Supermicro SUPERSERVER 5018D-FN8T User manual

USER’S MANUAL
Revision 1.0
SUPERSERVER®
5018D-FN8T
Проконсультироваться икупить данное оборудование вы можете вкомпании «АНД-Системс»
адрес: 125480, г.Москва, ул.Туристская, д.33/1; site: https://andpro.ru тел: [phone] email: [email protected]
При обращении используйте промокод AND-PDF иполучите скидку.

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0
Release Date: June 22, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

iii
Preface
Preface
About this Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer. Installation and
maintenance should be performed by experienced technicians only.
Please refer to the server specications page on our Web site for updates on
supported memory, processors and operating systems (http://www.supermicro.
com).
Warnings
Special attention should be given to the following symbols used in this manual.
Warning! Indicates high voltage may be encountered when performing
a procedure.
Warning! Indicates important information given to prevent equipment/
property damage or personal injury.

iv
SUPERSERVER 5018D-FN8T Manual
Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Motherboard Features..................................................................................... 1-2
Processors ..................................................................................................... 1-2
Memory ........................................................................................................... 1-2
Serial ATA ....................................................................................................... 1-2
Input/Output Ports........................................................................................... 1-2
PCI Expansion Slots ....................................................................................... 1-2
1-3 Server Chassis Features ............................................................................... 1-4
System Power................................................................................................. 1-4
Drives .............................................................................................................. 1-4
Control Panel ................................................................................................. 1-4
PCI Expansion ................................................................................................ 1-4
Cooling System .............................................................................................. 1-4
1-4 Contacting Supermicro.................................................................................... 1-5
Chapter 2 Installation in a Rack
2-1 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-1
2-2 Warnings and Precautions.............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations ....................................................................... 2-3
Ambient Operating Temperature ................................................................ 2-3
Reduced Airow ......................................................................................... 2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-3
2-3 Installing the System into a Rack .................................................................. 2-4
Installing the Chassis into a Rack:.................................................................. 2-4
Chapter 3 System Interface
3-1 Overview ........................................................................................................ 3-1
3-2 Control Panel Buttons ..................................................................................... 3-2
3-3 Control Panel LEDs ........................................................................................ 3-2
Overheating..................................................................................................... 3-3
Overheat Temperature Setting ................................................................... 3-3
Responses.................................................................................................. 3-3
3-4 Power Supply LEDs ........................................................................................ 3-4

v
Contents
Chapter 4 Standardized Warning Statements for AC Systems
About Standardized Warning Statements....................................................... 4-1
Warning Denition........................................................................................... 4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning ........................................................................ 4-6
Equipment Installation..................................................................................... 4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies (if applicable to your system)........................... 4-12
Backplane Voltage (if applicable to your system)......................................... 4-13
Comply with Local and National Electrical Codes........................................ 4-14
Product Disposal........................................................................................... 4-15
Hot Swap Fan Warning (if applicable to your system) ................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Motherboard Setup
5-1 Handling the Motherboard .............................................................................. 5-1
Precautions ..................................................................................................... 5-1
Unpacking ....................................................................................................... 5-1
5-2 Connecting Cables.......................................................................................... 5-2
Connecting Data Cables ................................................................................. 5-2
Connecting Power Cables .............................................................................. 5-2
Connecting the Control Panel......................................................................... 5-2
5-3 Input/Output Ports........................................................................................... 5-3
5-4 Memory Support.............................................................................................. 5-4
Memory Population Guidelines ....................................................................... 5-4
Memory Installation Guidelines ...................................................................... 5-5
Installing DIMM Memory Modules................................................................... 5-5
5-5 Expansion Cards............................................................................................. 5-5
5-6 Motherboard Details........................................................................................ 5-6
5-7 Connector Denitions ..................................................................................... 5-9
Power Connectors ......................................................................................... 5-9
Other Motherboard Connectors .................................................................... 5-13
5-8 Jumper Settings ............................................................................................ 5-16
5-9 Onboard Indicators........................................................................................ 5-20
5-10 SATA Ports .................................................................................................... 5-21
5-11 Installing Software......................................................................................... 5-22
SuperDoctor®5 ............................................................................................. 5-23
5-12 Serverboard Battery...................................................................................... 5-24

vi
SUPERSERVER 5018D-FN8T Manual
Chapter 6 Advanced Chassis Setup and Maintenance
6-1 Static-Sensitive Devices.................................................................................. 6-1
Precautions ..................................................................................................... 6-1
6-2 Removing Power from the System ................................................................. 6-2
6-3 Removing the Chassis Cover ......................................................................... 6-3
6-4 Installing Hard Drives
Installing 3.5" Fixed Hard Drives .................................................................... 6-5
Installing 2.5" Fixed Hard Drives .................................................................... 6-5
6-5 Installing an Expansion Card .......................................................................... 6-6
6-6 System Fans ................................................................................................... 6-7
Checking the Chassis Airow.......................................................................... 6-8
6-7 Power Supply.................................................................................................. 6-8
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
Starting BIOS Setup Utility.............................................................................. 7-1
How To Change the Conguration Data ......................................................... 7-1
7-2 Main Setup...................................................................................................... 7-2
Starting the Setup Utility ................................................................................. 7-2
7-3 Advanced Setup Congurations...................................................................... 7-4
7-4 Event Logs .................................................................................................... 7-28
7-5 IPMI............................................................................................................... 7-30
7-6 Security Settings ........................................................................................... 7-32
7-7 Boot Settings................................................................................................. 7-35
7-8 Save & Exit ................................................................................................... 7-37
Appendix A BIOS POST Error Codes
Appendix B UEFI BIOS Recovery Instructions
Appendix C System Specications

vii
Contents
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Web Site: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Web Site: www.supermicro.com.tw

viii
SUPERSERVER 5018D-FN8T Manual
Notes

Chapter 1
Introduction
1-1 Overview
The SuperServer 5018D-FN8T is a compact, low-power network appliance
comprised of two main subsystems: the SC505-203B 1U server chassis and the
X10SDV-TP8F single processor motherboard. Certied operating systems are listed
at www.supermicro.com.
In addition to the motherboard and chassis, various hardware components are
listed below:
• One riser card (RSC-RR1U-E8) and bracket for a PCI expansion card
• Cooling: One 4-cm fan (FAN-0065L4)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
• Product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: ftp://ftp.supermicro.com
• Product safety information:
http://www.supermicro.com/about/policies/safety_information.cfm
For support, email [email protected].
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 5018D-FN8T User's Manual
1-2 Motherboard Features
The SuperServer 5018D-FN8T is built around the X10SDV-TP8F, a single processor
motherboard designed to provide maximum performance. Below are the main
features. (see Figure 1-1 for a block diagram)
Processors
The motherboard supports a single Intel Xeon D-1518 four Core 35W embedded
processor.
Memory
The motherboard has four DDR4 slots that can support up to 128 GB of ECC RDIMM
or 64GB ECC/Non-ECC UDIMM with a max data rate of 2133MHz.
Serial ATA
The system supports up to four SATA3 (6Gbps) 2.5" hard drives or one 3.5" drive.
It also includes one SATA DOM (Disk on Module) power connector.
Input/Output Ports
Externallly accessable ports include eight LAN ports--six RJ-45 at 1GbE speed,
and two SFP+ 10GbE, plus a dedicated IPMI LAN port. The system also offers two
USB 3.0 ports, and a VGA port.
The motherboard includes four USB 2.0, one USB Type-A header, and a serial
port header.
PCI Expansion Slots
The motherboard supports:
• One M.2 PCIe 3.0 x4 Slot, M Key for SSD, SATA 3.0 support (Mux with I-SATA4)
• One Mini PCIe 2.0 x1 slot with mSATA support (Mux with I-SATA5)

Chapter 1: Introduction
1-3
Figure 1-1. System Block Diagram
Note: This is a general block diagram. Refer to Chapter 5 for details.
LPC
USB
PROCESSOR
PCI-E 2.0
USB 3.0
SOC
USB 2.0
JPCIE1 PCIE 3.0 x8
DDR4 DIMM
B1
DDR4 DIMM
A2
A
B
A1
DDR4 DIMM
A
DDR4 DIMM
B1
B
PCIE 3.0 x8
SATA Gen3
USB HUB
GL854G
USB 3.0 connector x2
(compatible with 2.0)
USB 2.0 Header x2
iXFI
x2
x1
VGA
USB3.01G LANSFP+
USB 2.0 Header x2
3rd LAN
+
KR
DDR4 1600/1866/2133
USB 2.0 TypeA
INPHI CS4227
SFP+
JPCIE2 PCIE 3.0 x8
PCIE 3.0 x8
mini PCIe
PCIE 2.0 x1
PCIE 3.0 x3
M.2 CONN
PCIE 3.0 x3
LSI SAS2116
MINI-SAS HD
SAS2
SATA GEN 3
PCIE 2.0
SATA3.0#4SATA3.0#5
SATA3.0#0 SATA3.0#1 SATA3.0#2 SATA3.0#3
PCIE 2.0 x1
x1
COM1
DDR 3
BMC
AST2400
PHY
RTL8211F
VGA
CONN
IPMI LAN
SPI
FLASH
LAN I210
PCIE 2.0 x1
PCIE 2.0 x1
LAN I210
PCIE 2.0 x4
LAN I350
JLAN1
JLAN2JLAN3
1G LAN1G LAN
REAR IO
Front I/O

1-4
SUPERSERVER 5018D-FN8T User's Manual
1-3 Server Chassis Features
The appliance 5018D-FN8T is built on the SC505-203B, a small form factor 1U
rackmount server chassis. The following is a general outline of the main features.
System Power
The system has a single 200 watt low-noise AC-DC power supply with PFC.
Drives
The chassis is designed to support xed internal hard drives or SSDs--up to two
3.5" or up to four 2.5" drives. SATA DOM is also supported.
Control Panel
The control panel provides system monitoring and power control. LEDs indicate
power on, network activity, hard disk drive activity and system overheat. The control
panel also includes a main power button and a reset button.
PCI Expansion
The chassis provides one front PCI-E expansion card slot. If the server is congured
with one 3.5" drive (low prole) or two 2.5" drives (full height), it accepts an
expansion card. If the server is congured with four 2.5" drives, there is no room
for an expansion card.
Cooling System
The chassis has includes one 4-cm fan, and supports up to three fans. Fan speed
may be controlled using IPMI.

Chapter 1: Introduction
1-5
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.supermicro.com.tw

1-6
SUPERSERVER 5018D-FN8T User's Manual
Notes

Chapter 2
Installation in a Rack
This chapter provides instructions for mounting your chassis in a rack.
2-1 Preparing for Setup
The box in which your system was shipped should include the mounting screws
to mount the system into the rack. Please read this chapter in its entirety before
beginning the installation procedure.
Choosing a Setup Location
Decide on a suitable location for the rack unit that will hold your system. It should
be a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical
noise and electromagnetic elds are generated. A nearby grounded power outlet.
is required
• Leave at least 25 inches clearance in front of the rack to open the front door
completely.
• Leave approximately 30 inches of clearance in the back of the rack to allow for
sufcient airow and access for servicing.
• It should be a restricted access location, such as a dedicated equipment room
or a service closet.
Chapter 2: Installation in a Rack
2-1

SUPERSERVER 5018D-FN8T User's Manual
2-2
2-2 Warnings and Precautions
Rack Precautions
• Ensure that the leveling jacks on the bottom of the rack are fully extended to
the oor with the full weight of the rack resting on them.
• In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
• Always make sure the rack is stable before extending a component from the
rack.
• You should extend only one component at a time - extending two or more
simultaneously may cause the rack to become unstable.
Server Precautions
• Review the electrical and general safety precautions in Chapter 4.
• Determine the placement of each component in the rack before you install the
rails.
• Install the heaviest server components on the bottom of the rack rst, and then
work up.
• Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
• Allow the hot plug SAS drives and power supply modules to cool before touching
them.
• Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.

2-3
Chapter 2 Installation in a Rack
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient temperature
of the room. Therefore, consideration should be given to installing the equipment
in an environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).
Reduced Airow
Equipment should be mounted into a rack so that the amount of airow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power supply
connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).
To prevent bodily injury when mounting or servicing this unit in a rack, you
must take special precautions to ensure that the system remains stable.
The following guidelines are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit
in the rack.
• When mounting this unit in a partially lled rack, load the rack from the
bottom to the top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
• Slide rail mounted equipment is not to be used as a shelf or a work space.

SUPERSERVER 5018D-FN8T User's Manual
2-4
2-3 Installing the System into a Rack
The system can be installed into a rack directly using screws.
Installing the Chassis into a Rack
1. Find the four included mounting screws required to mount the chassis into a rack.
2. Align the mounting holes of the chassis with the thru-holes of the rack.
3. Insert the mounting screws into the thru-holes in the front of the chassis and
through the thru-holes in the rack
Figure 2-1. Installing the Chassis into a Rack
Note: Figures are for illustrative purposes only. Always install servers into racks
from the bottom up.
Warning: Do not pick up the server by the front handles. They are designed
to pull the system from a rack only.
Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the oor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.

3-1
Chapter 3 System Interface
Chapter 3
System Interface
3-1 Overview
The chassis includes a control panel on the front that includes power buttons and
status monitoring lights, and status lights for the power supply
Figure 3-1. Control Panel

SUPERSERVER 5018D-FN8T User's Manual
3-2
3-3 Control Panel LEDs
There are ve LEDs that provide status information about the system.
Power: The main power switch is used to apply or remove power from the power
supply to the server. Turning off system power with this button removes the main
power but maintains standby power. To perform many maintenance tasks, you must
unplug system before servicing.
Reset: The reset button is used to reboot the system.
NIC2: Indicates network activity on GLAN2 when ashing.
Information LED: Alerts operator of several states, as noted in the table below.
Information LED
Status Description
Continuously on and red An overheat condition has occured.
(This may be caused by cable congestion.)
Blinking red (1Hz) Fan failure, check for an inoperative fan.
Blinking red (0.25Hz) Power failure, check for a non-operational power supply.
Solid blue Local UID has been activated. Use this function to locate
the server in a rack mount environment.
Blinking blue Remote UID is on. Use this function to identify the
server from a remote location.
3-2 Control Panel Buttons
The chassis includes two push-buttons that control power to the system.