
Warning Denition ........................................................................................... 4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning........................................................................ 4-6
Equipment Installation..................................................................................... 4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................ 4-13
Comply with Local and National Electrical Codes........................................ 4-14
Product Disposal........................................................................................... 4-15
Hot Swap Fan Warning................................................................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard ............................................................................... 5-1
Precautions ..................................................................................................... 5-1
5-2 Processor and Heatsink Installation................................................................ 5-2
Installing a Passive CPU Heatsink ................................................................. 5-5
Removing the Heatsink................................................................................... 5-5
5-3 Connecting Cables.......................................................................................... 5-6
Connecting Data Cables ................................................................................. 5-6
Connecting Power Cables .............................................................................. 5-6
Connecting the Control Panel......................................................................... 5-6
5-4 I/O Ports.......................................................................................................... 5-7
5-5 Installing Memory............................................................................................ 5-8
5-6 Adding PCI Expansion Cards ....................................................................... 5-10
5-7 Serverboard Details .......................................................................................5-11
X10DRD-L Quick Reference ......................................................................... 5-12
5-8 Connector Denitions ................................................................................... 5-13
SUPERSERVER 6018R-TD User's Manual

viii
5-9 Jumper Settings ............................................................................................ 5-19
5-10 Onboard Indicators........................................................................................ 5-21
5-11 SATA Ports .................................................................................................... 5-22
5-12 Installing Drivers............................................................................................ 5-23
SuperDoctor® 5 ............................................................................................ 5-24
5-13 Onboard Battery............................................................................................ 5-25
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices.................................................................................. 6-1
Precautions ..................................................................................................... 6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 System Fans ................................................................................................... 6-3
System Fan Failure......................................................................................... 6-3
6-4 Drive Bay Installation/Removal ....................................................................... 6-5
Removing the Front Bezel .............................................................................. 6-5
Accessing the Drive Bays ............................................................................... 6-5
SATA Drive Installation.................................................................................... 6-6
SATA Power Cables ................................................................................... 6-7
SATA Backplane......................................................................................... 6-7
DVD Drive Installation..................................................................................... 6-8
6-5 Power Supply.................................................................................................. 6-9
Power Supply Failure...................................................................................... 6-9
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
Starting BIOS Setup Utility.............................................................................. 7-1
How To Change the Conguration Data ......................................................... 7-1
How to Start the Setup Utility ......................................................................... 7-2
7-2 Main Setup...................................................................................................... 7-2
7-3 Advanced Setup Congurations...................................................................... 7-4
7-4 Event Logs .................................................................................................... 7-31
7-5 IPMI............................................................................................................... 7-33
7-6 Security Settings ........................................................................................... 7-35
7-7 Boot Settings................................................................................................. 7-39
7-8 Save & Exit ................................................................................................... 7-42
Appendix A BIOS Error Beep Codes
Appendix B System Specications
SUPERSERVER 6018R-TD User's Manual

Chapter 1
Introduction
1-1 Overview
The SuperServer 6018R-TD is a 1U server comprised of two main subsystems:
the SC813TS-441CBP chassis and the X10DRD-L serverboard. Please refer to our
website for information on operating systems that have been certied for use with
the system (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the 6018R-TD, as listed below:
• Two 10-cm blower fans (FAN-0135L4)
• One 4-cm fan (FAN-0065L4)
• Two passive CPU heatsinks (SNK-P0047PS)
• One RSC-RR1U-E8 riser card
• SATA Accessories
One SATA backplane (BPN-SAS-815T)
Four 3.5" hard drive carriers (MCP-220-00075-0B)
One SATA cable (CBL-01801-01)
• One rail kit consisting of one set each of outer rails (MCP-290-00102-0N) and
inner rails (MCP-290-00106-0N)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
• Supermicro product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: ftp://ftp.supermicro.com
• Product safety info: http://www.supermicro.com/about/policies/safety_informa-
tion.cfm
• If you have any questions, please contact our support team at:
[email protected]m
Chapter 1: Introduction
1-1

