Supermicro SuperServer 5019P-MT User manual

USER'S MANUAL
Revision 1.0
SuperServer®
5019P-MT
5019P-MTR
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes
no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update
or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note:
For the most up-to-date version of this manual, please see our website at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual
at any time and without notice. This product, including software and documentation, is the property of Supermicro and/
or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except
as expressly permitted by the terms of said license.
IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIALDAMAGESARISING FROM THE USE OR INABILITYTO USE THIS PRODUCT
OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER
MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the
State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution
of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual,
may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only
to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate”.
WARNING: Handling of lead solder materials used in this product may expose you to lead, a
chemical known to the State of California to cause birth defects and other reproductive harm.
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment,
nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical

property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products
for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully
indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Manual Revision 1.0
Release Date: May 05, 2017
Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this

to herein are trademarks or registered trademarks of their respective companies or mark holders.
Copyright © 2017 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
Проконсультироваться икупить данное оборудование вы можете вкомпании «АНД-Системс»
адрес: 125480, г.Москва, ул.Туристская, д.33/1; site: https://andpro.ru тел: [phone] email: [email protected]
При обращении используйте промокод AND-PDF иполучите скидку.

43
PrefaceSuperServer 5019P-MT/MTR User's Manual
Preface
About this Manual
This manual is written for professional system integrators and PC technicians. It provides
information for the installation and use of the SuperServer 5019P-MT/MTR. Installation and
maintenance should be performed by experienced technicians only.

supported memory, processors and operating systems (http://www.supermicro.com).
Notes
For your system to work properly, please follow the links below to download all necessary
drivers/utilities and the user’s manual for your server.
• Supermicro product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: ftp://ftp.supermicro.com
• Product safety info: http://www.supermicro.com/about/policies/safety_information.cfm
If you have any questions, please contact our support team at:
[email protected]
This manual may be periodically updated without notice. Please check the Supermicro website
for possible updates to the manual revision level.
Warnings
Special attention should be given to the following symbols used in this manual.
Warning! Indicates high voltage may be encountered when performing a procedure.
Warning! Indicates important information given to prevent equipment/property damage

Contents
Chapter 1 Introduction
1.1 Overview...............................................................................................................................8
1.2 Unpacking the System .........................................................................................................8
1.3 System Features ..................................................................................................................9
1.4 Server Chassis Features....................................................................................................10
Control Panel ....................................................................................................................10
Front Features...................................................................................................................11
Rear Features ...................................................................................................................12
1.5 Motherboard Layout ...........................................................................................................13
Quick Reference Table......................................................................................................14
Chapter 2 Server Installation
2.1 Overview.............................................................................................................................17
2.2 Preparing for Setup ............................................................................................................17
Choosing a Setup Location...............................................................................................17
Rack Precautions ..............................................................................................................17
Server Precautions............................................................................................................18
Rack Mounting Considerations .........................................................................................18
Ambient Operating Temperature....................................................................................18
 ............................................................................................................................18
Mechanical Loading.......................................................................................................18
Circuit Overloading ........................................................................................................19
Reliable Ground.............................................................................................................19
2.3 Installing the Rails..............................................................................................................20
Identifying the Rails...........................................................................................................20
Installing the Rack Rails ...................................................................................................20
2.4 Installing the Server into a Rack........................................................................................21
Installing the Server into a Telco Rack .............................................................................22
Chapter 3 Maintenance and Component Installation
3.1 Removing Power ................................................................................................................23
3.2 Accessing the System........................................................................................................23

65
PrefaceSuperServer 5019P-MT/MTR User's Manual
3.3 Motherboard Components..................................................................................................24
Processor and Heatsink Installation..................................................................................24
Overview of the Processor Socket Assembly................................................................25
Overview of the Processor Heatsink Module (PHM) ........................................................26
Attaching the Non-F Model Processor to the Processor Clip to Create the Processor
Carrier Assembly...............................................................................................................27
Attaching the Non-F Model Processor Carrier Assembly to the Heatsink to Form the
Processor Heatsink Module (PHM)...................................................................................28
Preparing the CPU Socket for Installation........................................................................29
Removing the Dust Cover from the CPU Socket .............................................................29
Installing the Processor Heatsink Module (PHM) ............................................................30
Removing the Processor Heatsink Module (PHM) from the Motherboard .......................31
Memory Support and Installation ......................................................................................32
Memory Support ............................................................................................................32
DIMM Module Population Sequence ................................................................................33
DIMM Installation ..............................................................................................................34
DIMM Removal .................................................................................................................34
PCI Expansion Card Installation .......................................................................................35
3.4 Chassis Components .........................................................................................................36
Front Bezel........................................................................................................................36
Motherboard Battery .........................................................................................................37
Hard Drives .......................................................................................................................38
Hard Drive Carrier Indicators.........................................................................................39
DVD-ROM Drive Installation .............................................................................................40
System Cooling .................................................................................................................41
Replacing a Failed Fan .................................................................................................41
Power Supply: 5019P-MT .................................................................................................43
Power Supply Failure ....................................................................................................43
Power Supply: 5019P-MTR...............................................................................................43
Power Supply Failure ....................................................................................................43
Chapter 4 Motherboard Connections
4.1 Power Connections ............................................................................................................45
4.2 Headers and Connectors ...................................................................................................46
4.3 Front Control Panel ............................................................................................................51
4.4 Ports ...................................................................................................................................54
Rear I/O Ports................................................................................................................54
4.5 Jumpers..............................................................................................................................57
Explanation of Jumpers.................................................................................................57
4.6 LED Indicators....................................................................................................................59
Chapter 5 Software
5.1 OS Installation....................................................................................................................61
Installing the Windows OS for a RAID System ................................................................61
Installing Windows to a Non-RAID System ......................................................................61
5.2 Driver Installation................................................................................................................62
5.3 SuperDoctor®5...................................................................................................................63
5.4 IPMI ....................................................................................................................................64
Chapter 6 BIOS
6.1 Introduction.........................................................................................................................65
6.2 Main Setup .........................................................................................................................66
 .........................................................................................67
6.4 Event Logs .........................................................................................................................94
6.5 IPMI ................................................................................................................................... 96
6.6 Security...............................................................................................................................99
6.7 Boot ..................................................................................................................................103
6.8 Save & Exit.......................................................................................................................106
Appendix A BIOS Error Codes
Appendix BStandardized Warning Statements for AC Systems
Appendix C System Specications
Appendix D UEFI BIOS Recovery

