Supermicro SuperServer 6048R-TXR User manual

SUPERSERVER®
6048R-TXR
USER’S MANUAL
1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0
Release Date: April 7, 2015
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2015 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 6048R-TXR
server. Installation and maintenance should be performed by experienced
technicians only.
The SuperServer 6048R-TXR is based on the SC842XTQ-R606B 4U rackmount
server chassis and the Super X10DRX serverboard. Please refer to our website for
an up-to-date list of supported operating systems, processors and memory.
Manual Organization
Chapter 1: Introduction
The rst chapter provides a checklist of the main components included with the
server system and describes the main features of the Super X10DRX serverboard
and the SC842XTQ-R606B chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the system into a rack and
check out the server conguration prior to powering up the system. If your server
was ordered without the processor and memory components, this chapter will refer
you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer to this chapter for details on the system interface, which includes the functions
and information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
system.
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X10DRX serverboard, including the
locations and functions of connectors, headers and jumpers. Refer to this chapter
when adding or removing processors or main memory and when reconguring the
serverboard.
iii
Preface

SUPERSERVER 6048R-TXR User's Manual
iv
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC842XTQ-R606B server chassis.
You should follow the procedures given in this chapter when installing, removing or
reconguring SATA or peripheral drives and when replacing system power supply
units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed information
on running the CMOS Setup Utility.
Appendix A: BIOS POST Messages
Appendix B: System Specications

v
Preface
Notes

vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Serverboard Features ..................................................................................... 1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
Serial ATA ....................................................................................................... 1-2
PCI Expansion Slots ....................................................................................... 1-2
Rear I/O Ports................................................................................................. 1-2
IPMI................................................................................................................. 1-2
1-3 Server Chassis Features ................................................................................ 1-3
System Power................................................................................................. 1-3
SATA Subsystem............................................................................................. 1-3
Front Control Panel......................................................................................... 1-3
Cooling System............................................................................................... 1-3
1-4 Contacting Supermicro.................................................................................... 1-5
Chapter 2 Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System .................................................................................... 2-1
2-3 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-1
2-4 Warnings and Precautions.............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations ....................................................................... 2-3
Ambient Operating Temperature ................................................................ 2-3
Reduced Airow ......................................................................................... 2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-3
2-5 Installing the System into a Rack ................................................................... 2-4
Mounting the Chassis in an Open (Telco) Style Rack.................................... 2-4
Rail System Overview..................................................................................... 2-5
Separating the Sections of the Rack Rails..................................................... 2-5
Installing the Inner Rails ................................................................................. 2-6
Outer Rack Rails............................................................................................. 2-7
Chapter 3 System Interface
3-1 Overview ......................................................................................................... 3-1
SUPERSERVER 6048R-TXR User's Manual

vii
Table of Contents
3-2 Control Panel Buttons ..................................................................................... 3-1
Reset............................................................................................................... 3-1
Power .............................................................................................................. 3-1
3-3 Control Panel LEDs ........................................................................................ 3-2
Power Fail ....................................................................................................... 3-2
Information LED .............................................................................................. 3-2
NIC1 ................................................................................................................ 3-2
NIC2 ................................................................................................................ 3-2
HDD................................................................................................................. 3-3
Power .............................................................................................................. 3-3
3-4 Drive Carrier LEDs.......................................................................................... 3-3
Chapter 4 Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements....................................................... 4-1
Warning Denition ........................................................................................... 4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning ........................................................................ 4-6
Equipment Installation..................................................................................... 4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................ 4-13
Comply with Local and National Electrical Codes........................................ 4-14
Product Disposal........................................................................................... 4-15
Hot Swap Fan Warning................................................................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard ............................................................................... 5-1
Precautions ..................................................................................................... 5-1
5-2 Connecting Cables.......................................................................................... 5-2
Connecting Data Cables ................................................................................. 5-2
Connecting Power Cables .............................................................................. 5-2
Connecting the Control Panel......................................................................... 5-2
5-3 I/O Ports.......................................................................................................... 5-3
5-4 Installing the Processor and Heatsink ............................................................ 5-4
Installing an LGA 2011 Processor................................................................... 5-4
Installing a CPU Heatsink ............................................................................... 5-7
Removing the Heatsink................................................................................... 5-8
5-6 Installing Memory............................................................................................ 5-9