1-2 1-3
Chapter 1: Introduction
SUPERSERVER 6018R-TD User's Manual
1-2 Serverboard Features
At the heart of the SuperServer 6018R-TD lies the X10DRD-L, a dual processor
serverboard based on Intel's C612 chipset. Below are the main features of the
X10DRD-L (see Figure 1-1 for a block diagram of the chipset).
Processors
The X10DRD-L supports single or dual Intel®Xeon®E5-2600 v3/v4 Series proces-
sors in LGA2011-3 (Socket R3) sockets. Please refer to the serverboard description
pages on our website for a complete listing of supported processors.
Memory
The X10DRD-L has eight DIMM sockets that can support up to 1 TB of ECC
LRDIMM (Load Reduced DIMMs) or 512 GB of ECC RDIMM (Registered DIMMs)
DDR4-2400/2133/1866/1600 memory. Please refer to Chapter 5 for installing
memory.
SATA
An on-chip SATA controller is integrated into the X10DRD-L to provide a six-port,
SATA 3.0 subsystem, which is RAID 0, 1, 5 and 10 supported. The SATA drives
are hot-swappable units.
Note: Documentation on RAID setup guidelines can be found on our website.
PCI-Expansion
One PCI-E 3.0 x8 slot is included on the X10DRD-L. One expansion card may
be added to the system with the included riser card. (See Section 5-6 for details.)
Rear I/O Ports
The rear I/O panel include one COM port, a VGA (monitor) port, four USB 2.0 ports
and two gigabit Ethernet ports. A dedicated IPMI LAN port is also included.
Onboard Graphics
The X10DRD-L provides onboard graphics with an Aspeed 2400 BMC (baseboard
management controller).
1-3 Server Chassis Features
The following is a general outline of the main features of the SC813TS-441CBP
chassis.
System Power
The SC813TS-441CBP chassis includes a single 440-480W power supply. Power
must be removed from the system when removing the power supply. See Chapter
6 for details.
SATA Subsystem
For the 6018R-TD, the SC813TS-441CBP chassis was designed to support four
SATA hard drives, which are hot-swappable units.
Control Panel
The SC813TS-441CBP's control panel provides important system monitoring and
control information. LEDs indicate power on, network activity, hard disk drive activity
and an information LED. The control panel also includes a main power button and
a system reset button.
Cooling System
The SC813TS-441CBP chassis has an innovative cooling design that features two
10-cm blower fans and one 4-cm fan. Each of these fans plug into a fan header
on the serverboard.

1-4 1-5
Chapter 1: Introduction
SUPERSERVER 6018R-TD User's Manual
Figure 1-1. Intel C612 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.supermicro.com.tw
JLAN2
X10DRD-L/LT
4 PHASE
145W
VR12.5
VCCP1 12v
x8
P2P2
P1P1
DMIPE1PE2PE3
PE3
PE1
PE2
DDR4 DIMM
4,5
port 0,1
REAR 2.0
DDR4 DIMM
#1
DDR4 DIMM
E
A
PROCESSOR
PROCESSOR
DDR4 DIMM
#1
DDR4 DIMM
DDR4 DIMM
2,3
REAR 2.0
DDR4 DIMM
F
DDR4 DIMM
G
H
CPU1 (Left)
C
D B
#1 #1
4 PHASE
145W
VR12.5
VCCP0 12v
8
x8
9.6 GT/s
QPI
CPU2 (Right)
QPI
4GB/s
DMI
sSATA Gen3 [0..3]
I-SATA0
I-SATA1
I-SATA2
I-SATA3
I-SATA4
I-SATA5
Type A 2.0
HDR 2x5 2.0
PET [3,4,6,7]
SATA Gen3 [0..5]
PCH
USB2.0 [0..11]
USB3.0 [1..5]
LPCUSB2.0 [6,7]
SPI
PET5
TPM Header
IPMI LAN
RJ45
PHY
RTL8211E
COM1
COM2
HWM
BMC
AST2400
VGA
DDR3
16MB BMC
SPI FLASH
16MB BIOS
SPI FLASH
NC-SI(RMII)
JPCIE4
PCIE SLOT 3.0 X8
LANE8~15
DMI
#1 #1 #1 #1
JLAN1 Dual LAN
Intel i350 or Intel X540
LANE8~15
SLOT #6
Note: the Intel X540 controller is not included on the X10DRD-L serverboard model.

1-6
SUPERSERVER 6018R-TD User's Manual
Notes

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your system installed into a
rack. Be aware of the warnings and precautions mentioned in this chapter when
installing the server into a rack.
2-2 Unpacking the System
You should inspect the box the server was shipped in and note if it was damaged
in any way. If the chassis itself shows damage, le a damage claim with the carrier
who delivered it.
2-3 Preparing for Setup
Decide on a suitable location for the rack unit that will hold your chassis. It should
be a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical
noise and electromagnetic elds are generated. A nearby grounded power outlet.
is required
The box your chassis was shipped in should include two sets of rail assemblies, two
rail mounting brackets and the mounting screws to mount the system into the rack.
Please read this chapter in its entirety before beginning the installation procedure.
Choosing a Setup Location
• Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufcient airow and ease in servicing.This product is for
installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).
• This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.