7
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.supermicro.com.tw
SuperServer 5019P-MT/MTR User's Manual

98
SuperServer 5019P-MT/MTR User's Manual Chapter 1: Introduction
1.2 Unpacking the System
Inspect the box the SuperServer 5019P-MT/MTR was shipped in and note if it was damaged

who delivered it.
Decide on a suitable location for the rack unit that will hold the server. It should be situated
in a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical noise and

Be sure to read the precautions and considerations noted in Appendix B.
Main Parts List
Description Part Number Quantity
Air Shroud MCP-310-19007-0N 1
1U 4-Port 12Gbps Backplane Support 4x3.5" SAS/SAS HDD/SSD BPN-SAS3-815TQ 1
1U Passive CPU Heat Sink SNK-P0067P 1
Riser Card with PCI-E x16 output RSC-RR1U-E16 1
Set of four SATA 56/45.5/35/23CM round S-RA. 26AWG cables CBL-0186L 1
8-pin to 8-pin round SGPIO cable, 40cm, 28AWG, pinout 1-1 cable CBL-CDAT-0661 1
40 x 40 x 28-mm fans FAN-154L4 4
1.3 System Features
The following table provides you with an overview of the main features of the 5019P-MT/MTR.

System Features
Motherboard
5019P-MT/MTR
Chassis
5019P-MT: SC813MFTQC-350B
5019P-MTR: SC813MFTQC-R407CB
CPU
Supports an Intel Xeon 81xx/61xx/51xx/41xx/31xx series (Socket P0-LGA3647) processor with a thermal design
power (TDP) of up to 205W and 28 cores
Note: The X11SPi-TF motherboard does not support FPGA or Fabric processors.
Socket Type
Socket P0-LGA3647
Memory
Up to 256 GB of RDIMM, 512 GB of LRDIMM, and 1 TB of 3DS LRDIMM DDR4 ECC memory with speeds of
up to 2666 MHz and up to 128 GB size at 1.2V
Note: Memory speed support depends on the processors used in the system.
Chipset
Intel PCH C622
Expansion Slots
One (1) PCI Express 3.0 x16 slot (CPU SLOT6)
One (1) M.2 PCI Express 3.0 x4 slot (supports M-Key 2280 and 22110)
Hard Drives
Four (4) hot-swap 3.5" SATA hard drives
Power
5019P-MT: single 350 Watts power supply
5019P-MTR: dual 400 Watts power supply
Form Factor
1U rackmount
Dimensions
(WxHxD) 17.2 x 1.7 x 19.85 in. (437 x 43 x 504 mm)
Chapter 1
Introduction
1.1 Overview
This chapter provides a brief outline of the functions and features of the 5019P-MT/MTR. The
5019P-MT/MTR is based on the X11SPi-TF motherboard and the SC813MFTQC-350B/R407CB
chassis. The only difference between the two systems is their power supplies. The 5019P-MT
comes with a single 350 Watts power supply, while the 5019P-MTR comes equipped with
dual 400 Watts power supplies.
In addition to the motherboard and chassis, several important parts that are included with
the system are listed below:

1110
SuperServer 5019P-MT/MTR User's Manual Chapter 1: Introduction
1.4 Server Chassis Features
Control Panel
The switches and LEDs located on the control panel are described below. See Chapter 4 for
details on the control panel connections.
Front Features
The SC813MFTQC-350B/R407CB is a mini 1U chassis See the illustration below for the
features included on the front of the chassis.
Figure 1-1. Control Panel View
1 765432
Control Panel Features
Item Feature Description
1Universal Information LED See the following table for the status shown by this LED.
2NIC2 LED 
3NIC1 LED 
4HDD LED 
5Power LED Indicates power is being supplied to the system power supply. This LED should
normally be illuminated when the system is operating.
6Reset Button The reset button is used to reboot the system
7Power Button
The main power button is used to apply or remove power from the power supply
to the server. Turning off system power with this button removes the main power
but maintains standby power. To perform many maintenance tasks, you must
also unplug system before servicing
Universal Information LED
Status Description
Continuously on and red An overheat condition has occurred. (This may be caused by cable
congestion.)
Blinking red (1 Hz) Fan failure: check for an inoperative fan.
Blinking red (0.25 Hz) Power failure: check for an inoperative power supply.
Solid blue Local UID has been activated. Use this function to locate the server in a rack
environment.
Blinking blue (300 msec) Remote UID has been activated. Use this function to locate the server from a
remote location.
Front Chassis Features
Item Feature Description
1SATA HDD Hot-swap 3.5" SATA hard disk drive
2DVD Drive Front access DVD drive bay
3Front USB 3.0 and COM
Port A front control panel for two USB 3.0 ports and a COM port is positioned here.
4Control Panel Front control panel with LEDs and buttons (see preceding page)
5Rack Ear Brackets Attaches server chassis to the rack
Figure 1-2. Chassis Front View
1
5 5
4
3
2
1 11

1312
SuperServer 5019P-MT/MTR User's Manual Chapter 1: Introduction
SAN MAC
DESIGNED IN USA
BIOS LICENSE
X11SPi-TF
REV:1.02
IPMI CODE
MAC CODE
BAR CODE
JTPM1
JPWR1
MH11
MH10
JRK1
BT1
SP1
+
LEDBMC
LE3
LEDPWR
C
JL1
JOH1
JBT1
JSTBY1
JSD1
JSD2
JVRM1
JWD1
JPG1
JPME2
JIPMB1
JNVI2C1
FAN4 FAN3 FAN2 FAN1
FANA
FANB
FAN5
JPI2C1
JD1
I-SGPIO2
S-SGPIO1
I-SGPIO1
I-SATA4
I-SATA5
I-SATA6
I-SATA7
I-SATA0
S-SATA0
S-SATA1
I-SATA1
I-SATA2
I-SATA3
JF1
JPWR2
M.2 PCI-E 3.0 X4
USB10(3.0)
USB8/9(3.0)
USB6/7(3.0)
USB4/5
USB2/3
COM1
COM2
USB0/1
IPMI_LAN
LAN1
LAN2
VGA
UID-SW
UID-LED
PCH SLOT1 PCI-E 3.0 X4(IN X8)
CPU SLOT2 PCI-E 3.0 X8
CPU SLOT3 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X16
CPU SLOT6 PCI-E 3.0 X16
CPU
DIMMF1 DIMME1
DIMMD1 DIMMD2
DIMMA2
DIMMA1
DIMMB1
RST
JF1
ON PWR UID
LED
PS
FAIL 1
NIC
2
NIC NMIX
PWRHDD LEDLED
Intel
C622
ASpeed
AST2500
JPTG1
Intel
X557
DIMMC1
Rear Features
The illustration below shows the features included on the rear of the chassis.
Rear Chassis Features
Item Feature Description
1Power Supply* Single 350 Watts Platinum Level power supply for the 5019P-MT (PWS-350-1H), or
dual 400 Watts Platinum Level power supplies for the 5019P-MTR (PWS-407P-1R)
2I/O Backpanel Rear I/O ports (see Section 4.3 for full details)
3Expansion Card Slot Slot for one expansion card (requires pre-installed riser card)
4Rack Ear Brackets Attaches server chassis to the rack
*Note: The 5019P-MTR features redundant power (dual power supplies).
Figure 1-3. Chassis Rear View
1 44 3 2
Figure 1-4. Motherboard Layout
IPMI_LAN
USB0/1
USB10 (3.0)
LAN1
USB6/7 (3.0)
LAN2
COM1
VGA
UID LED
JIPMB1
FAN5
JSTBY1
FAN1
JPWR1
JPI2C1
FAN2
FAN3
I-SATA4
USB8/9 (3.0)
DIMMC1
DIMMA2
DIMMB1
DIMMA1
JF1
FANA
JPG1
JBT1
JOH1
USB2/3
JD1
I-SATA3
I-SATA2
JL1
USB4/5
JSD1
S-SATA1
I-SGPIO2
JPME2
JPWR2
JVRM1
JSD2
I-SATA1
I-SATA0
LEDBMC MH11
UID SW
JRK1
MH10
SLOT6
DIMMD2
DIMMF1
DIMMD1
DIMME1
FAN4 JNVI2C1
SLOT4
SLOT3
SLOT2
COM2
SP1
SLOT1
JWD1
I-SGPIO1
I-SATA7
I-SATA6
I-SATA5
LE3
FANB
LEDPWR
JTPM1
M.2
BT1
S-SGPIO1
S-SATA0
JPTG1
CPU
1.5 Motherboard Layout

the table on the following page for descriptions. For detailed descriptions, pinout information


1514
SuperServer 5019P-MT/MTR User's Manual Chapter 1: Introduction
Notes:
• -
tions.
• " " indicates the location of Pin 1.
• Jumpers/LED indicators not indicated are used for testing only.
• 
not install the onboard battery upside down to avoid possible explosion.
Quick Reference Table
Jumper Description Default Setting
JBT1 Clear CMOS Open (Normal)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPTG1 LAN Enable/Disable Pins 1-2 (Enabled)
JPME2 Manufacturing Mode Select Pins 1-2 (Normal)
JWD1 Watch Dog Enable Pins 1-2 (Reset)
LED Description Status
LE3 PCI-E 3.0 M.2 LED Green Blinking: Device Working
LEDBMC BMC Heartbeat LED Green Blinking: BMC Normal
LEDPWR Onboard Power LED Green Solid On: Power On
UID LED Rear UID LED 
Connector Description
BT1 Onboard Battery
COM1/COM2 COM Port/COM Header
FAN1 ~ FAN5, FANA/FANB CPU/System Fan Headers
IPMI LAN Dedicated IPMI LAN Port
I-SATA0 ~ I-SATA7 Intel® PCH SATA 3.0 Ports (with RAID 0, 1, 5, 10)
I-SGPIO1/I-SGPIO2/S-SGPIO1 Serial Link General Purpose I/O Connection Headers (I-SGPIO: SATA use; S-SGPIO: sSATA
use)
JD1 Speaker/Power LED Indicator (Pins 1-3: Power LED, Pins 4-7: Speaker)
JF1 Front Control Panel Header
JIPMB1 4-pin BMC External I2C Header (for an IPMI card)
JL1 Chassis Intrusion Header
JNVI2C1 NVMe I2C Header
JOH1 Overheat LED Indicator
JPI2C1 Power I2C System Management Bus (SMB) Header
JPWR1 8-pin Power Connector
Connector Description
JPWR2 24-pin ATX Power Connector
JRK1 Intel RAID Key Header
JSD1/JSD2 SATA DOM Power Connectors
JSTBY1 Standby Power Header
JTPM1 Trusted Platform Module/Port 80 Connector
JVRM1 VRM SMBus Header (for programming use)
LAN1/LAN2 LAN (RJ45) Ports
M.2 M.2 PCI-E 3.0 X4 Slot (Supports M-Key 2280 and 22110)
MH10/MH11 M.2 Mounting Holes
SLOT1 PCH PCI-E 3.0 X4 (IN X8) Slot
SLOT2 CPU PCI-E 3.0 X8 Slot
SLOT3/SLOT4 CPU PCI-E 3.0 X8/X16 Slot (Supports Auto Switch)
SLOT6 CPU PCI-E 3.0 X16 Slot
SP1 Internal Speaker/Buzzer
S-SATA0/S-SATA1 SATA 3.0 ports with SATA DOM Power
UID SW 
USB0/1 Back Panel Universal Serial Bus (USB) 2.0 Ports
USB2/3, USB4/5 Front Accessible USB 2.0 Headers
USB6/7 Back Panel USB 3.0 Ports
USB8/9 Front Accessible USB 3.0 Headers
USB10 USB 3.0 Type A Header
VGA VGA Port

16
SuperServer 5019P-MT/MTR User's Manual
Figure 1-5. Intel PCH C622 Chipset: System Block Diagram
Note: This is a general block diagram and may not exactly represent the features on your

motherboard.
SPI
LAN3
RGRMII
FRONT PANEL
SYSTEM POWER
CTRL
FAN SPEED
PCI-E X1 G2
USB 2.0
#6 USB2.0
KR
Intel
C622
USB 2.0
USB
RTL8211E-VB-CG
RJ45
Temp Sensor
EMC1402-1 *2 at diff SMBUS
USB 3.0
USB
SPI
AST2500
BMC
#8~11
#5
COM1
Connector COM2 Header
VGA CONN
BMC Boot Flash
DDR4
SLOT 2
5+1 PHASE
145W
2133/2666
DDRIV
VR13
#C-1
#B-1
#A-2
#A-1
SLOT 1
SLOT 3
PCI-E X8
PCI-E X8 G3
DMI3
PCI-E X8 G3
PCI-E X4 G3
DMI3
SNB CORE
DDR-IV
SLOT 4
PCI-E X16
PCI-E X16
SLOT 6
PCI-E X16 G3(X8 option)
#3B #3A #1B
VCCP0 12v
VCCP0
PECI:30
SOCKET ID:0
#1A
PCI-E X8
2133/2666
DDRIV
#F-1
#E-1
#D-2
#D-1
#0~3
PCIe
PCI-E X8
Uplink
PCI-E X8
#2
Front USB2.0 x 4
USB 2.0
USB
Rear USB2.0 x 2
USB2.0 #2,3
USB2.0 #4,5
USB2.0 #0,1
Front USB3.0 x 2
USB
USB
Type A USB3.0
Rear USB3.0 x 2
X557 (10G)
LAN
RMII/NCSI
KR
M.2 SSD
PCI-E X4 G3
PCI-E X16 G3
6.0 Gb/S
#1
#0
sSATA
SATA-DOM
6.0 Gb/S
#1
#0
SATA
#3
#2
#4
#5
#6
#7
Debug Card
TPM HEADER
BIOS
Switch
SWITCH
C622 X8 UPLINK
NO QAT 2*10G+2*1G(~17W)
(Also supports
SATA X1)
SPI

SuperServer 5019P-MT/MTR User's Manual Chapter 2: Server Installation
1817
Chapter 2
Server Installation
2.1 Overview
This chapter provides advice and instructions for mounting your system in a server rack.
If your system is not already fully integrated with processors, system memory etc., refer to

Caution: Electrostatic Discharge (ESD) can damage electronic components. To prevent such
damage to PCBs (printed circuit boards), it is important to use a grounded wrist strap, handle
all PCBs by their edges and keep them in anti-static bags when not in use.
2.2 Preparing for Setup
The box in which the system was shipped should include the rackmount hardware needed to
install it into the rack. Please read this section in its entirety before you begin the installation.
Choosing a Setup Location
•
The system should be situated in a clean, dust-free area that is well ventilated. Avoid areas

• Leave enough clearance in front of the rack so that you can open the front door completely
(~25 inches) and approximately 30 inches of clearance in the back of the rack to allow

• This product should be installed only in a Restricted Access Location (dedicated equipment
rooms, service closets, etc.).
• This product is not suitable for use with visual display workplace devices acccording to §2
of the the German Ordinance for Work with Visual Display Units.
Rack Precautions
•

the full weight of the rack rests on them.
• In single rack installations, stabilizers should be attached to the rack. In multiple rack in-
stallations, the racks should be coupled together.
• Always make sure the rack is stable before extending a server or other component from
the rack.
• You should extend only one server or component at a time - extending two or more simul-
taneously may cause the rack to become unstable.
Server Precautions
• Review the electrical and general safety precautions in Appendix B.
• Determine the placement of each component in the rack before you install the rails.
• 
way up.
• Use a regulating uninterruptible power supply (UPS) to protect the server from power
surges and voltage spikes and to keep your system operating in case of a power failure.
• Allow any drives and power supply modules to cool before touching them.
• When not servicing, always keep the front door of the rack and all covers/panels on the
servers closed to maintain proper cooling.
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of
the rack environment may be greater than the room's ambient temperature. Therefore,
consideration should be given to installing the equipment in an environment compatible with
the manufacturer’s maximum rated ambient temperature (TMRA).
Airow
               
operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not arise due
to uneven mechanical loading.

SuperServer 5019P-MT/MTR User's Manual Chapter 2: Server Installation
2019
Circuit Overloading
Consideration should be given to the connection of the equipment to the power supply circuitry
and the effect that any possible overloading of circuits might have on overcurrent protection
and power supply wiring. Appropriate consideration of equipment nameplate ratings should
be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself should be
grounded. Particular attention should be given to power supply connections other than the
direct connections to the branch circuit (i.e. the use of power strips, etc.).

special precautions to ensure that the system remains stable. The following guidelines
are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
• 
with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or
servicing the unit in the rack.
2.3 Installing the Rails
There are a variety of rack units on the market, which may require a slightly different assembly
procedure.
The following is a basic guideline for installing the system into a rack with the rack mounting
hardware provided. You should also refer to the installation instructions that came with the

Identifying the Rails
The rack rails and the related hardware should have been included with the system. Note

Installing the Rack Rails
Determine where you want to place the server in the rack (see the Rack and Server
Precautions in Section 2.2). Note that servers should always be installed to the bottom of a

1. Position the chassis rail guides at the desired location in the rack, keeping the sliding
rail guide facing the inside of the rack.
2. Screw the assembly securely to the rack using the brackets provided.
3. Attach the other assembly to the other side of the rack, making sure that both are at the
exact same height and with the rail guides facing inward.
Note: Both front chassis rails and the rack rails have a locking tab, which serves two functions.
First, it locks the server into place when installed and pushed fully into the rack (its normal
operating position. In addition, these tabs lock the server in place when fully extended from
the rack. This prevents the server from coming completely out of the rack when pulled out
for servicing.
Warning: do not pick up the server with the front handles. They are designed to pull
the system from a rack only.
Slide rail mounted equipment is not to be used as a shelf or a work space.

SuperServer 5019P-MT/MTR User's Manual Chapter 2: Server Installation
2221
2.4 Installing the Server into a Rack
You should now have rails attached to both the chassis and the rack. The next step is to
install the server into the rack.
1. Line up the rear of the chassis rails with the front of the rack rails.
2. Slide the chassis rails into the rack rails, keeping the pressure even on both sides (you
may have to press the locking tabs when inserting). See Figure 2-2.
3. When the server has been pushed completely into the rack, you should hear the locking
tabs "click".
Figure 2-1. Installing the Server into a Rack
Note: Figures are for illustrative purposes only. Always install servers to the bottom of a rack

Warning: Stability hazard. The rack stabilizing mechanism must be in place, or the

stabilize the rack can cause the rack to tip over.
Note: 
Installing the Server into a Telco Rack
To install the SuperServer 5019P-MT/MTR into a Telco (or “open”) type rack, use two L-shaped
brackets on either side of the chassis (four total).
1. First, determine how far the server will extend out from the front of the rack. The chassis
should be positioned so that the weight is balanced between front and back.
2. Attach the two front brackets to each side of the chassis, then the two rear brackets

3. Finish by sliding the chassis into the rack and tightening the brackets to the rack. See
Figure 2-4.
Figure 2-2. Installing the Server into a Telco Rack

SuperServer 5019P-MT/MTR User's Manual
2423
Chapter 3: Maintenance and Component Installation
Chapter 3
Maintenance and Component Installation
This chapter provides instructions on installing and replacing main system components. To

numbers given.

system. Please follow the procedures given in each section.
3.1 Removing Power
Use the following procedure to ensure that power has been removed from the system. This
step is necessary when removing or installing non hot-swap components.
1. Use the operating system to power down the system.
2. After the system has completely shut-down, disconnect the AC power cords from the
power strip or outlet. (If your system has more than one power supply, remove the AC
power cords from all power supply modules.)
3. Disconnect the power cord(s) from the power supply modules.
3.2 Accessing the System
The SC813MFTQC-350B/R407CB features a removable top cover, which allows easy access
to the inside of the chassis.
Removing the Top Cover
1. Begin by removing power from the system as described in Section 3.1.
2. Grasp the two handles on either side and pull the unit straight out until it locks (you will
hear a "click").
3. Depress the two buttons on the top of the chassis to release the top cover and at the
same time, push the cover away from you until it stops.
4. Lift the top cover from the chassis to gain full access to the inside of the server.
Warning: Except for short periods of time, do not operate the server without the cover in place.

3.3 Motherboard Components
Processor and Heatsink Installation
Warning: When handling the processor package, avoid placing direct pressure on the label
area of the CPU or CPU socket. Also, improper CPU installation or socket misalignment can
cause serious damage to the CPU or motherboard which may result in RMA repairs. Please
read and follow all instructions thoroughly before installing your CPU and heatsink.
Notes:
• Always connect the power cord last, and always remove it before adding, removing, or
changing any hardware components. Please note that the processor and heatsink should

the entire PHM into the CPU socket.
• When you receive a motherboard without a processor pre-installed, make sure that the
plastic CPU socket cap is in place and that none of the socket pins are bent; otherwise,
contact your retailer immediately.
• Refer to the Supermicro website for updates on CPU support.
• 
chapter before handling, installing, or removing system components.
Note: All graphics, drawings, and pictures shown in this manual are for illustration only. The
components that came with your machine may or may not look exactly the same as those
shown in this manual.

SuperServer 5019P-MT/MTR User's Manual
2625
Chapter 3: Maintenance and Component Installation
3. Dust Cover
4. CPU Socket
2. Processor Clip (the plastic processor package carrier used for the CPU)
Overview of the Processor Socket Assembly
The processor socket assembly contains 1) the Intel SKX processor, 2) the processor clip,
3) the dust cover, and 4) the CPU socket.
Note: Be sure to cover the CPU socket with the dust cover when the CPU is not installed.
1. Heatsink
2. Processor Clip
3. SKX Processor
Overview of the Processor Heatsink Module (PHM)
The Processor Heatsink Module (PHM) contains 1) a heatsink, 2) a processor clip, and 3)
the SKX processor.
(Bottom View for a non-F Model)
1. SKX Processor

SuperServer 5019P-MT/MTR User's Manual
2827
Chapter 3: Maintenance and Component Installation
Attaching the Non-F Model Processor to the Processor Clip to
Create the Processor Carrier Assembly
To properly install the CPU into the processor clip, please follow the steps below.
1. Locate pin 1 (notch A), which is the triangle located on the top of the processor clip.
Also locate notch B and notch C on the processor clip.
2. Locate pin 1 (notch A), which is the triangle on the substrate of the CPU. Also, locate
notch B and notch C on the CPU as shown below.
3. Align pin 1 (the triangle on the substrate) of the CPU with pin 1 (the triangle) of the
processor clip. Once they are aligned, carefully insert the CPU into the processor clip by
sliding notch B of the CPU into notch B of the processor clip, and sliding notch C of the
CPU into notch C of the processor clip.
4. Examine all corners of the CPU to ensure that it is properly seated on the processor
clip. Once the CPU is securely attached to the processor clip, the processor carrier
assembly is created.
Note: Please exercise extreme caution when handling the CPU. Do not touch the CPU
LGA-lands to avoid damaging the LGA-lands or the CPU. Be sure to wear ESD gloves when
handling components.
Processor Carrier Assembly (with CPU mounted
on the Processor Clip)
A
B
C
Allow Notch C to
latch on to CPU
Allow Notch B to
latch on to CPU
A
A
B
B
C
C
Pin 1
Align CPU Pin 1
CPU (Upside Down)
w/CPU LGA Lands up
CPU/Heatsink Package
(Upside Down)
Align Notch C of the CPU
and Notch C of the Processor Clip
Align Notch B of the CPU
and Notch B of the Processor Clip
Attaching the Non-F Model Processor Carrier Assembly to the
Heatsink to Form the Processor Heatsink Module (PHM)
After you have made a processor carrier assembly by following the instructions on the previous
page, please follow the steps below to mount the processor carrier assembly onto the heatsink
to create the Processor Heatsink Module (PHM).
1. Locate "1" on the heatsink label and the triangular corner next to it on the heatsink.

and turn the heatsink upside down with the thermal-grease side facing up. Remove the

as needed. (Skip this step if you have a new heatsink because the necessary thermal
grease is pre-applied in the factory.)
2. Holding the processor carrier assembly at the center edge, turn it upside down. With
the thermal-grease side facing up, locate the hollow triangle located at the corner of the
processor carrier assembly ("a" in the graphic). Note a larger hole and plastic mounting
clicks located next to the hollow triangle. Also locate another set of mounting clicks and
a larger hole at the diagonal corner of the same (reverse) side of the processor carrier
assembly ("b" in the graphic).
3. With the back of the heatsink
and the reverse side of the
processor carrier assembly facing
up, align the triangular corner on
the heatsink ("A" in the graphic)
against the mounting clips next
to the hollow triangle ("a") on the
processor carrier assembly.
4. Also align the triangular corner ("B")
at the diagonal side of the heatsink
with the corresponding clips on the
processor carrier assembly ("b").
5. Once the mounting clips on
the processor carrier assembly
are properly aligned with the
corresponding holes on the back
of the heatsink, securely attach the
heatsink to the processor carrier
assembly by snapping the mounting
clips at the proper places on the
heatsink to create the processor
heatsink module (PHM).
Heatsink
(Upside Down)
Non-Fabric CPU and Processor Clip
(Upside Down)
C
D
dc
a
b
A
B
On Locations of (C, D), the notches
snap onto the heat sink’s
mounting holes
On Locations (A, B), the notches
snap onto the heatsink’s sides
A
B
DC
Make sure Mounting
Notches snap into place
Triangle on the CPU
Triangle on the
Processor Clip

SuperServer 5019P-MT/MTR User's Manual
3029
Chapter 3: Maintenance and Component Installation
Note: Visit the product page on the Supermicro website for possible updates to memory
support (www.supermicro.com).
Preparing the CPU Socket for Installation
This motherboard comes with the CPU socket pre-assembled in the factory. The CPU socket
contains 1) a dust cover, 2) a socket bracket, 3) the CPU (P0) socket, and 4) a back plate.
These components are pre-installed on the motherboard before shipping.
Dusk Cover
SKX CPU Socket
Socket Pins
Remove the dust cover from
the CPU socket. Do not
touch the socket pins!
Removing the Dust Cover from the CPU Socket
Remove the dust cover from the CPU socket, exposing the SKX socket and socket pins as
shown on the illustration below.
Note: Do not touch the socket pins to avoid damaging them, causing the CPU to malfunction.
Installing the Processor Heatsink Module (PHM)
1. Once you have assembled the processor heatsink module (PHM) by following the
instructions listed on page 29, you are ready to install the processor heatsink module
(PHM) into the CPU socket on the motherboard. To install the PHM into the CPU socket,
follow the instructions below.
2. Locate the triangle (pin 1) on the CPU socket, and locate the triangle (pin 1) at the

turn the PHM upside down. With the LGA-lands side facing up, you will note the hollow
triangle located next to a screw at the corner. Turn the PHM right side up, and you will
see a triangle marked on the processor clip at the same corner of hollow triangle.)
3. Carefully align pin 1 (the triangle) on the the PHM against pin 1 (the triangle) on the
CPU socket.
4. Once they are properly aligned, insert the two diagonal oval holes on the heatsink into
the guiding posts.
5. Using a T30 Torx-bit screwdriver, install four screws into the mounting holes on the
socket to securely attach the PHM onto the motherboard starting with the screw marked
"1" (in the sequence of 1, 2, 3, and 4).
Note: Do not use excessive force when tightening the screws to avoid damaging the LGA-
lands and the processor.
#1 #2
#3
#4
Small Guiding Post
Large Guiding Post
Oval D
T30 Torx Driver
Use a torque
of 12 lbf
Oval C
Printed Triangle
Mounting the Processor Heatsink Module
into the CPU socket (on the motherboard)
Tighten the screws in the
sequence of 1, 2, 3, 4 (top 3 quarter view)
Figure 3-1. CPU Socket with Dust Cover Up
Figure 3-2. Removing the Dust Cover from the CPU Socket

SuperServer 5019P-MT/MTR User's Manual
3231
Chapter 3: Maintenance and Component Installation
Memory Support and Installation
Note: Check the Supermicro website for recommended memory modules.
Important: Exercise extreme care when installing or removing DIMM modules to prevent
any possible damage.
Memory Support
The X11SPi-TF supports up to 256 GB of RDIMM, 512 GB of LRDIMM, and 1 TB of 3DS
LRDMIMM DDR4 ECC memory with speeds of up to 2666 MHz in eight memory slots. Refer
to the table below for additional memory information.
Populating RDIMM/RDIMM 3DS/LRDIMM/LRDIMM 3DS DDR4 Memory Modules
Type Ranks Per DIMM and
Data Width
DIMM Capacity (GB)
Speed (MT/s); Voltage (V); Slots per Channel
(SPC) and DIMMs per Channel (DPC)
1 Slot per
Channel 2 Slots per Channel
1 DPC 1 DPC 1 DPC
4 GB 8 GB 1.2 V 1.2 V 1.2 V
RDIMM SRx4 8 GB 16 GB 2666 2666 2666
RDIMM SRx8 4 GB 8 GB 2666 2666 2666
RDIMM DRx8 8 GB 16 GB 2666 2666 2666
RDIMM DRx4 16 GB 32 GB 2666 2666 2666
RDIMM 3DS QRx4 NA 2H-64 GB 2666 2666 2666
8Rx4 NA 4H-128 GB 2666 2666 2666
LRDIMM 8Rx4 32 GB 64 GB 2666 2666 2666
LRDIMM 3DS QRx4 NA 2H-64 GB 2666 2666 2666
8Rx4 NA 4H-128 GB 2666 2666 2666
Printed Triangle on Motherboard
Removing the screws in
the sequence of 4, 3, 2, 1
#1 #2
#3
#4
After removing the screws,
lift the Processor Heatsink
Module off the CPU socket.
CPU Socket
Removing the Processor Heatsink Module (PHM) from the
Motherboard
Before removing the processor heatsink module (PHM), unplug power cord from the power
outlet.
1. Using a T30 Torx-bit screwdriver, turn the screws on the PHM counterclockwise to
loosen them from the socket, starting with the screw marked #4 (in the sequence of 4,
3, 2, 1).
2. After all four screws are removed, wiggle the PHM gently and pull it up to remove it
from the socket.
Note: To properly remove the processor heatsink module, be sure to loosen and remove the
screws on the PHM in the sequence of 4, 3, 2, 1 as shown below.

SuperServer 5019P-MT/MTR User's Manual
3433
Chapter 3: Maintenance and Component Installation
DIMM Module Population Sequence
When installing memory modules, the DIMM slots should be populated in the following order:
DIMMA1, DIMMD1, DIMMB1, DIMME1, then DIMMC1, DIMMF1, DIMMA2, DIMMD2.
• 
• Only populate DIMMA2 and DIMMD2 if the extra memory support is needed.
• Always use DDR4 DIMM modules of the same type, size and speed.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed of the
slowest DIMM.
• The motherboard will support odd-numbered modules (1 or 3 modules installed). However,
to achieve the best memory performance, a balanced memory population is recommended.
SAN MAC
DESIGNED IN USA
BIOS LICENSE
X11SPi-TF
REV:1.02
IPMI CODE
MAC CODE
BAR CODE
JTPM1
JPWR1
MH11
MH10
JRK1
BT1
SP1
+
LEDBMC
LE3
LEDPWR
C
JL1
JOH1
JBT1
JSTBY1
JSD1
JSD2
JVRM1
JWD1
JPG1
JPME2
JIPMB1
JNVI2C1
FAN4 FAN3 FAN2 FAN1
FANA
FANB
FAN5
JPI2C1
JD1
I-SGPIO2
S-SGPIO1
I-SGPIO1
I-SATA4
I-SATA5
I-SATA6
I-SATA7
I-SATA0
S-SATA0
S-SATA1
I-SATA1
I-SATA2
I-SATA3
JF1
JPWR2
M.2 PCI-E 3.0 X4
USB10(3.0)
USB8/9(3.0)
USB6/7(3.0)
USB4/5
USB2/3
COM1
COM2
USB0/1
IPMI_LAN
LAN1
LAN2
VGA
UID-SW
UID-LED
PCH SLOT1 PCI-E 3.0 X4(IN X8)
CPU SLOT2 PCI-E 3.0 X8
CPU SLOT3 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X16
CPU SLOT6 PCI-E 3.0 X16
CPU
DIMMF1 DIMME1
DIMMD1 DIMMD2
DIMMA2
DIMMA1
DIMMB1
RST
JF1
ON PWR UID
LED
PS
FAIL 1
NIC
2
NIC NMIX
PWRHDD LEDLED
Intel
C622
ASpeed
AST2500
JPTG1
Intel
X557
DIMMB1
DIMMA1
DIMMC1
DIMMD1
DIMMD2
DIMMA2
DIMME1
DIMMF1
SAN MAC
DESIGNED IN USA
BIOS LICENSE
X11SPi-TF
REV:1.02
IPMI CODE
MAC CODE
BAR CODE
JTPM1
JPWR1
MH11
MH10
JRK1
BT1
SP1
+
LEDBMC
LE3
LEDPWR C
JL1
JOH1
JBT1
JSTBY1
JSD1
JSD2
JVRM1
JWD1
JPG1
JPME2
JIPMB1
JNVI2C1
FAN4 FAN3 FAN2 FAN1
FANA
FANB
FAN5
JPI2C1
JD1
I-SGPIO2
S-SGPIO1
I-SGPIO1
I-SATA4
I-SATA5
I-SATA6
I-SATA7
I-SATA0
S-SATA0
S-SATA1
I-SATA1
I-SATA2
I-SATA3
JF1
JPWR2
M.2 PCI-E 3.0 X4
USB10(3.0)
USB8/9(3.0)
USB6/7(3.0)
USB4/5
USB2/3
COM1
COM2
USB0/1
IPMI_LAN
LAN1
LAN2
VGA
UID-SW
UID-LED
PCH SLOT1 PCI-E 3.0 X4(IN X8)
CPU SLOT2 PCI-E 3.0 X8
CPU SLOT3 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X16
CPU SLOT6 PCI-E 3.0 X16
CPU
DIMMF1 DIMME1
DIMMD1 DIMMD2
DIMMA2
DIMMA1
DIMMB1
RST
JF1
ON PWR UID
LED
PS
FAIL 1
NIC
2
NIC NMIX
PWRHDD LEDLED
Intel
C622
ASpeed
AST2500
JPTG1
Intel
X557
DIMM Installation
1. Insert the desired number of DIMMs into
the memory slots, starting with DIMMA1,
DIMMD1, DIMMB1, DIMME1, then
DIMMC1, DIMMF1, DIMMA2, DIMMD2. For
best performance, please use the memory
modules of the same type and speed.
2. Push the release tabs outwards on both
ends of the DIMM slot to unlock it.
3. Align the key of the DIMM module with the
receptive point on the memory slot.
4. Align the notches on both ends of the
module against the receptive points on the
ends of the slot.
5. Press the notches on both ends of the
module straight down into the slot until the
module snaps into place.
6. Press the release tabs to the lock positions
to secure the DIMM module into the slot.
DIMM Removal
Press both release tabs on the ends of the
DIMM module to unlock it. Once the DIMM
module is loosened, remove it from the memory
slot.
Release Tabs
Notches
Press both notches
straight down into
the memory slot.
Figure 3-3. DIMM Numbering

SuperServer 5019P-MT/MTR User's Manual
3635
Chapter 3: Maintenance and Component Installation
PCI Expansion Card Installation
The system includes one pre-installed riser card: RSC-RR1U-E16, for a standard size PCI-E
x16 card. Riser cards position the expansion cards at a 90 degree angle, allowing them to

Installing PCI Expansion Cards
The riser card has already been pre-installed into the motherboard. Perform the following
steps to install an add-on card:
Begin by removing power from the system as described in section 3.1.
1. Remove the chassis cover to access the inside of the system.
2. Remove the PCI slot shield on the chassis by releasing the locking tab.
3. Insert the expansion (add-on) card into the riser card.
4. Secure the card with the locking tab.
3.4 Chassis Components
Front Bezel
If your system has an optional bezel attached to the front of the chassis, you will need to
remove it to gain access to the drive bays.
1. Unlock the front of the chassis and then press the release knob.
2. 
removed for replacement/cleaning.



SuperServer 5019P-MT/MTR User's Manual
3837
Chapter 3: Maintenance and Component Installation
Warning: There is a danger of explosion if the onboard battery is installed upside down (which
reverses its polarities). This battery must be replaced only with the same or an equivalent type
recommended by the manufacturer (CR2032).
OR
Figure 3-3. Installing the Onboard Battery
Motherboard Battery
The motherboard uses non-volatile memory to retain system information when system power
is removed. This memory is powered by a lithium battery residing on the motherboard.
Replacing the Battery
Begin by removing power from the system as described in section 3.1.
1. Push aside the small clamp that covers the edge of the battery. When the battery is
released, lift it out of the holder.
2. To insert a new battery, slide one edge under the lip of the holder with the positive (+)
side facing up. Then push the other side down until the clamp snaps over it.
Note: Handle used batteries carefully. Do not damage the battery in any way; a damaged
battery may release hazardous materials into the environment. Do not discard a used battery

hazardous waste management agency to dispose of your used battery properly.
Hard Drives
Your server may or may not have come with hard drives installed. Up to four 3.5" hard drives
are supported by the chassis.
SATA drives are mounted in drive carriers to simplify their installation and removal from the
chassis. (Both procedures may be done without removing power from the system.)
Removing a Hot-Swap Drive Carrier
1. Push the release button on the carrier.
2. Swing the handle fully out.
3. Grasp the handle and use it to pull the drive carrier out of its bay.
Mounting a Drive in a Drive Carrier
1. To add a new drive, install it into the carrier with the printed circuit board side facing
down so that the mounting holes align with those in the carrier.
2. Secure the drive to the carrier with the screws provided, then push the carrier
completely into the drive bay. You should hear a *click* when the drive is fully inserted.
This indicates that the carrier has been fully seated and connected to the midplane,
which automatically makes the power and logic connections to the hard drive.
Figure 3-4. Mounting a Drive in a Carrier