viii
Memory Support....................................................................................... 5-10
5-6 Adding PCI Add-On Cards.............................................................................5-11
5-7 Serverboard Details ...................................................................................... 5-13
X10DRX Quick Reference ............................................................................ 5-13
5-8 Connector Denitions.................................................................................... 5-15
5-9 Jumper Settings ............................................................................................ 5-21
5-10 Onboard Indicators........................................................................................ 5-23
5-11 SATA Ports .................................................................................................... 5-24
5-12 Installing Software......................................................................................... 5-25
SuperDoctor® 5 ............................................................................................ 5-26
5-13 Onboard Battery............................................................................................ 5-27
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices.................................................................................. 6-1
Precautions ..................................................................................................... 6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 Accessing the Inside of the System................................................................ 6-3
6-4 System Fans ................................................................................................... 6-4
System Fan Failure......................................................................................... 6-4
Installing the Rear Exhaust Fans.................................................................... 6-4
6-5 Drive Bay Installation/Removal ....................................................................... 6-5
Hot-Swap Drive Bays...................................................................................... 6-5
Installing a Peripheral Drive............................................................................ 6-7
6-6 Power Supply.................................................................................................. 6-8
Power Supply Failure...................................................................................... 6-8
Replacing the Power Supply........................................................................... 6-8
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
7-2 Main Setup...................................................................................................... 7-2
7-3 Advanced Setup Congurations...................................................................... 7-3
7-4 Event Logs .................................................................................................... 7-31
4-5 IPMI............................................................................................................... 7-33
7-6 Security Settings ........................................................................................... 7-36
7-7 Boot Settings................................................................................................. 7-39
7-8 Save & Exit ................................................................................................... 7-41
Appendix A BIOS Error Beep Codes
Appendix B System Specications
SUPERSERVER 6048R-TXR User's Manual

Chapter 1
Introduction
1-1 Overview
The SuperServer 6048R-TXR is comprised of two main subsystems: the
SC842XTQ-R606B 4U server chassis and the X10DRX dual Intel Xeon processor
serverboard. Please refer to our website for information on operating systems that
have been certied for use with the system (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the server, as listed below:
•Two 8-cm rear exhaust fans (FAN-0082L4)
•One 9-cm front intake fan (FAN-0097L4)
•Two active CPU heatsinks (SNK-P0048AP4)
•SATA accessories:
One HDD backplane (BPN-SAS-842TQ)
Five 3.5" hard disk drive trays (MCP-220-00075-0B)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
•Supermicro product manuals: http://www.supermicro.com/support/manuals/
•Product drivers and utilities: ftp://ftp.supermicro.com
•Product safety info: http://www.supermicro.com/about/policies/safety_informa-
tion.cfm
•If you have any questions, please contact our support team at:
[email protected]
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 6048R-TXR User's Manual
1-2 Serverboard Features
At the heart of the SuperServer 6048R-TXR lies the X10DRX, a dual processor
serverboard based on the Intel C612 chipset. Below are the main features of the
X10DRX. (See Figure 1-1 for a block diagram of the chipset.)
Processors
The X10DRX supports two Intel®E5-2600 v3 series processors in LGA 2011 sockets
(Socket R3). Please refer to the serverboard description pages on our website for
a complete listing of supported processors (www.supermicro.com).
Memory
The X10DRX has sixteen DIMM slots that can support up to 1024 GB of LRDIMM
or 512 GB of RDIMM DDR4-2133/1866/1600 memory. Modules of the same size
and speed are recommended. See Chapter 5 for details.
Serial ATA
A SATA controller is integrated into the chipset to provide a ten-port SATA 3.0
subsystem, which is RAID 0, 1, 5 and 10 supported. The I-SATA0 through I-SATA5
ports are supported by the Intel PCH while the S-SATA0 through S-SATA0-3 ports
are supported by the Intel SCU. The SATA drives are hot-swappable units.
Note: The operating system you use must have RAID support to enable the hot-
swap capability and RAID function of the Serial ATA drives.
PCI Expansion Slots
The X10DRX has ten PCI-E 3.0 x8 and one PCI-E 2.0 x4 (in x8) slots for a total
of eleven PCI expansion slots.
Rear I/O Ports
The I/O ports include one COM port, a VGA (monitor) port, four USB 2.0 ports, a
dedicated IPMI LAN port and two Gb Ethernet LAN ports.
IPMI
IPMI (Intelligent Platform Management Interface) is a hardware-level interface
specication that provides remote access, monitoring and administration for
Supermicro server platforms. IPMI allows server administrators to view a server’s
hardware status remotely, receive an alarm automatically if a failure occurs, and
power cycle a system that is non-responsive.

1-3
Chapter 1: Introduction
1-3 Server Chassis Features
The following is a general outline of the main features of the SC842XTQ-R606B
server chassis.
System Power
The SC842XTQ-R606B features a redundant 600W high-efciency power supply
composed of two separate power modules. This power redundancy feature allows
you to replace a failed power supply without shutting down the system.
SATA Subsystem
The SC842XTQ-R606B supports up to ve 3.5" SATA drives. These drives are
hot-swappable units and are connected to a backplane that provides power and
control. Three additional 5.25" drive bays are included, which are not hot-swappable.
Front Control Panel
The control panel on the SuperServer 6048R-TXR provides you with system
monitoring and control. LEDs indicate system power, HDD activity, network activity,
system overheat/fan fail and power supply failure. The main power button and a
system reset button are also located here.
Cooling System
The SC842XTQ-R606B chassis has an innovative cooling design that includes one
9-cm front intake fan and two 8-cm rear exhaust fans. The power supply module
also includes a cooling fan.

1-4
SUPERSERVER 6048R-TXR User's Manual
Figure 1-1. Intel C612 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
6 PHASE
145W
VR12.5
VCCP0&1 12v
P1
P1
P0
P0
DMIPE1PE2PE3
PE3PE1PE2
port 4,5(USB2.0)
REAR
#1#2
A
G
PROCESSOR 1
PROCESSOR 2
#2#1
DDR4 DIMM
REAR
B
C
D
E
F H
#1
#2
#1
#2
#1 #2 #2#1
#1
#2#1 #2
port 1,2(USB3.0)+
port 0,1(USB2.0)
port 3,4(USB3.0)
+
port 2,3(USB2.0)port 8,9(USB2.0)
TYPE A
port 5(USB3.0)
+port 10(USB2.0)
PCIE-3.0 x8 * 5PCIE-2.0 x4 * 1
x8 * 5
PCIE3.0 x8 Slots [6/7/8/9/10]
PCIE2.0 x8 Slots 11(x4)
CPU REAR
CPU FRONT
QPI
DDR4 DIMM DDR4 DIMM
DDR4 DIMM
DDR4 DIMM DDR4 DIMM
DDR4 DIMM DDR4 DIMM
QPI
9.6GT/s
PCIE3.0 x8 Slots [1/2/3/4/5]
4GB/s x4 UL1
Dual LAN
I350AM2
JLAN1
RJ45
JLAN2
RJ45
To BMC RMII port
NC-SI
S-SATA0
S-SATA1 S-SATA2
S-SATA3
I-SATA0 I-SATA1
I-SATA2 I-SATA3
I-SATA4 I-SATA5
sSATA Gen3 [0..3]
PET [5,6,7,8]
SATA Gen3 [0..5]
DMI
PCH
PET4
SPI
USB2.0 [0..5]
USB3.0 [1..6]
LPC
USB2.0 [6,7]
NC-SI(RMII)
UL1
BMC
AST2400
HWM
SPI FLASH
16MB BIOS
16MB BMC
SPI FLASH
DDR3
VGA
TPM Header
IPMI LAN
RJ45
PHY
RTL8211E
COM1
HDR 2x5
HDR 2x10
DMI
X10DRX Block Diagram Rev. 1.00

1-5
Chapter 1: Introduction
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.supermicro.com.tw

1-6
SUPERSERVER 6048R-TXR User's Manual
Notes

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 6048R-TXR
up and running. Following these steps in the order given should enable you to have
the system operational within a minimum amount of time. This quick setup assumes
that your system has come to you with the processors and memory preinstalled. If
your system is not already fully integrated with a serverboard, processors, system
memory etc., please turn to the relevant section in Chapter 5 for details on install-
ing specic components.
2-2 Unpacking the System
You should inspect the box the SuperServer 6048R-TXR was shipped in and note
if it was damaged in any way. If the server itself shows damage you should le a
damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer 6048R-
TXR. It should be situated in a clean, dust-free area that is well ventilated. Avoid
areas where heat, electrical noise and electromagnetic elds are generated. You
will also need it placed near a grounded power outlet. Read the Rack and Server
Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 6048R-TXR was shipped in should include two sets of rail
assemblies, two rail mounting brackets and the mounting screws you will need to
install the system into the rack. Follow the steps in the order given to complete the
installation process in a minimum amount of time. Please read this section in its en-
tirety before you begin the installation procedure outlined in the sections that follow.
Choosing a Setup Location
•Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufcient airow and ease in servicing.