Chapter 2: Server Installation
2-32-2
SUPERSERVER 6018R-TD User's Manual
2-4 Warnings and Precautions
Rack Precautions
• Ensure that the leveling jacks on the bottom of the rack are fully extended to
the oor with the full weight of the rack resting on them.
• In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
• Always make sure the rack is stable before extending a component from the
rack.
• You should extend only one component at a time - extending two or more si-
multaneously may cause the rack to become unstable.
• Rack-mounted equipment should not be used as a shelf or work space.
Server Precautions
• Review the electrical and general safety precautions in Chapter 4.
• Determine the placement of each component in the rack before you install the
rails.
• Install the heaviest server components on the bottom of the rack rst, and then
work up.
• Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
• Allow the hot plug SATA drives and power supply modules to cool before touch-
ing them.
• Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient temperature
of the room. Therefore, consideration should be given to installing the equipment
in an environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).
Reduced Airow
Equipment should be mounted into a rack so that the amount of airow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power supply
connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
• When mounting this unit in a partially lled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.

Chapter 2: Server Installation
2-52-4
SUPERSERVER 6018R-TD User's Manual
SCALE 0.500
Figure 2-1. Identifying the Sections of the Rack Rails
(right side rail shown)
SCALE 0.500
Rail Extension
(Inner Rail is pre-installed
on the chassis)
Outer Rails
2-4 Rack Mounting Instructions
This section provides information on installing the SC813TS-441CBP chassis into
a rack unit. There are a variety of rack units on the market, which may mean the
assembly procedure will differ slightly. You should also refer to the installation
instructions that came with the rack unit you are using.
Note: This rail will t a rack between 26" and 33.5" deep.
Identifying the Sections of the Rack Rails
The chassis package includes two rack rail assemblies in the rack mounting kit.
Each assembly consists of two sections: an inner rail that secures directly to the
chassis, and an outer rail that secures directly to the rack itself.
Figure 2-2. Identifying the Sections of the Rack Rails
(right side rail shown)
Inner Rail Extension
The SC813TS-441CBP chassis includes a set of inner rails which are in two
sections: inner rails and inner rail extensions. The inner rails are pre-attached and
do not interfere with normal use of the chassis if you decide not to use a server
rack. Attach the inner rail extension to stabilize the chassis within the rack.
Installing the Inner Rails
1. Place the inner rail extensions on the side of the chassis aligning the hooks
of the chassis with the inner rail extension holes. Make sure the inner rail
extension faces "outward" just like the pre-attached inner rail.
2. Slide the extension toward the front of the chassis.
3. Secure the chassis with 2 screws as illustrated.
4. Repeat steps 1-3 for the other inner rail extension.
1
1
1
2
1
3

Chapter 2: Server Installation
2-72-6
SUPERSERVER 6018R-TD User's Manual
Installing the Outer Rails to the Rack
1. Attach the longer section of the outer rail to the outside of the shorter section
of the outer rail. You must align the pins with the slides. Both ends of the
outer rail must face the same direction in order to be secured to the rack.
2. Adjust both sections of the outer rail to the proper length so that the rail ts
snugly within the rack.
3. Secure the longer section of the outer rail to the of the rack with two M5
screws and the shorter section to the rear side of the rack with two M5
screws.
4. Repeat steps 1-4 for the remaining outer rail.
SCALE 0.500
Secure to the
Front of the Rack
Secure to the
Rear of the Rack
Figure 2-3. Assembling the Outer Rails
Attach the Two Sections of the
Outer Rail Together
Figure 2-4. Installing the Outer Rails to the Server Rack
SCALE 0.380
1
2
1
3
1
3
Slide rail mounted equipment is not to be used as a shelf or a work space.
Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the oor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.
Warning: When initially installing the server to a rack, test that the rail
locking tabs engage to prevent the server from being overextended. Have
a rack lift in place as a precaution in case the test fails.
Note: Figures are for illustrative purposes only. Servers should always be installed
into racks starting at the bottom.