2-2
SUPERSERVER 6048R-TXR User's Manual
•This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets and the like).
•This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display
Units.
2-4 Warnings and Precautions
Rack Precautions
•Ensure that the leveling jacks on the bottom of the rack are fully extended to
the oor with the full weight of the rack resting on them.
•In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
•Always make sure the rack is stable before extending a component from the
rack.
•You should extend only one component at a time - extending two or more si-
multaneously may cause the rack to become unstable.
Server Precautions
•Review the electrical and general safety precautions in Chapter 4.
•Determine the placement of each component in the rack before you install the
rails.
•Install the heaviest server components on the bottom of the rack rst, and then
work up.
•Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
•Allow any hot plug drives and power supply modules to cool before touching
them.
•Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation
2-3
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the room's ambient temperature.
Therefore, consideration should be given to installing the equipment in an environ-
ment compatible with the manufacturer’s maximum rated ambient temperature
(Tmra).
Reduced Airow
Equipment should be mounted into a rack so that the amount of airow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
•This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
•When mounting this unit in a partially lled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.

2-4
SUPERSERVER 6048R-TXR User's Manual
2-5 Installing the System into a Rack
This section provides information on installing the SC842 chassis into a rack unit
with the quick-release rails provided. There are a variety of rack units on the market,
which may mean the assembly procedure will differ slightly. You should also refer to
the installation instructions that came with the rack unit you are using.
Mounting the Chassis in an Open (Telco) Style Rack
To install the chassis into a Telco type rack, use one L-shaped bracket on either
side of the chassis (two total). First, determine how far follow the server will extend
out the front of the rack. Larger chassis should be positioned to balance the weight
between front and back. If a bezel is included on your chassis, remove it, then at-
tach the two front brackets to each side of the chassis. Finish by sliding the chassis
into the rack and tightening the brackets to the rack. Additional L-brackets may be
purchased separately if additional support is required.
Figure 2-1. Mounting in an Open Style Rack
Notes: gure is for illustrative purposes only. Always install servers into racks from
the bottom up.

Chapter 2: Server Installation
2-5
Figure 2-2. Separating the Rack Rails
screw the handles the
outer rails for secure
purpose if necessary
F.
ABLECOM
DATE:2008/08/14
REV:2
SCREW
SCREW
COMPLETE
1
2
Separating the Inner and Outer Rails
1. Locate the rail assembly in the chassis
packaging.
2. Extend the rail assembly by pulling it
outward.
3. Press the quick-release tab.
4. Separate the inner rail from the outer
rail assembly.
Rail Assembly
Extending the Rails
Quick-Release
Tab
Separating the Inner
Rail
Rail System Overview
This section provides information on installing the SC842 chassis into a four-post
rack unit with the optional quick-release rails. There are a variety of rack units on
the market, which may mean the assembly procedure will differ slightly. You should
also refer to the installation instructions that came with the rack unit you are using.
Separating the Sections of the Rack Rails
The optional rail package includes two rail assemblies in the rack mounting kit. Each
assembly consists of two sections: an inner xed chassis rail that secures directly to
the server chassis and an outer xed rack rail that secures directly to the rack itself.

2-6
SUPERSERVER 6048R-TXR User's Manual
Figure 2-3. Installing the Inner Rails
Installing the Inner Rails
Installing the Inner Rails
1. Place the inner rails on the side of the chassis aligning the hooks of the chas-
sis with the rail holes. Make sure the rail faces "outward".
2. Slide the inner rail toward the front of the chassis.
3. Secure the chassis with two screws as illustrated. Repeat steps 1 and 2 for
the other inner rail.
1
1
1
2
1
3
1
3
Warning: In any instance of pulling the system from the rack, always use
a rack lift and follow all associated safety precautions.
Warning: When initially installing the server to a rack, test that the rail
locking tabs engage to prevent the server from being overextended. Have
a rack lift in place as a precaution in case the test fails.