Chapter 2: Server Installation
2-92-8
SUPERSERVER 6018R-TD User's Manual
Figure 2-5. Installing the Rack Rails
Installing the Chassis into a Rack
1. Conrm that chassis includes the inner rails (A) and rail extensions (B). Also,
conrm that the outer rails (C) are installed on the rack.
2. Line chassis rails (A and B) with the front of the rack rails (C).
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When
pushed completely into the rack, you should hear the locking tabs "click" into
the locked position.
4. (Optional) Insert and tighten the thumbscrews on the front of the server
1
A
1
B
1
C
Figure 2-6. Installing the Server into a Telco Rack
Installing the Chassis into a Telco rack
To install the chassis into a Telco type rack, use two L-shaped brackets on either
side of the chassis (four total). First, determine how far follow the server will extend
out the front of the rack. Larger chassis should be positioned to balance the weight
between front and back. If a bezel is included on your server, remove it. Then at-
tach the two front brackets to each side of the chassis, then the two rear brackets
positioned with just enough space to accommodate the width of the telco rack.
Finish by sliding the chassis into the rack and tightening the brackets to the rack.
Note: Figures are for illustrative purposes only. Servers should always be installed
into racks starting at the bottom.
Note: Figures are for illustrative purposes only. Servers should always be installed
into racks starting at the bottom.

2-10
SUPERSERVER 6018R-TD User's Manual
Notes

Chapter 3: System Interface
3-1
Chapter 3
System Interface
3-1 Overview
There are several LEDs on the control panel as well as others on the hard drive
carriers to keep you constantly informed of the overall status of the system as well
as the activity and health of specic components. There are also two buttons on
the chassis control panel.
This chapter explains the meanings of all LED indicators and the appropriate re-
sponse you may need to take.
3-2 Control Panel Buttons
There are two push-buttons located on the front of the chassis: a reset button and
a power on/off button.
Reset
The reset button reboots the system.
Power
This is the main power button, which is used to apply or turn off the main system
power. Turning off system power with this button removes the main power but keeps
standby power supplied to the system.

Chapter 3: System Interface
3-2 3-3
SUPERSERVER 6018R-TD User's Manual
Information LED States
State Indication
Fast Blinking Red (1x/sec) Fan Fail
Solid Red CPU Overheat
Slow Blinking Red (1x/4
sec) Power Fail
Solid Blue Local UID Button Depressed
Blinking Blue IPMI-Activated UID
3-3 Control Panel LEDs
The control panel located on the front of the SC813TS-441CBP chassis has ve
LEDs. These LEDs provide you with critical information related to different parts of
the system. This section explains what each LED indicates when illuminated and
any corrective action you may need to take.
Power
Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.
3-4 Hard Drive Carrier LEDs
Each drive carrier has two LEDs.
• Green: When illuminated, the green LED on the drive carrier indicates drive
activity. A connection to the backplane enables this LED to blink on and off
when that particular drive is being accessed.
• Red: The red LED to indicate a drive failure. If one of the drives fails, you should
be notied by your system management software. Please refer to Chapter 6 for
instructions on replacing failed drives.
1
2
Information LED
This LED will be blue when the UID function has been activated. When this LED
ashes red, it indicates a fan failure. When red continuously it indicates an overheat
condition, which may be caused by cables obstructing the airow in the system or
the ambient room temperature being too warm. Check the routing of the cables
and make sure all fans are present and operating normally. You should also check
to make sure that the chassis covers are installed. Finally, verify that the heatsinks
are installed properly (see Chapter 5). This LED will remain ashing or on as long
as the indicated condition exists.
NIC1
Indicates network activity on LAN1 when ashing.
NIC2
Indicates network activity on LAN2 when ashing.
HDD
Channel activity for all HDDs. This light indicates hard drive activity on the 6018R-
TD when ashing.

3-4
SUPERSERVER 6018R-TD User's Manual
Notes

4-1
Chapter 4: Warning Statements for AC Systems
Chapter 4
Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certied technicians should attempt to install or congure
components.
Read this appendix in its entirety before installing or conguring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning Denition
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
警告の定義
この警告サインは危 険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸
電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。

4-2
SUPERSERVER 6018R-TD User's Manual
4-3
Warning Statements for AC Systems
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie benden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
nal de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES.
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la n de chaque avertissement.
CONSERVEZ CES INFORMATIONS.
안전을 위한 주의사항
경고!
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준 작업절차를
준수해 주시기 바랍니다.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
.   !




ןונקת תורהצהאהרהז
ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח
ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק
רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר
אורקל שי .ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא